EP772 - Vidéo-projecteur OPTOMA - Gratis bruksanvisning og manual

Produkttype	DLP-projektor
Merke	Optoma
Modell	EP772
Skjermteknologi	DLP 0,55 tommer
Opprinnelig oppløsning	XGA (1024 x 768)
Lysstyrke	3500 ANSI lumen
Kontrastforhold	2000:1
Linse	Manuell zoom 1,1x, vertikal forskyvning
Lampens levetid	3000 timer (normal modus), 4000 timer (økonomisk modus)
Dimensjoner (L x B x H)	294 x 234 x 99 mm
Vekt	2,9 kg
Strømforsyning	100-240 V, 50-60 Hz
Strømforbruk	280 W (maks), <0,5 W i standby
Vedlikehold og rengjøring	Rengjøring av luftfilter hver 500. time
Hovedfunksjoner	Høy lysstyrke projeksjon, vertikal trapeskorreksjon, 3D-klar
Sikkerhet	Kensington-lås, passord, barnesikring
Reservedeler og reparerbarhet	Reservedelspære (BL-FP230A), filter, fjernkontroll; pære og filter tilgjengelig for brukeren
Generell informasjon	Bruksanvisning tilgjengelig på flere språk på notice-facile.com

Ofte stilte spørsmål - EP772 OPTOMA

Hvordan installere projektoren?

Plasser apparatet på en stabil overflate, i passende avstand fra lerretet. Koble til kablene (HDMI, VGA, osv.) og koble til strømmen. Slå på med Power-knappen. Bruk zoom- og fokus-hjulene for å justere bildet.

Hva er projeksjonsavstanden for et 100 tommers bilde?

Med standardlinsen krever et 100 tommers lerret (diagonal) en avstand på ca. 3,0 til 3,3 meter avhengig av zoom. Se avstandstabellen i bruksanvisningen.

Hvordan bytte pæren?

Slå av apparatet og koble fra strømmen. Vent 30 minutter til det er avkjølt. Åpne pærerommet (skrue på siden), ta ut den gamle pæren og sett inn den nye (modell BL-FP230A). Lukk igjen og tilbakestill pæretelleren via menyen Innstillinger.

Hva gjør jeg hvis bildet er uskarpt?

Drei på fokus-ringen på objektivet til bildet blir skarpt. Kontroller at projeksjonsavstanden er riktig. Hvis uskarpheten vedvarer, rengjør linsen med en myk, lofri klut.

Hvordan rengjøre luftfilteret?

Slå av apparatet og koble fra strømmen. Åpne filterpanelet (plassert på siden). Ta ut filteret og støvsug det eller skyll det i lunkent såpevann. Tørk det helt før du setter det tilbake. Bytt det hver 500. time.

Kan jeg koble til en PC via HDMI?

Ja, apparatet har en HDMI-inngang. Bruk en standard HDMI-kabel for å koble til PC-en. Velg den tilsvarende kilden med Source-knappen på fjernkontrollen.

Hvordan bruke 3D-funksjonen?

For 3D trenger du en 3D-sender (selges separat) og kompatible aktive 3D-briller. Aktiver 3D-modus i menyen Visning og juster synkroniseringen. 3D-formatet må være DLP Link.

Hva betyr det blinkende lyset?

Et blinkende rødt Power-lys kan indikere overoppheting eller et pæreproblem. Kontroller at ventilasjonsåpningene ikke er blokkert og at luftfilteret er rent. Hvis problemet vedvarer, se kapittelet Feilsøking i bruksanvisningen.

Hvordan tilbakestille til fabrikkinnstillinger?

Gå til menyen Innstillinger (Settings), velg deretter Tilbakestill (Reset). Bekreft ved å trykke på OK. Alle innstillinger slettes og apparatet går tilbake til opprinnelige innstillinger.

Hvor finner jeg erstatningsfjernkontroll?

Den originale fjernkontrollen (referanse RC-06) er tilgjengelig hos autoriserte Optoma-forhandlere eller på spesialiserte nettsteder. Du kan også bruke en kompatibel programmerbar universalfjernkontroll.

BRUKSANVISNING EP772 OPTOMA

Table of Contents

Table of Contents....1

Usage Notice ....3

Introduction......6

Packing Checklist 6

Views of Projector....7

Remote Control....13

Remote Control Operating Range....15

Projector and Remote Control Buttons....15

Inserting the Remote Control Batteries....16

Setup and Operation....17

Connecting Input Devices....17

Starting and Shutting down the Projector ....19

Setting an Access Password (Security Lock) 21

Adjusting the Projector Level 23

Adjusting the Zoom, Focus and Keystone....24

Adjusting the Volume....24

OSD Menu Controls 25

Setting the OSD Language....26

Menu Setting 27

OSD Menu Overview 27

Image Menu....28

Display Menu....30

Setup Menu 32

Color setting Menu 35

Language Menu....36

Management Menu 37

Appendices....39

Replacing the Projection Lamp 39

Resetting the Lamp 42

Cleaning the Projector....43

Using the Kensington® Lock....43

Common problems and solutions....44

Tips for Troubleshooting....44

Table of Contents

LED Error Messages....45

Image Problems 46

Lamp Problems....46

Remote Control Problems....47

Audio Problems 47

Having the Projector Serviced....48

Specifications....49

Projection Distance V.S. Projection Size....49

Timing Mode Table....50

Projector Dimensions ....51

Regulatory Compliance....52

FCC Warning....52

Canada....52

Safety Certifications....52

EN 55022 Warning....52

RoHS Compliant 52

Usage Notice

Congratulations and thank you for choosing an EP771 projector, an on Optoma product. This product is an XGA single chip 0.7 inch DLP® projector!

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.

Precautions

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.

The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example:

"Push the Menu button on the remote control to open the Main menu."

Remote Control

Some remote controls have a laser for pointing out items on a screen.

DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently.

General Safety Information

Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
- Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.

Power Safety

▶ Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. Refer to “Replacing the Projection Lamp” on page 39 for clear and safe instructions for this procedure. Before replacing the lamp:

▶ Unplug the power cord.
- Allow the lamp to cool for about one hour.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

Cleaning the Projector

➢ Unplug the power cord before cleaning. Refer to “Cleaning the Projector” on page 43.
- Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the “Regulatory Compliance” section on page 52.

Main Features

• Lightweight unit, easy to pack away and transport
- Compatible with all major video standards including NTSC, PAL, and SECAM
- A high brightness rating allows for presentations in daylight or in lit rooms
• Supports resolutions up to SXGA at 16.7 million colors to deliver crisp, clear images
- Flexible setup allows for front and rear projections
- Line-of-vision projections remain square, with advanced keystone correction for angled projections
- Input source automatically detected

About this manual

This manual is intended for end users and describes how to install and operate the EP771 projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

Packing Checklist

Carefully unpack the projector and check that the following items are included:

Line drawing of a portable projector with display and control panel (no text or symbols)

EP771 PROJECTOR

Illustration of a remote control with two batteries (no text or symbols)

REMOTE CONTROL (WITH TWO AAA BATTERIES)

POWER CORD

Line drawing of a USB cable with two connectors (no text or symbols)

USB CABLE (USB TYPE A TO B USB)

VIDEO CABLE (RCA × 1 TO RCA × 1)

COMPUTER CABLE (DB15 - DB15)

Line drawing of a closed open briefcase with internal compartments (no text or symbols)

CARRYING CASE

Documents:

User's Guide

Quick Start Card

Warranty Card

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.

Caution:

Avoid using the projector in dusty environments.

Views of Projector

Front-right View

1 2 3 7 6 5438

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	Focus Focuses the projected image		24
2.	Lens zoom Enlarges the projected image		24
3.	Screws Holds lamp to projector
4.	See “Top view—OSD buttons and LEDs”		8
5.	IR receiver Receiver for IR signal from remote control		15
6.	Lens Remove lens cap before use
7.	Lens cover Slide across to protect lens when not in use
8.	Height-adjuster button	Push to release height adjuster	23

Important:

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.

Top view—On-screen Display (OSD) buttons and LEDs

graph TD
    A["LAMP"] --> B["POWER"]
    B --> C["KEYSTONE"]
    C --> D["ENTER"]
    D --> E["+/-"]
    E --> F["TOLE"]
    F --> G["KEYSTONE"]
    G --> H["POWER"]
    G --> I["RE-SYNC"]
    H --> J["SOURCE"]
    I --> K["MENU"]
    style A fill:#f9f,stroke:#333
    style B fill:#f9f,stroke:#333
    style C fill:#ccf,stroke:#333
    style D fill:#cfc,stroke:#333
    style E fill:#fcc,stroke:#333
    style F fill:#cff,stroke:#333
    style G fill:#ffc,stroke:#333
    style H fill:#cfc,stroke:#333
    style I fill:#cfc,stroke:#333
    style J fill:#fcc,stroke:#333
    style K fill:#fcc,stroke:#333

811109

43

ITEM	LABEL	DESCRIPTION		SEE PAGE:
1.	Keystone/Down cursor	Corrects image-trapezoid (wider bottom) effectNavigates and changes settings in the OSD		24
2.	VOL-/Left cursor	Decreases volumeNavigates and changes settings in the OSD		24
3.	Lamp LED	Orange Lamp ready—you can safely turn on or off the projector
		Flashing Lamp not ready—do not press the power button
4.	Keystone/UP cursor	Corrects image-trapezoid (wider top) effectNavigates and changes settings in the OSD
5.	Power LED	Green Unit is powered on and working correctly
		Off Unit is powered off
		Flashing Operational error code(Refer to “LED Error Messages” on page 45)

Introduction

ITEM	LABEL	DESCRIPTION	SEE PAGE:
6.	RE-SYNC Optimizes image size, position, and resolution		19
7.	Menu Opens and exits the OSD		25
8.	Source Detects the input device		19
9.	Power Turns the projector on or off

Rear view

1 2 3 4 5 6 16 15 14 13 12 11 10 9 8 7

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	Rear IR Receiver	Receiver for IR signal from remote control.	17
2.	DVI-D Connect the computer cable from a computer. Both DVI-I and DVI-D are supported.
3.	VGA IN Connect a VGA cable (supplied) from a computer
4.	VGA OUT Connect to a monitor
5.	S-video Connect the composite or S-video cable (supplied) from a video device
6.	Video Connect a composite video cable (supplied) from a video device.
7.	Audio in-R Connect the audio cable (not supplied) from an audio input device.
8.	Audio in-L Connect the audio cable (not supplied) from an audio input device.
9.	Audio-in Connect an audio cable (not supplied) from the computer's audio-out connector.
10.	Audio-out Audio loop-through
11.	USB Connect the USB cable (supplied) from a computer
12.	12V Connector Connect the 12V power outlet
13.	RS-232 Installation control

Introduction

ITEM	LABEL	DESCRIPTION	SEE PAGE:
14.	Power switch Turns the power on and off		43
15.	Power Connect the supplied power cord		43
16.	Security Lock Secure to permanent object with a Kensington® Lock system

Note:

If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video connector. S-video provides a better quality signal.

Bottom view

1 1 2 3 1 4

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	Ceiling support holes.	Contact your dealer for information on mounting your projector on the ceiling.
2.	Height adjuster button	Push to release height adjuster	23
3.	Height adjuster Adjuster drops down when adjuster button is pushed
4.	Tilt adjuster Adjust angle of the picture		23

Note: For ceiling installations, use approved mounting hardware and M3 screws with a maximum screw depth of 8 mm (0.31 inch).

Remote Control

28 1 2 27 Power Laser Up Enter Right Down 3 4 5 6 7 8 9 26 25 24 Up* Up* 23 22 Keystone Volume + - 10 11 21 20 19 18 17 Menu Reeze Zoom Re-Sync AV mute S-Video DVI VGA Composite 16 15

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user's manual describes the functions based on the remote control.

ITEM	LABEL	DESCRIPTION	SEE PAGE:
1.	IR transmitter Transmits signals to projector
2.	Status LED Lights when the remote control is used

Introduction

ITEM	LABEL	DESCRIPTION	SEE PAGE:
3.	Laser Press to operate the on-screen pointer
4.	Up Up arrow when connected through USB to a PC
5.	Right Right arrow when connected through USB to a PC
6.	Down Down arrow when connected through USB to a PC
7.	Page Down Page down when connected through USB to a PC
8.	Up cursor	Navigates and changes settings in the OSD
9.	Right cursor Adjusts volume
10.	Down cursor	Zoom in/out	24
11.	Volume +/-
12.	Zoom
13.	S-Video Input source select S-Video
14.	Composite Input source select Composite
15.	VGA Input source select VGA
16.	AV mute Display blank & Audio mute
17.	DVI Input source select DVI
18.	Re-Sync Re-Sync VGA source, adjustment for phase, tracking, size, position
19.	Menu Opens the OSD
20.	Freeze Freeze/unfreezes the on-screen picture
21.	Keystone top/bottom	Corrects image-trapezoid (wider top/bottom) effect	24
22.	Left cursor Navigates and changes settings in the OSD
23.	Enter Changes settings in the OSD		24
24.	Page Up	Page up when connected through USB to a PC	24

Introduction

ITEM	LABEL	DESCRIPTION	SEE PAGE:
25.	Left Left arrow when connected through USB to a PC
26.	Enter	Enter key when connected through USB to a PC
27.	Power Turns the projector on or off
28.	Laser Use as on-screen pointer. DO NOT POINT IN EYES.

The remote control can only interface with a computer when connected to the computer through a USB cable connection. The computer cable connects a computer to the projector for display purposes only.

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 10 meters (33 feet) and 30 degrees above or below the projector level.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however the buttons on the projector are limited in use. The following illustration shows the corresponding buttons on the remote control and on the projector.

Power Laser Up Enter Right Down 13 12 11 10 Keystone Volume + - 5 8 7 6 Menu Freeze Zoom Re-Sync AV mute S-Video DVI VGA Composite

3/8 5/10 9/12 11 2/4 LAMP POWER TONE ENTER TONE REVISIONS POWER RESYNC SOURCE MENU 1 6 8 7

Some buttons on the projector have two functions. For example, item 9/12 on the projector functions both keystone button and as the up cursor key in OSD menus.

Inserting the Remote Control Batteries

1. Remove the battery compartment cover by sliding the cover in the direction of the arrow.

Technical diagram of a device interior with a directional arrow indicating flow or movement (no text or symbols present)

1. Insert the supplied batteries taking note of the polarity (+/-) as shown here.

Diagram of a remote control casing with two batteries and arrows indicating rotation (no text or symbols)

1. Replace the cover.

Technical line drawing of a mechanical component with an arrow indicating direction (no text or symbols)

Caution:

1. Only use AAA batteries.(Alkaline battery is better).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.

Setup and Operation

Connecting Input Devices

A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.

A B C D E F M L K J I H G

ITEM LABEL DESCRIPTION
	Rear IR Receiver	Receiver for IR signal from remote control.
	DVI-D Connect the computer cable from a computer. Both DVI-I and DVI-D are supported.
	VGA in Connect a VGA cable (supplied) from a computer.
	VGA out Connect a VGA cable (supplied) to a monitor.
	S-video Connect the supplied S-video cable (not supplied) from a video device.
	Video Connect a composite video cable (supplied) from a video device.
	Audio in-R	Connect the audio cable (not supplied) from an audio input device.
	Audio in-L	Connect the audio cable (not supplied) from an audio input device.
	Audio-in Connect an audio cable (not supplied) from the computer's audio-out connector.
	Audio-out	Audio loop-through

Setup and Operation

ITEM LABEL DESCRIPTION
	USB Connect the supplied USB cable from a computer for USB mouse function and firmware upgrades.
	12V Connect a 12-volt trigger cable from the screen to this connector. When connected, the screen automatically adjusts vertically to match the screen aspect ratio.
	RS-232 Reserved for installation control.

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

Starting and Shutting down the Projector

1. Slide the lens cover.
2. Connect the power cord to the projector [A] Connect the other end to a wall outlet. Switch [B] from off (O) to on (—)
3. The POWER and LAMP LEDs on the projector turn on. Turn on the connected devices.
4. Ensure the LAMP LED is on a steady (not flashing) orange and then press the Power button to turn on the projector.

The projector splash screen displays and connected devices are detected. If the connected device is a PC, press the appropriate keys on the computer keyboard to switch the display output to the projector. (Check the user manual of the PC to determine the appropriate Fn key combination to change display output.)

See "Setting an Access Password (Security Lock)" on page 21 if Security Lock is enabled.

1. If more than one input device is connected, press the Source button repeatedly to switch among devices. (DVD and HDTV are supported through the VGA connector.)
2. To turn off the projector, press the Power button. The projector prepares for shutdown and a "Wait a moment please..." message appears.

graph TD
    A["Circle A"] --> Box["Box with - and ○ symbol"]
    B["Circle B"] --> Box
    Box --> D["Central Box with four small icons"]

Optoma DLP PROJECTION SYSTEM

Analog RGB 1024 x 768 @ 60 Hz

Wait a moment please ...

Setup and Operation

1. When the "Power Off? / Press Power again" message appears, press the Power button. The projector will turn off.

Power Off?

Press Power again

1. Turn off the main Power switch when the Lamp LED stops flashing.

Caution:

Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has cooled down.

Setting an Access Password (Security Lock)

You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 25 and Setting the OSD Language on page 26 for help on using OSD menus.)

Important:

Keep the password in a safe place. Without the password, you will not be able to use the projector. If you lose the password, contact your reseller for information on clearing the password.

1. Press the Menu button to open the 1.OSD menu.
2. Press the cursor ◀ button to move to the Management menu.
3. Press the cursor ▲ button to select Security.
4. Press the cursor button to select Enable. (White text is selected.) A password dialog box automatically appears.

Image Color setting Display Language Setup Management Menu Position Menu Display Translucent Menu Blank Screen Logo Display Security Status Reset Menu = Exit Menu select Scroll

Image Display Setup Color setting Language Management Menu Position Menu Display Translucent Menu Blank Screen Logo Display Security Enable Disable Status Reset Menu = Exit Item Adjust Scroll ▲▼

1. You can only use the following four cursor buttons: ▲▼◀▶ in the password fields. You can use any combination including the same arrow five times, but not less than six. Press the cursor buttons in any order to set the password. When you confirm the password, OK appears.

Password Register Password * * * * * Confirm Password * * * * * OK Exit : "MENU"

Setup and Operation

1. Every time you start the projector, a password dialog box appears.

Enter the password in the order you set it on step 5. (Press the Menu button to cancel if you enter the wrong password.)

Password Cancel : "MENU"

Setup and Operation

Adjusting the Projector Level

Take note of the following when setting up the projector:

• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Be sure cables are not in the way or can cause the projector to be knocked over.

A B C D

1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B].
   The height adjuster drops down [C].
2. To lower the level of the projector, press the height-adjuster button and push down on the top of the projector.
3. To adjust the angle of the picture, turn the tilt adjuster [D] right or left until desired angle has been achieved.

Adjusting the Zoom, Focus and Keystone

1. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B.
2. Use the Image-focus control (on the projector only) to sharpen the projected image.
3. Press the Keystone button on the remote control. The keystone control appears on the display.
4. Use the Keystone button to correct image distortion.

Adjusting the Volume

1. Press the Volume +/- button on the remote control. The volume control appears on the display.
2. Use the Volume +/- button to adjust the level.
3. Press the Mute button to turn off the volume.

A FOCUS ZOOM B

graph TD
    A["Keystone"] --> B["Volume"]
    C["VOL"] --> D["ENTER"]
    E["70k+"] --> D
    F["KEystone"] --> D
    G["KEystone"] --> D
    H["KEystone"] --> D

Keystone 0

graph TD
    A["Keystone"] --> B["Volume"]
    C["KEystone"] --> D["Volume"]
    E["Volume"] --> F["ENTER"]
    G["Volume"] --> H["ENTER"]
    I["Volume"] --> J["ENTER"]
    K["Volume"] --> L["ENTER"]
    M["Volume"] --> N["ENTER"]
    O["Volume"] --> P["ENTER"]
    Q["Volume"] --> R["ENTER"]
    S["Volume"] --> T["ENTER"]
    U["Volume"] --> V["ENTER"]
    W["Volume"] --> X["ENTER"]
    Y["Volume"] --> Z["ENTER"]
    AA["Volume"] --> AB["ENTER"]
    AC["Volume"] --> AD["ENTER"]
    AE["Volume"] --> AF["ENTER"]
    AG["Volume"] --> AH["ENTER"]
    AI["Volume"] --> AJ["ENTER"]
    AK["Volume"] --> AL["ENTER"]
    AM["Volume"] --> AN["ENTER"]
    AO["Volume"] --> AP["ENTER"]
    AQ["Volume"] --> AR["ENTER"]
    AS["Volume"] --> AT["ENTER"]
    AU["Volume"] --> AV["ENTER"]
    AW["Volume"] --> AX["ENTER"]
    AY["Volume"] --> AZ["ENTER"]

Volume 4

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.

1. To open the OSD, press the Menu button.
2. There are six menus. Press the cursor button to move through the menus.
3. Press the cursor button to move up and down in a menu.
4. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.
5. Press Menu to close the OSD or leave a sub-menu.

Color Setting Language Management Image Display Setup Display Mode Brightness Contrast White Peaking Saturation Tint Sharpness Color Temperature Menu = Exit Menu Select Scroll

Note:

Depending on the video source not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Setup menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.

Setting the OSD Language

You may want to reference the OSD on your projector while reading this section. Set the OSD language to your preference before continuing. (The default language is English.)

1. Press the Menu button. The Image menu appears.

Color Setting Language Management Image Display Setup Display Mode Brightness Contrast White Peaking Saturation Tint Sharpness Color Temperature Menu = Exit Menu Select Scroll

1. Press the cursor ◀ button until Language is highlighted.

Image Color setting Display Language Setup Management Language English English 简体中文 Norsk Français 繁體中文 Suomi Deutsch 한국어 Еллэнνικά Italiano Português Dansk Español Русский Polski Svenska Nederlands Menu = Exit Item Adjust Scroll

1. Press the cursor ▲▼ button until Language is highlighted.
2. Press the◀▶ button until your language is displayed.
3. Press the Menu button twice to close the OSD.

OSD Menu Overview

Use the following illustration* to quickly find a setting or determine the range for a setting.

graph TD
    A["Image"] --> B["Display mode"]
    B --> C["(1) Presentation * (2) Bright (3) Movie (4) Game (5) TV"]
    C --> D["Projection type"]
    D --> E["(1) Front & Desktop * (2) Rear & Desktop (3) Front & Ceiling (4) Rear & Ceiling"]
    E --> F["Video Type"]
    F --> G["(1) Auto * (2) NTSC (3) PAL (4) SECAM"]
    G --> H["Audio input"]
    H --> I["(1) PC (2) Video"]
    I --> J["Volume 0~8"]
    J --> K["Source lock"]
    K --> L["(1) on (2) off*"]
    L --> M["Auto Power Off (min.)"]
    M --> N["Direct Power On"]
    N --> O["(1) Disable * (2) 5, 10, 15,…,180"]
    O --> P["Lamp Mode"]
    P --> Q["Fan Mode"]
    Q --> R["(1) on (2) off*"]
    R --> S["Lamp Mode"]
    S --> T["Direct Power On"]
    T --> U["(1) ECO (2) Normal (3) Bright*"]
    U --> V["Lamp Mode"]
    V --> W["Fan Mode"]
    W --> X["(1) Normal * (2) High Altitude"]

    Y["Display"] --> Z["H. Image shift 0~100"]
    Z --> AA["V. Image shift 0~100"]
    AA --> AB["Keystone -50~+50"]
    AB --> AC["Format"]
    AC --> AD["Color Space"]
    AD --> AE["Digital Zoom"]
    AE --> AF["Frequency 0~100"]
    AF --> AG["Tracking 0~100"]

    AH["Management"] --> AI["(1) 4:3 * (2) 16:9 (3) Letter Box (4) Native"]
    AI --> AJ["(1) Auto * (2) RGB (3) YPbPr (4) YCbCr"]

    AK["Status"] --> AL["(1) Left (2) Right (3) Center * (4) Down (5) Up"]
    AL --> AM["Menu position"]
    AM --> AN["Menu Display 10~20 seconds"]
    AN --> AO["Translucent Menu"]
    AO --> AP["Blank Screen"]
    AP --> AQ["Logo Display"]
    AQ --> AR["Security"]
    AR --> AS["Status"]
    AS --> AT["Reset"]

    AU["Color setting"] --> AV["Red 0~100"]
    AV --> AW["Green 0~100"]
    AW --> AX["Blue 0~100"]
    AX --> AY["Cyan 0~100"]
    AY --> AZ["Magenta 0~100"]
    AZ --> BA["Yellow 0~100"]
    BA --> BB["White 0~100"]

    BC["Language"] --> BD["English"]
    BC --> BE["French"]
    BC --> BF["German"]
    BC --> BG["Italian"]
    BC --> BH["Spanish"]
    BC --> BI["Swedish"]
    BC --> BJ["Chinese-Simplified"]
    BC --> BK["Chinese-Traditional"]
    BC --> BL["Polish"]
    BC --> BM["Korean"]
    BC --> BN["Portuguese"]
    BC --> BO["Russian"]
    BC --> BP["Norwegian"]
    BC --> BQ["Dutch"]
    BC --> BR["Finnish"]
    BC --> BS["Greek"]
    BC --> BT["Danish"]

    style A fill:#f9f,stroke:#333
    style Y fill:#f9f,stroke:#333
    style AC fill:#f9f,stroke:#333

* Represents the default settings on the projector.

Image Menu

Press the Menu button to open the OSD menu.* Press the cursor ◀▶ button to move to the Image menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Color Setting Language Management Image Display Setup Display Mode Brightness Contrast White Peaking Saturation Tint Sharpness Color Temperature Menu = Exit Menu Select Scroll

ITEM DESCRIPTION DEFAULT
Display Mode	Press the cursor ◀▶ button to select different display mode. (Range: Presentation - TV)	Presentation
Brightness	Press the cursor ◀▶ button to adjust the brightness. (Range: 0 - 100)	50
Contrast Press the cursor button to adjust the contrast. (Range: 0 - 100) 50
White Peaking	White Peaking increases the output in the brightest whites without changing the blacks and dark grays. It crushes the whites slightly, but it does not appear to clip them or seriously obscure white detail. If you prefer a stronger image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting.Press ◀▶ to adjust the value of white peaking. (Range: 0 - 10)	Data source: 10Video source: 2
Saturation Press the cursor button to adjust the video saturation. (Range: 0 - 100)		50
Tint Press the cursor button to adjust the video tint/hue. (Range: 0 - 100)		50

Menu Setting

ITEM DESCRIPTION DEFAULT
Sharpness Press the cursor button to adjust the display sharpness (Range: 1-5)		3
Color Temperature	Press the cursor ◀▶ button to adjust the color temperature (Range: Cool/Normal/Warm)	Normal

*Note: Menu represents the default settings on the projector.

Image Menu Functions Available for Connected Source

Function RGB DVI			Component Video	Composite Video	S-Video
Display Mode	O	O	O		O
Brightness	O	O	O		O
Contrast	O	O	O		O
White Peaking	O	O	O		O
Saturation				O	O
Tint				O	O
Sharpness	O	O	O		O
Color Temp	O	O	O		O

O = available to video source

Display Menu

Press the Menu button to open the OSD menu. Press the cursor ◀▶ button to move to the Display menu. Press the cursor ▲▼ button to move up and down in the Display menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Color Setting Image Language Display Management Setup H. Image Shift V. Image Shift Keystone Format Color Space Digital Zoom Frequency Tracking Menu = Exit Menu Select Scroll

ITEM	DESCRIPTION	DEFAULT
H. Image Shift	Press the cursor button to adjust the display position in horizontal direction. (Range: 0 – 100)	Center position
V. Image Shift	Press the cursor button to adjust the display position in vertical direction. (Range: 0 – 100)	Center position
Keystone Press the cursor button to correct distortion of the projected image.(Range: -50 – +50)		0
Format Press the cursor button to toggle within the 4:3 standard format ,the 16:9 High Definition TV (HDTV) format , Little Box format and Native format		4:3
Color Space	Press the cursor button to adjust the color space.(Range: Auto – RGB – YPbPr- YCbCr)	Auto

Menu Setting

ITEM	DESCRIPTION	DEFAULT
Digital Zoom	Digital operation for zoom and pan adjustment. Press Enter or ▶. The Zoom menu appears.Press ▲ to zoom in; press ▼ to zoom out. Press Enter or ▶ to open the Pan menu. (You must zoom in before you can open the Pan menu.)Use the cursor buttons to pan the zoomed image. Press the Menu button to exit.	—
Frequency	Press the cursor button to adjust the A/D sampling clock. (Range: 0° –180°)	—
Tracking	Press the cursor button to adjust the A/D sampling number. (Range: 0 – 100)	—

Display Menu Functions Available for Connected Source

Function RGB DVI			Component Video	Composite Video	S-Video
H. Image Shift O
V. Image Shift O
Keystone	O	O	O	O	O
Format	O	O	O	O	O
Color Space	O	O	O	O	O
Digital Zoom	O		O	O	O
Frequency	O		O
Tracking	O

O = available to video source

Setup Menu

Press the Menu button to open the OSD menu. Press the cursor ◀▶ button to move to the Setup menu. Press the cursor ▲▼ button to move up and down in the Setup menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Color Setting Image Language Display Management Setup Projection Type Video Type Audio Input Volume Source Lock Auto Power Off (min.) Direct Power On Lamp Mode Fan Mode Menu = Exit Menu Select Scroll

ITEM	DESCRIPTION	DEFAULT
Projection Type	Press the cursor ◄ button to choose from four projection methods:P Desktop mount, front of screenq Desktop mount, rear of screend Ceiling mount, front of screenb Ceiling mount, rear of screen	Desktop frontP
Video Type	Press the cursor button to select the video standard (Range: Auto - NTSC - PAL - SECAM)	Auto
Audio Input	Press the cursor ◄► button to toggle between PC and Video input channels.	Data Source:PC Video Source:Video

Menu Setting

ITEM	DESCRIPTION	DEFAULT
Volume Press	the cursor button to adjust the audio volume level. (Range: 0 – 8)	4
Source Lock	Enable or disable the automatically searching of all input port to find out the valid source.	Off
Auto Power Off (min.)	Automatically lamp off when no signal. (Range: Disable – 180)	Disable
Direct Power On	Automatically power on when AC power applied.	Off
Lamp Mode Press	Press the cursor button to choose the lamp mode. Range: Eco, Normal and Bright.Eco mode uses less power and extends lamp life, but decreases lamp brightness.Bright mode uses more power and reduces lamp life, but increases lamp brightness.	Bright
Fan Mode	Press the cursor ◀▶ button to change fan mode; recommend turning into high speed in high temperature, high humidity or high altitude area.Set Fan mode to High Altitude over 1500 meters (5000 feet).	Normal

Note:

The Setup menu functions are available to all video sources.

Setup Menu Functions Available for Connected Source

Function RGB DVI			Component Video	Composite Video	S-Video
Projection Type	O	O	O		O
Video Type					O
Audio Input	O	O	O		O
Volume	O	O	O	O	O
Source Lock	O	O	O		O
Auto Power Off	O	O	O		O
Direct Power On	O	O	O		O
Lamp Mode	O	O	O		O
Fan Mode	O	O	O		O

O = available video source

Color setting Menu

Press the Menu button to open the OSD menu. Press the cursor ◀▶ button to move to the Color setting menu. Press the cursor ▲▼ button to move up and down in the Color setting menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Image Color Setting Display Language Setup Management Red 80 Green Blue Cyan Magenta Yellow White Menu = Exit Item Adjust Scroll

ITEM DESCRIPTION DEFAULT
Red Press	the cursor button to adjust the red color level. (Range: 0 - 100)	80
Green	Press the cursor ◀▶ button to adjust the green color level. (Range: 0 - 100)	80
Blue	Press the cursor ◀▶ button to adjust the blue color level. (Range: 0 - 100)	80
Cyan	Press the cursor ◀▶ button to adjust the cyan color level. (Range: 0 - 100)	80
Magenta	Press the cursor ◀▶ button to adjust the magenta color level. (Range: 0 - 100)	80
Yellow	Press the cursor ◀▶ button to adjust the yellow color level. (Range: 0 - 100)	80
White	Press the cursor ◀▶ button to adjust the white color level. (Range: 0 - 100)	80

Language Menu

Press the Menu button to open the Main menu. Press the cursor ◀▶ button to move to the Language menu. Press the cursor ▲▼ button to move up and down in the Language menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Image Color setting Display Language Setup Management Language English English 简体中文 Norsk Français 繁體中文 Suomi Deutsch 한국어 Ελληνικά Italiano Português Dansk Español Русский Polski Svenska Nederlands Menu = Exit Item Adjust Scroll

ITEM	DESCRIPTION	DEFAULT
English	Press the cursor ◀▶ to select the desired language. Press the Menu button twice to close the OSD	English
Français
Deutsch
Italiano
Español
Svenska
简体中文
繁體中文
한국어
Português
Русский
Nederlands
Norsk
Suomi
Ελληνικά
Dansk
Polski

Management Menu

Press the Menu button to open the Main menu. Press the cursor ◀▶ button to move to the Management menu. Press the cursor ▲▼ button to move up and down in the Management menu. Press ◀▶ to change values for settings, and then press Enter or ▶ to confirm the new setting.

Image Display Setup Color Setting Language Management Menu Position Menu Display Translucent Menu Blank Screen Logo Logo Display Security Status Reset Menu = Exit Menu Select Scroll

ITEM	DESCRIPTION	DEFAULT
Menu Position Press the cursor button to select different OSD location.: Left Right Center Up Down	Center
Menu Display Press the cursor button to select OSD timeout delay. (Range: 10 – 20 seconds)	15

Menu Setting

ITEM	DESCRIPTION	DEFAULT
Translucent Menu	Press the cursor button to select OSD back-ground translucent level. (Range: 0% - 25% - 50% - 75% - 100%)	0%
Blank Screen	Press the cursor ◀▶ button to select a background color for the blank screen. (Range: Black - Red - Green - Blue - White)	Blue
Logo Display	Press ◀▶ to enable or disable if the logo displays when the projector starts, and when no source is detected. (Range: On - Off)	On
Security Press the cursor button to enable or disable Security Lock. When you enable Security Lock a Register Password dialog box appears:		Disable
		You can only use the following four cursor buttons, ▲▼◀▶in the password fields. Press the cursor buttons five times in any order and confirm to set the password. When the password is enabled, it must be entered every time after you power on the projector. See “Setting an Access Password (Security Lock)” on page 21 for steps on setting the password.
Status	Press ▶the cursor Status menu.You can see Lamp Hours , Video Information , Active Source and Reset Lamp Hour in Status menu. See “Resetting the Lamp” on page 42.	or Enter b
Reset	Press ▶to reset settings to default values	—

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

1. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations.
2. Avoid touching the glass surface of the new lamp-doing so may shorten its operation life.

Warning:

Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to do so could result in a severe burn.

1. Loosen the two captive screws on the lamp compartment cover (A).

A B

Appendices

1. Open the lamp compartment cover (B).

Diagram of an open projector with a slide and labeled component 'B' (no text or symbols on the device itself)

1. Remove the two screws from the lamp module (C).

C D

1. Lift the module handle up (D).

Appendices

1. Pull firmly on the module handle to remove the lamp module (D)

Technical line drawing of an open projector with internal components and a labeled component (D), no text or symbols present.

1. Reverse steps 1 to 5 to install the new lamp module.

Resetting the Lamp

After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:

1. Press the Menu button to open the Image menu.
2. Press the cursor button to move to the Management menu.

3. Press the cursor ▲button to move down to Status.

4. Press the cursor ▶ or Enter button to enter Status menu

Image Display Setup Color setting Language Management Menu Position Menu Display Translucent Menu Blank Screen Logo Display Security Status Reset Menu - Exit Item Adjust Scroll

Status Lamp Hours 0 0 0 Lamp Hour Reset Video Information 1024 x 760 @ 60 Hz Active Source Analog RGB Menu - Exit Item Adjust Scroll

1. Press the cursor ▲ button to move down to Lamp Hour Reset. Press the cursor ▶ or Enter button.

A message screen appears.

Lamp Hour Reset Please See User Manual ... Menu = Exit

1. Press the cursor buttons in this order: ▼; ▲; ◀▶ The Status menu appears again showing the Lamp Hours reset to zero.

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

Using the Kensington® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

Diagram showing a padlock labeled 'K' pointing to an electronic device with ports and labels like USB, VGA, and I/O ports.

Appendices

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.

• Use some other electrical device to confirm that the electrical outlet is working.
• Ensure the projector is turned on.
• Ensure all connections are securely attached.
• Ensure the attached device is turned on.
• Ensure a connected PC is not in suspend mode.
• Ensure a connected notebook computer is configured for an external display. (This is usually done by pressing an Fn-key combination on the notebook.)

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts.

For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting-the information may be useful when calling for technical support or for passing on to service personnel.

LED Error Messages

ERROR CODE MESSAGE	POWER LED/FLASHES	READY LED/FLASHES
Lamp usage task created error 2 1
Environment usage task created error 2 2
Thermal break status error 3 0
T1 temperature over temperature 3 1
T1 sensor status fail 4 1
Lamp lit error 5 1
Ballast SCI error 5 2
Ballast UART error 5 3
Fan1 error (Lamp) 6 1
Fan2 error (Ballast) 6 2
Fan3 error (Burner) 6 3
Fan4 error (Power) 6 4
Lamp door sensor detect high 7 0
DMD error 8 0
Color wheel error	9 0

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed or upside down

Check the Projection setting on the Utility menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC's video card, connect to another computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Main menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Main menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the projector. When the Ready LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem--the information may be useful to service personnel.

Optoma Global Offices

For service or support, please contact your local office.

USA

715 Sycamore Drive

Milpitas, CA 95035, USA

Tel: [phone]

Fax: [phone]

www.optomausa.com

Service: [e-mail]

Canada

5630 Kennedy Road,

Mississauga, ON, L4Z 2A9, Canada

Tel: [phone]

Fax: [phone]

www.optoma.com

Europe

42 Caxton Way, The Watford Business Park

Watford, Hertfordshire, WD18 8QZ, UK

Tel: [phone]

Fax: [phone]

www.optomaeurope.com

Service Tel: [phone]

Service: [e-mail]

Taiwan

5F., No. 108, Minchiuan Rd.

Shindian City, Taipei Taiwan 231

Tel: [phone]

Fax: [phone]

www.optoma.com.tw

Service: [e-mail]

Hong Kong

Rm. 2507, 25/F., China United Plaza,

No. 1008 Tai Nan West St., Kowloon, H.K.

Tel: [phone]

Fax: [phone]

www.optoma.com.hk

China

5F, No. 1205, Kaixuan Rd.,

Changning District, Shanghai, 200052, China

Tel: [phone]

Fax: [phone]

www.optoma.com.cn

Latin America

715 Sycamore Drive

Milpitas, CA 95035, USA

Tel: [phone]

Fax: [phone]

www.optoma.com.br

www.optoma.com.mx

Projection Distance V.S. Projection Size

Anchura de pantalla A B Altura de pantalla D C L Distancia de proyección

Projection Distance L	Max. Screen Size 1.8 Min. Screen Size(Tele) 2.1
	Diagonal	Width A	Height C	Diagonal	Width B	Height D
1.00 m 0.69 m 0.56 m 0.42 m 0.60 m 0.48 m 0.36 m
3'	27"	21"	16"	23"	18"	14"
1.50 m 1.04 m 0.83 m 0.63 m 0.89 m 0.71 m 0.54 m
4'	41"	32"	24"	35"	28"	21"
2.40 m 1.67 m 1.33 m 1.00 m 1.43 m 1.14 m 0.86 m
7'	65"	52"	39"	56"	44"	33"
2.80 m 1.94 m 1.56 m 1.17 m 1.67 m 1.33 m 1.00 m
9'	76"	61"	45"	65"	52"	39"
3.20 m 2.22 m 1.78 m 1.33 m 1.90 m 1.52 m 1.14 m
10'	87"	69"	52"	74"	59"	44"
3.60 m 2.50 m 2.00 m 1.50 m 2.14 m 1.71 m 1.29 m
11'	98"	78"	59"	84"	67"	50"
4.00 m 2.78 m 2.22 m 1.67 m 2.38 m 1.90 m 1.43 m
13'	109"	87"	65"	93"	74"	56"
4.40 m 3.06 m 2.44 m 1.83 m 2.62 m 2.10 m 1.57 m
14'	120"	96"	72"	103"	82"	61"
4.80 m 3.33 m 2.67 m 2.00 m 2.86 m 2.29 m 1.71 m
15'	131"	104"	78"	112"	89"	67"
5.20 m 3.61 m 2.89 m 2.17 m 3.10 m 2.48 m 1.86 m
17'	142"	113"	85"	121"	97"	73"
5.60 m 3.89 m 3.11 m 2.33 m 3.33 m 2.67 m 2.00 m
18'	153"	122"	91"	131"	104"	78"
7.00 m 4.86 m 3.89 m 2.92 m 4.17 m 3.33 m 2.50 m
22'	191"	153"	114"	164"	131"	98"
10.00 m	6.94 m 5.56 m 4.17 m 5.95 m 4.76 m 3.57 m
32'	273"	218"	164"	234"	187"	140"

Shaded rows are equivalent measurement in feet and inches

Timing Mode Table

The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector.

Signal Resolution		Frequency H. (KHz)	Frequency V. (Hz)	Video Digital Analog
NTSC	--	15.734	60.0	○	--	--
PAL / SECAM	--	15.625	50.0	○	--	--
VESA	640 x 350 37.9	85.1 --			○ ○
	720 x 400 31.5	70.0 --			○ ○
	720 x 400 37.9	85.0 --			○ ○
	640 x 480 31.5	60.0 --			○ ○
	640 x 480 37.9	72.8 --			○ ○
	640 x 480 37.5	75.0 --			○ ○
	640 x 480 43.3	85.0 --			○ ○
	800 x 600 37.9	60.3 --			○ ○
	800 x 600 46.9	75.0 --			○ ○
	800 x 600 48.1	72.2 --			○ ○
	800 x 600 53.7	85.1 --			○ ○
	1024 x 768 48.4	60.0 --			○ ○
	1024 x 768 56.5	70.1 --			○ ○
	1024 x 768 60.0	75.0 --			○ ○
	1024 x 768 68.7	85.0 --			○ ○
	1280 x 1024 64.0	60.0 --			○ ○
	1600 x 1200 ** 75.0	60.0 --	--			○
Apple Macintosh	640 x 480 35.0	66.7 --			○ ○
	832 x 624 49.7	74.5 --			○ ○
	1024 x 768 60.2	74.9 --			○ ○
	1152 x 870 68.7	75.1 --			○ ○
HDTV	1920 x 1080 33.8	30.0 --				○
	1920 x 1080 28.1	25.0 --				○
	1280 x 720 45.0	60.0 --				○
SDTV	720 x 576 31.3	50.0 --				○
	720 x 480 31.5	60.0 --				○

O: Frequency supported
--: Frequency not supported
The native resolution is 1024 x 768. Resolution other than native mode may be displayed with uneven size of text or lines.
UXGA resolution with half-sampling.

Projector Dimensions

300 mm (11.8") 108 mm (4.3") 244 mm (9.6") LAMP POWER KEYSTONE ENTEN RE-SYNC POWER RE-SYNC SOURCE MENU

Regulatory Compliance

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user's authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC Class B, UL, C-UL, CE, CB, TUV-GS, CCC, ICES-003 (class B), MIC

EN 55022 Warning

This is a Class B product. In a domestic environment, it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room, or auditorium.

RoHS Compliant

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

© Copyright September, 2006

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.