UF0401K - Kluis Phoenix - Gratis gebruiksaanwijzing en handleiding

Producttype	Inbouwkluis
Merk	Phoenix
Model	UF0401K
Deurtype	Rond
Materiaal kluislichaam	Staal
Materiaal hals	ABS-kunststof
Installatiemethode	Inbetonneren met wapening
Minimale betondikte rondom	150 mm
Minimale installatietemperatuur	3 °C
Uithardingstijd beton	14 dagen
Onderhoud	Deur en kraag droog en schoon houden, licht oliën
Garantie	Registratie via www.phoenixsafe.com
Aanbevolen accessoire	Silicagel tegen condensatie
Veiligheid	Geschikt voor verzekering (na overleg)
Gebruik	Uitsluitend voor binnenvloer
Reiniging	Geen water in de kluis, droog reinigen
Wapening	Staalgaas (Weldmesh Ref. 26)
Halsmontage	Volledig in stalen kraag, eventueel verlijmen
Deur	Verwijderbaar tijdens installatie

Veelgestelde vragen - UF0401K Phoenix

Hoe installeer ik de Phoenix UF0401K kluis?

U begint met het voorbereiden van de locatie: verwijder vloerbedekking en graaf een gat van minimaal 150 mm ruimer dan de kluis. Plaats een betonlaag van 100 mm, zet de kluis erin en controleer of deze waterpas is. Vul het gat met beton in lagen van 100 mm, voeg wapening toe en laat 14 dagen uitharden.

Moet ik wapening gebruiken?

Ja, staalgaas (Weldmesh Ref. 26) is vereist voor een stevige constructie. Plaats een verticale laag rond de hals en een horizontale laag onder het vloerniveau.

Hoe lang moet ik wachten na installatie?

Na het storten van het beton moet u 14 dagen wachten voordat u de kluis mag gebruiken.

Kan ik de kluis in een houten vloer installeren?

Ja, maar u moet bekisting gebruiken om het beton binnen de juiste afmetingen te houden.

Hoe onderhoud ik de kluis?

Houd de deur en de kraag droog, schoon en licht geolied. Voorkom dat er water in de kluis komt.

Wat moet ik doen bij condensatie?

Gebruik silicagel om condensatie te voorkomen, vooral als de kluis voor langere tijd gesloten blijft.

Hoe registreer ik de garantie?

Ga naar www.phoenixsafe.com en klik op 'guarantee registration' om uw garantie te registreren.

Is de kluis geschikt voor verzekering?

Ja, maar u moet uw verzekeringsmaatschappij vooraf op de hoogte stellen van uw installatieplannen.

Kan ik de deur verwijderen?

Ja, tijdens de installatie kunt u de deur verwijderen om verontreiniging te voorkomen. Plaats de deur pas na het uitharden van het beton terug.

Wat als de hals verschuift?

U kunt de ABS-hals verlijmen om te voorkomen dat deze tijdens het storten verschuift. Zorg dat de hals volledig in de stalen kraag zit.

GEBRUIKSAANWIJZING UF0401K Phoenix

PLEASE READ CAREFULLY

INTRODUCTION

To ensure their high security attributes, Underfloor Safes require a High Grade Concrete Encasement containing suitable reinforcement.

LOCATION

The installation should be undertaken by a qualified installer whose survey would determine a convenient ground floor site free from any electrical wiring, water or gas pipes, etc., and where the use of attacking tools would be restricted.

INSURANCE

If the safe is for insurance requirements your insurance company should be made aware of your intention prior to installation.

WHEN THE INSTALLATION IS COMPLETE NO PORTION OF THE NECK OR DEPOSIT TUBE MUST PROTRUDE ABOVE FLOOR LEVEL.

SAFE PREPARATION

1. Remove door from safe to a place away from site to avoid any form of contamination.
2. To prevent dust or concrete from entering during installation fill the inside of the safe and neck with crumpled newspaper.
3. For round door models ensure that the A.B.S neck is fully engaged in the steel collar. Where two necks are used see that they are correctly located. Single or double A.B.S necks may be glued to avoid subsequent dislodgement.
4. Apply sealant around neck-to-collar joint. Replace lid

REINFORCEMENT

Steel reinforcement must be used. A suitable type is Weldmesh Ref. No.26: 2" x 2" (50 mm x 50mm) x 6 S.W.G. Round door safes require a vertical layer approximately 9" (225mm) diameter by 3" (75mm) high formed to fit around the A.B.S neck. A 30" x 30" (762 mm x 762mm) piece is notched at the corners and the edges are bent downward leaving a horizontal layer approximately 22" x 22" (560 mm x 560mm). A hole is cut into the mesh to accommodate the neck and to allow positioning in the concrete 2" (50mm) below floor level. Additional steel reinforcement may be added to increase concrete protection at sides of safe if required. Reinforcement is arranged similarly for square door safes with both vertical and horizontal layers.

SITE PREPARATION

1. Remove any floor covering and expose concrete floor.
2. Mark an area on the floor to allow not less than 6" (150mm) of concrete round the sides of the safe.
3. Cut through the concrete and excavate to a depth of 3" (75mm) more than the total depth of the safe.
4. Angle the sides of the hole outwards by 2" in order that the concrete is dovetailed into the floor.
5. For installation in a wooden floor it will be necessary to confine the concrete to the dimensions given with the use of shuttering.

CONCRETE PREPARATION AND DAMP-PROOFING

Use only good quality sand, aggregate and cement.

Recommended Specification:

PARTS BY WEIGHT

Coarse Graded Aggregate 3/4 " MAX 3

Fine Graded Aggregate 3/16" MAX 1 ½

Ordinary Portland Cement 1

Water Not to exceed 24.4 litres for every 50 kgs of Cement

All materials to conform to the appropriate British Standard Specification.

A suitable dry mix preparation is Marley Mix 3-1 1/2 - 1 B.S 5838 Part 1

DO NOT CONCRETE UNLESS THE AMBIENT TEMPERATURE IS AT LEAST 3°C MIN.

Materials must be frost free and in cold conditions use water heated to 10° C. Accelerating or other admixtures containing calcium chloride must not be used as these are highly corrosive. The addition of a waterproofing agent, however, may be necessary. Where site excavation reveals extreme damp presence, the hole should be lined with a heavy gauge polythene sheeting.

Thoroughly dry mix all materials and then add a minimum of water to allow the concrete to be compacted. Do not add too much water as this will reduce the strength of the construction. The amount of water shown in the column above produces a 2" (50 mm) slump which should not be exceeded.

SAFE INSTALLATION

1. Cover the base of the hole with 4" (100 mm) of the concrete mix.
2. Lift safe by top plate (avoid dislodging round type neck), place in centre of hole and work down into the concrete bed until the lid is at the correct level with surrounding floor.
3. Use a spirit level to span the hole to check the safe is level.
4. The concrete is added in layers of 4" (100mm): each layer worked well into the previous layer with a tamping tool. A section of timber, or similar, about 39" (1m) long, with a ramming face approximately 1" (25mm) square is ideal for the purpose. Work methodically over entire surface and ensure full compaction of concrete. Take care not to disturb the safe or dislodge the neck through-out installation.
5. The steel reinforcement is introduced into the concrete at the appropriate stage.
6. When the hole is filled with the concrete mix to within 1/2 “ (12mm) of the surface, take the safe door from bag and after removing lid, insert door into safe to ensure that misalignment has not occurred. ANY NECESSARY ADJUSTMENT WOULD NEED TO BE MADE NOW BEFORE CONCRETE IS SET.
7. Screed last 1/2 “ (12mm) with a mixture of sand and cement to bring to a smooth finish. THE SAFE MUST NOT BE USED FOR 14 DAYS AFTER INSTALLATION.

CARE AND MAINTENANCE

The subsequent application of a lino paint by the owner/user will act as a surface stabiliser and help to control grit. Ensure that any floor washing activity etc. does not result in water entering the safe. Keep safe door and locating collar dry, clean and lightly oiled. Dirt and grit etc. can be damaging to the locking mechanism. To ensure that the safe remains in good working order always close the escutcheon and see that the lid is replaced properly after use. The use of silica gel is recommended where condensation is a problem or where the safe remains locked for any extended period of time.

GUARANTEE REGISTRATION

Please submit your guarantee registration by visiting our website www.phoenixsafe.com and clicking on guarantee registration.

For further assistance or information please contact us on 0151 944 6444.

APEX HOUSE, 1 ORRELL MOUNT, LIVERPOOL,

L20 6NS, UNITED KINGDOM

[phone]