Question 1

Are batteries necessary for the portable CD player EBENCH KH 2257 - 2260 when it is plugged into an outlet?

Accepted Answer

For the portable CD player EBENCH KH 2257 - 2260, batteries are generally not necessary when the device is plugged into a power outlet. Indeed, the device operates normally solely with the power supplied by the power cable.

However, here are a few points to consider:

Operation on mains: When the device is plugged in, it directly uses the mains power to operate, which avoids battery consumption.
Use of batteries: Batteries are primarily intended for portable use, when the device is not connected to a power outlet.
Specific functions: Some models may use batteries to save certain data or settings in case of a power outage, but this depends on the exact model.

In summary, for standard use plugged into mains, batteries are not necessary and can be removed to avoid any unnecessary discharge. Batteries are only essential for portable use without mains power.

Question 2

Why does my EBENCH portable CD player display 'no disc' after a few seconds of spinning the CD?

Accepted Answer

The message 'no disc' that appears on your EBENCH KH 2257 - 2260 portable CD player after a few seconds of spinning indicates that the device is unable to read the inserted disc. Several causes may explain this issue:

1. Checking the CD

Make sure the CD is clean and in good condition, without scratches, dirt, or visible marks.
Test with another CD to check if the problem is with the disc or the player.
Check that the CD is compatible: some players do not read CD-R, CD-RW, or certain burned formats.

2. Positioning the CD

Properly place the CD on the tray, well-centered and clipped to avoid any misalignment.

3. Cleaning the player

The reading laser may be dirty. Use a CD cleaning disc to improve reading.

4. Resetting the device

Turn off the player, remove the batteries or unplug it if possible.
Wait a few minutes, then reinsert the batteries or plug the device back in and turn it on.

If after these checks and actions the problem persists, it is possible that the player has a hardware defect requiring repair or replacement.

Question 3

What to do when the portable CD player EBENCH KH 2257 - 2260 displays a flashing 'CD Read' without reading the CD and the FM radio is not working?

Accepted Answer

When your portable CD player EBENCH KH 2257 - 2260 displays the flashing 'CD Read' message and does not read the CD, here are the steps to follow to resolve this issue. Note: this device is a portable MP3-CD player without FM radio function.

First, check the power and batteries: Make sure the player is receiving power properly. If you are using batteries, check that they are not discharged - the flashing battery symbol on the LCD screen indicates a low battery. Recharge the supplied NiCd batteries in the player compartment by inserting the power adapter cable into the 'DC 4.5 V' socket on the left side, sliding the 'CHARGE' switch to the 'ON' position, and waiting for about 15 hours. If the batteries do not work after recharging, replace them with new NiCd AA 1.2 V batteries or non-rechargeable NiMh AA 1.5 V batteries.

Clean the laser lens: Condensation may have formed on the laser scanner lens, especially if the device has been exposed to significant temperature variations. Place the player in a dry environment at normal temperature, remove the CD from the compartment, and leave the device on for at least one hour without using it to allow the condensation to evaporate. If condensation persists after this time, gently clean the laser lens with a dry, clean brush (available at photographic product retailers). Never use a wet brush and never touch the lens with bare fingers, as fingerprints and moisture cause reading defects.

Check the disc and test another one: A damaged, scratched, or very dirty CD cannot be read properly. Inspect your disc for visible scratches or dirt. Try another CD - preferably a standard audio CD, CD-R, or CD-RW in audio format (.cda) or MP3 (.mp3) up to 256 kbps - to determine if the problem is with the disc or the player itself. Insert the disc label side up, press down gently until it clicks, then close the compartment by pressing the lid until you hear an audible click.

Check that the 'HOLD' mode is not activated: If the player does not respond to any buttons, the 'HOLD' slider on the left side of the player may be in the locked position. Slide this switch to the left to disable the button lock and free the controls.

Reset the device: Completely turn off the player by pressing the 'STOP/OFF' button twice (once to enter stop mode, a second time to turn it off - 'POWER OFF' appears). Unplug the power cable or remove the batteries. Wait 1 to 2 minutes, then reconnect the power. This reset may resolve temporary system bugs.

If the player still displays a flashing 'CD Read' after these steps, contact an authorized repair service. Never open the player casing - it contains no user-serviceable parts, and opening it voids the warranty.

User manual EBENCH Portable CD player : user manuals and guides in PDF

Models EBENCH Portable CD player most viewed

Other categories EBENCH

Recent questions about Portable CD player EBENCH