Q: The stopwatch on my MR DADDY 2.0 watch is not working - what should I do?

Diagnosis and solutions: If the stopwatch on your Diesel MR DADDY 2.0 watch has suddenly stopped after normal operation, here’s what to do: Checks to make Test the chronograph function - Press button A to start the stopwatch, then button B to reset it. Do you feel a slight mechanical resistance or a click with each press? Check the rest of the watch - Do the hours, minutes, and seconds display the correct time? Do the other functions respond normally to the buttons? Look for signs of moisture - Check under the watch glass. Is there any fogging or visible moisture? Has the watch been exposed to water recently? If nothing changes A sudden and complete stop of the stopwatch after normal operation usually indicates an internal mechanism defect : broken spring, jammed gear, or interrupted electrical contact. This type of defect is covered by the 2-year warranty from Diesel. Contact an authorized Diesel service center specifying: "The stopwatch stopped working for no reason after normal operation." They will be able to repair or replace the movement if necessary.

Q: The A and B buttons on my watch are not responding - what should I do?

If the A and B buttons on your MR DADDY 2.0 watch are not responding, here are the checks to perform: Preliminary Diagnosis Check that the watch is functioning - is the second hand moving? If nothing is moving at all, the battery may be dead or there is an internal problem. Press firmly and several times - the buttons may require a firm press to respond. Hold each button down for 2 seconds. Check for moisture - according to the manual, the buttons should NEVER be used underwater. If your watch has been submerged, this may block the button mechanism. Common Causes and Solutions According to the manual, the A Button controls the chronograph and the EL lighting, while the B Button resets the chronograph and changes display modes. If neither responds: The watch may have suffered a shock or exposure to saltwater that damaged the internal contacts. A residue or salt crystal may be blocking the buttons (if used near the sea). The battery may be low or dead, which can affect electronic functions. Recommended Steps Gently clean - rinse your watch with fresh water if it has been exposed to saltwater. Wait a few hours - if your watch has been wet, let it dry completely. Test again - after drying, press firmly on the buttons several times. If the buttons remain stuck after these checks, it is likely an internal defect (frozen mechanism, oxidized contacts, or dead battery). Your watch comes with a 2-year manufacturer's warranty against material or manufacturing defects. Contact an authorized Diesel service center for professional diagnosis and repair.

Question 1

The stopwatch on my MR DADDY 2.0 watch is not working - what should I do?

Accepted Answer

Diagnosis and solutions:

If the stopwatch on your Diesel MR DADDY 2.0 watch has suddenly stopped after normal operation, here’s what to do:

Checks to make

Test the chronograph function - Press button A to start the stopwatch, then button B to reset it. Do you feel a slight mechanical resistance or a click with each press?
Check the rest of the watch - Do the hours, minutes, and seconds display the correct time? Do the other functions respond normally to the buttons?
Look for signs of moisture - Check under the watch glass. Is there any fogging or visible moisture? Has the watch been exposed to water recently?

If nothing changes

A sudden and complete stop of the stopwatch after normal operation usually indicates an internal mechanism defect: broken spring, jammed gear, or interrupted electrical contact. This type of defect is covered by the 2-year warranty from Diesel.

Contact an authorized Diesel service center specifying: "The stopwatch stopped working for no reason after normal operation." They will be able to repair or replace the movement if necessary.

Question 2

The A and B buttons on my watch are not responding - what should I do?

Accepted Answer

If the A and B buttons on your MR DADDY 2.0 watch are not responding, here are the checks to perform:

Preliminary Diagnosis

Check that the watch is functioning - is the second hand moving? If nothing is moving at all, the battery may be dead or there is an internal problem.
Press firmly and several times - the buttons may require a firm press to respond. Hold each button down for 2 seconds.
Check for moisture - according to the manual, the buttons should NEVER be used underwater. If your watch has been submerged, this may block the button mechanism.

Common Causes and Solutions

According to the manual, the A Button controls the chronograph and the EL lighting, while the B Button resets the chronograph and changes display modes. If neither responds:

The watch may have suffered a shock or exposure to saltwater that damaged the internal contacts.
A residue or salt crystal may be blocking the buttons (if used near the sea).
The battery may be low or dead, which can affect electronic functions.

Recommended Steps

Gently clean - rinse your watch with fresh water if it has been exposed to saltwater.
Wait a few hours - if your watch has been wet, let it dry completely.
Test again - after drying, press firmly on the buttons several times.

If the buttons remain stuck after these checks, it is likely an internal defect (frozen mechanism, oxidized contacts, or dead battery). Your watch comes with a 2-year manufacturer's warranty against material or manufacturing defects. Contact an authorized Diesel service center for professional diagnosis and repair.

User manual Diesel Wristwatch : user manuals and guides in PDF

Models Diesel Wristwatch most viewed

Other categories Diesel

Recent questions about Wristwatch Diesel