EC11 - Taschenlampe Nitecore - Kostenlose Bedienungsanleitung

BEDIENUNGSANLEITUNG EC11 Nitecore

NITECORE®

The All-Round Flashlight Expert

Features

• Utilizes CREE XM-L2 (U2) LED
• Maximum output of 900 lumens
• Integrated "Precision Digital Optics Technology" provides extreme reflector performance
• Boasts a peak beam intensity of 9000 cd and a throw distance of up to 190 meters
  · Dual-switch design ensures unprecedented ease of use
  • Secondary red LED provides constant / flashing illumination
• Indicates battery voltage with a red flashing LED (accurate to 0.1V)
  · High efficiency constant current circuit enables maximum runtime of up to 20 hours
• Direct access to ultra-low and turbo output
• Reverse polarity protection prevents damage from an incorrectly inserted battery
• Detachable anti-rolling clip
• Toughened ultra-clear mineral glass with anti-reflective coating
• Constructed from aero grade aluminum alloy
  · HAIII military grade hard-anodized
  · Waterproof in accordance with IPX-8 (2 meters submersible)
• Impact resistant to 1.5 meters
  · Tail stand capability

Dimensions

Length: 2.95° (75mm)

Head diameter: 1" (25.4mm)

Tail diameter: 1" (25.4mm)

Weight: 1.60oz (45.3 gram) (without battery)

Accessories

Quality holster, (R)CR123 battery magazine,

clip, lanyard, spare o ring

Battery Options

	TYPE	Nominal voltage	Compatible
Primary Lithium battery	CR123	3V	Y (Recommended)
IMR18350 Rechargeable Li-ion battery	IMR18350	3.7V	Y
Rechargeable Li-ion battery	RCR123	3.7V	Y

Output & Runtime

FL1 STANDARD	TURBO	HIGH	MID	LOW	LOWER
IMR18350[IMAGE]	900LUMENS	300LUMENS	160LUMENS	70LUMENS	1LUMEN
	30mln	45mln	1h80 mln	2h30 mln	12 h
CR123[IMAGE]	430LUMENS	230LUMENS	100LUMENS	40LUMENS	1LUMEN
	45min	1h30 min	3h15 min	8h30 min	20 h
	190m (Beam Distance)
	9000cd (Peak Beam Intensity)
	1.5m (Impact Resistant)
	IPX-8, 2m(Waterproof AND Submersible)

NOTICE:

The stated data has been measured in accordance with the international flashlight testing standards ANSI/NEMA FL1, using 1 x high quality IMR18350 battery (3.7V 700mAh) or 1 x Nitecore CR123 battery (3V 1700mAh) under laboratory conditions. The data may vary during real-world use due to different battery usage or environmental conditions

Operating Instructions

Battery installation

Insert one (R)CR123 battery or one IMR18350 battery as illustrated NOTE: After loading the battery, the secondary red LED will flash to indicate battery voltage. Please refer to the "Power Tips" section of this manual for details.

WARNING:

1. Ensure the battery is inserted with the positive (+) end pointing towards the head. The EC11 will not be operational with an incorrectly inserted battery.
2. The included battery magazine securely holds the (R)CR123 battery in place, thus stopping battery movement in the compartment.
3. Please stop using and remove a depleted IMR18350 battery to avoid potential battery damage.

Diagram showing exploded view of a cylindrical device with labeled components and rotation arrows

On / Off Operation

To switch ON: Press the ON/OFF button once.

To switch OFF: Press the ON/OFF button once again to switch the light off and enter standby mode

Standby Mode

With the light switched on, press and hold the ON/OFF button for more than one second to switch the light off and activate the secondary red LED to flash once every three seconds, thus helping the user locate the EC11 in dark conditions. When using a CR123 battery, the EC11 will operate for up to 6 consecutive days with the red LED on, or remain on standby for more than 170 days with the red LED off.

Brightness Levels

With the EC11 switched on, press the MODE button repeatedly to cycle through the following brightness levels: ultra-low, low, medium, high and turbo. Once a mode is selected it will be saved and resumed when the EC11 is reactivated.

EC11 User Manual

Instant Ultra-low Output

With the light switched off, press and hold the ON/OFF button ☑ for more than one second to access ultra-low mode (1 lumen).

Instant Turbo Output

With the light switched off, press and hold the MODE button ☐ for more than one second to access turbo mode (900 lumens).

NOTE: When in turbo mode, the EC11 will adjust output luminance automatically within 3 minutes of use to prevent overheating and extend battery longevity.

Red Light / Signal Light Mode

With the light switched off, press the MODE button ☐ to enter red light mode. In this mode, the secondary red LED will illuminate steadily.

When in red light mode, press and hold the MODE button ☐ for more than one second to enter signal light mode. In this mode, the secondary red LED will flash to serve as a signal light. Simply press any button to exit the red light /signal light mode.

Special modes (Strobe/Location/SOS)

With the light switched on, press and hold the MODE button for more than one second to enter Strobe mode. When in strobe mode, press and hold the MODE button for more than one second again to cycle through Location Beacon, SOS and Strobe modes. To exit, simple press the MODE button to resume the last used brightness level, or press the ON/OFF button to switch the light off.

Strobe Ready

With the light switched off, press the MODE button twice in quick succession to enter Strobe mode. To exit, simply press any button.

Lockout / Unlock

With the light switched on, press and hold the ON/OFF button and the MODE button simultaneously for over one second to switch the light off and enter lockout mode. In lockout mode, the EC11 conserves battery power for over 170 days; the two buttons on EC11 will not work, thus preventing accidental activation of the light. To exit lockout mode, simply press and hold the ON/OFF button and the MODE button simultaneously for over one second again.

NOTE:

1. When entering lockout mode, the secondary red LED will continuously flash to indicate battery voltage. Please refer to the "Power Tips" section for more details.
2. When the EC11 is kept in a backpack or left unused for extended periods, Nitecore recommends the tailcap is loosened or battery is removed to cut off the power entirely, thus preventing accidental activation of the flashlight or battery leakage.

Power Tips

After battery installation or lockout mode activation, the secondary red LED will flash to indicate battery voltage (accurate to 0.1V). For example, when battery voltage is at 4.2V, the red LED will flash 4 times, followed by a one second pause and another 2 flashes. Different voltages represent the corresponding remaining battery power levels:

IMR18350: Low Power Full Power 4.2V 3.5V 3.7V 3.9V CR123: Low Power Full Power 3.2V 2.4V 2.8V 3.0V

Changing / Charging Battery

Battery should be replaced or recharged when output appears to be dim or the flashlight becomes unresponsive.

Maintenance

Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of silicon-based lubricant.

Warranty Service

All NITECORE® products are warranted for quality. Any DOA/defective product can be exchanged for a replacement through a local distributor/dealer within 15 days of purchase. After 15 days, all defective/malfunctioning NITECORE® products will be repaired free of charge for a period of 60 months (5 years) from the date of purchase. Beyond 60 months (5 years), a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts.

The warranty is nullified in all of the following situations:

1. The product(s) is/are broken down, reconstructed and/or modified by unauthorized parties.

2. The product(s) is/are damaged through improper use.

3. The product(s) is/are damaged by leakage of batteries.

For the latest information on NITECORE® products and services, please contact your national NITECORE® distributor or send an email to [e-mail]

The Nitecore official website shall prevail in case of any product data changes.

SYSMAX ind.

SYSMAX Industry Co., Ltd.

TEL: [phone]

FAX: [phone]

E-mail: [e-mail]

Web: www.nitecore.com

Address: Rm1401-03, Glorious Tower, 850 East Dongfeng Road,

Guangzhou, China 510600