VX600/1i - Receiver JL Audio - Free user manual and instructions
Find the device manual for free VX600/1i JL Audio in PDF.
| Product Type | Monoblock Class D Subwoofer Amplifier with Integrated DSP |
| Brand | JL Audio |
| Model | VX600/1i |
| Power Output | 600W RMS (monoblock) |
| Amplifier Class | Class D with NexD high-speed switching |
| Recommended Fuse | 50A (at battery, within 18 inches) |
| Input Voltage Range | 200 mV – 16V RMS (line-level analog) |
| Power Supply | 12V DC, negative ground |
| Analog Inputs | 2-channel RCA, differential-balanced, up to 16V RMS |
| Preamp Outputs | 2-channel RCA, max 4V RMS, configurable via TUN |
| Digital Input | 1 x Toslink optical (S/PDIF), up to 192 kHz |
| Digital Output | 1 x Toslink optical (24-bit/96 kHz) |
| USB Port | USB A/B for computer connection and TUN software |
| Optional Accessories | VX-BTC Bluetooth Communicator, VX-HUB, DRC (Digital Remote Controller) |
| Turn-On Modes | Conventional (+12V remote), DC offset, Digital Signal Sampling |
| Valet Mode | Activated by grounding the Valet wire, overrides DRC preset |
| DSP Features | Integrated Digital Signal Processor, configurable via TUN software |
| Warranty | 2 years (USA), limited to defects in materials and workmanship |
| Included Items | Power connector, analog input harness, subwoofer output connector, corner caps, USB cable, JL Audio badge, hex wrenches |
Frequently Asked Questions - VX600/1i JL Audio
User questions about VX600/1i JL Audio
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Receiver in PDF format for free! Find your manual VX600/1i - JL Audio and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VX600/1i by JL Audio.
USER MANUAL VX600/1i JL Audio
600W Monoblock Class D Subwoofer Amplifier with Integrated DSP
CONNECTION GUIDE
Thank you for purchasing a X Audio amplifier for your sound system.
Your amplifier has been designed and manufactured to exacting standards in order to ensure years of musical enjoyment. For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you decide to install the amplifier yourself, please take the time to read this manual thoroughly to familiarize yourself with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this manual or any aspect of your amplifier's operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance, please contact the JL Audio Technical Support Department at technikale@jlaudio.com or call (954) 443-1100 during business hours.
Installation Applications
This amplifier is designed for operation with 12 volt, negative-ground electrical systems. Using this product in systems with positive ground and/or voltages other than 12V may result in damage to the product and will void the warranty. This product is not certified or approved for use in aircraft.
Product Description
This is a monatlock, Class D subwoofer amplifier equipped with the second generation of JL Audio's NexD™ high-speed switching technology. It is engineered to deliver reference-grade audio amplification with outstanding efficiency and unprecedented, built-in processing power. Instead of traditional analog processing controlled by knots and switches, VSG amplifiers feature an integrated DSP (Digital Signal Processor). The amplifier and its integrated DSP are configured using an external device (IPC, Tablet or iPhone), with the appropriate JL Audio TUN™ application installed. (See What Is TUN™ section for more info.)
Planning Your Installation
It is important that you take the time to read this manual thoroughly and that you plan your installation carefully. It is very easy to damage expensive vehicle systems in modern automobiles. Never assume that you have found appropriate wics without consulting a reliable wiring diagram or without analyzing with proper test equipment. If you are uncomfortable or unfamiliar with reading diagrams or testing methods, please enlist the services of your authorized IT. Audio dealer to perform the installation. Your authorized dealer has the training expertise and installation equipment to ensure optimum performance from this product. The following are some considerations that you must take into account when planning your installation.
Safety Considerations
• Install your amplifier in a dry, well-ventilated location that
does not interfere with your vehicle's safety equipment.
air bags, seat belt systems, ABS brake system
- Do not mount the amplifier in the engine
compartment or in any areas of extreme heat.
- Security should the amplifier so that it does not call to loose in the event of a collision's rider-off or as a result
of repeated vibrations during normal operation.
- Check before drilling to make sure that you will not be drilling into
a fuel tank, gas/brake line, wiring harness, or other vital system.
- Do not run system wiring outside or underneath the
vehicle/vessel. This is an extremely dangerous practice,
which can result in severe damage/injury.
• Take the necessary precautions when making connections to the vehicle's battery.
- Project all system wires from sharp edges by carefully routing them.
wing them down and using rommets and loom where appropriate.
- Secure all wiring as needed, using cable ties or wire clamps
to protect them from moving parts and sharp edges.
Cooling Efficiency Considerations
The outer shell of your JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling performance, this outer shell should be exposed to as large a volume or air as possible. Enclosing the amplifier in a small, poorly ventilated chamber tan lead to excessive heat build-up and degraded performance. If an installation calls for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the ate of a tan. In normal applications, fan cooling is not necessary. If mounting the amplifier under a seat, make sure there is at least 1 inch (2.5 cm) of space above the amplifier's outer shell to permit proper cooling.
What is included
(1) A-ohing (1) Street Services
(1) Arolog Input Charter (1) Suboperator Output Connection
(1) JL Audio Badge (4) Corner Caps
(1) USB A/B Cable (6 ft/1.8 ml) [1] Corner Cap Tool
(2) Black Hex Cap Machine Series [1] 2.5 mm Hex Research
(2) Silver Transparence (1) 3 mm Hex-Church
JL Audio Badge
To complement the amplifier's mounting orientation, the logo badge includes a recessed key feature allowing it to be affixed at 90 degree increments on the amplifier's top. To install, remove the adhesive backing and press the badge at the desired orientation.
1 Power Connector
run 4 AWG power wire from the positive (1-12V) battery post to the amplifier mounting location. If additional amplifiers are being installed, run the appropriate gauge power wire for the combined maximum current draw, and install a fused distribution block near the amplifiers.
II. An appropriate fuse (sold separately) at the main power wire(s) is vital for vehicle safety. This fuse must be installed within 18 inches (45 cm) of the battery post connection. If this is the only device connected to this main wire, use a 50 A fuse. Do not install the fuse until the power wire has been securely connected to the amplifier.
c. The ground connection should be made to a clean, solid metal grounding point using 1 AWIC wire, and kept as short as possible. The metal surface at the grounding point should be sanded to create a clean, metal to metal connection. For optimal grounding, we recommend using a JL Audio ECS master ground lug (XB MGLU). All ground connections (source unit and amplifiers) should be made at the same location.
D. The remote connection should be made to the source unit's positive (+12V) remote turn on output. If your source unit does not have a dedicated remote turn-on output, consider one of the alternative turn-on options (See Turn-On Mode section for more info.)
2 Analog Input Harness
The Analog Input Harness accepts the following connections:
Line-Level Analog Inputs: Two female RCA jacks feed a differential-balanced input section, providing a high degree of input flexibility, and retaining superior noise rejection. This type of Input architecture also allows the V3600/11 to cleanly accept any analog audio signal up to 16 VRMS, without using a line-output converter.
Preamp Outputs: Two female, RCA jacks deliver line-level, analog audio outputs (Max 4V RMS); that are compatible with most types of aftermarket equipment. These are configured with the TuN® Software Interface.
Remote: This connection provides a positive (+12V) turn-on voltage (175 mA limit) to activate other aftermarket equipment (similar to an aftermarket head unit's remote turn-on lead).
Valet: When connected to negative ground, this connection activates the Valet. Mode Preset and will remain active until the ground connection is removed. This preset is configured using the TUN Software Interface and will override any DRC controlled preset.
Corner Cap Installation and Removal
The corner caps are designed to conceal the amplifier's mounting holes and hardware. To install, simply press a corner cap into each mounting hole. To avoid scratching the amplifier's chassis during removal, use the included, plastic corner cap tool and lift below each cap.
Making Connections
VXI amplifiers utilize removable plugs and harnesses to make the
following connections
• Power Connector and Subwoofer Output Connector
To connect the power, ground, remote turn-on and subscriber output wires to the amplifier, back out the set screws on each connector using the supplied hex wrenches. Strip back 3/8 inch (10 mm) of insulation from the end of each wire and insert the bare wire into the receptacle on the power connector plug, setting it firmly so that no bare wire is exposed. While holding each wire in place, tighten each set screw firmly, taking care not to stop the head of the screw. Install each connector by plugging it into the amplifier's corresponding receptacle, pushing firmly.
- Analog Input Harness
This harness includes connections for Signal Input (RCA plugs), Preamp Outputs (RCA plugs), Remote Turn-On Output (wire lead) and Voxel Input (wire lead). Select either the included black hex cap machine screws or the silver thumscrews to secure the Analog Input Harness connector to the amplifier.
Turn-On Mode
VXI amplifiers can be switched on and off using one of three methods, configured by the "Turn On Mode" setting in the TUR" Software interface. Refer to the table below for detailed info and decide which option is best suited for your specific system.
| Setting Mode Function Connection | ||
| Balance | Conventional (Pre-test) | True, correct confirmed by your current work. |
| DC Office | UC, Official Sampling charge | Automatically tests until the sampling process is presented at the DC designed in DDM and update. |
| Digital | Signal Sampling Charge | Automatically tests from the scanning of the DDM's output, which is also transmitted to the DDM, thus describing the input, performance, and output levels. |
3 Subwoofer Output Connector
Connect the subwoofer wires to the corresponding terminals.
4 JLid-COMM
Connect optional accessories (VX- BTC, VX-HUB, etc.) to this port.
5 JLid-CTRL
Connect optional DRC (Digital Remote Controller) wired controllers to this port.
6 SD + Reset
Lift the dust cover to access the following utility functions:
aset Buttons: Use a small pin to perform the following:
Reboot Amp Press and release the right button.
Factory Reset (wipe memory, reboot amp) - Press and hold the left
button for 7 seconds.
DFU (Device Firmware Update) Mode: Press and release both
Obligia S. Helmschukay.
Micro SD Slot: For service/future expansion.
7 USB
This USB A/B port permits connection to a computer for configuration and tuning, using the TUN® Software.
8 DIGITAL-In
Tosink port accepts 2 channel digital audio signal from any optical (S/PDF) digital output, with a sample rate up to 192 kHz.
9 DIGITAL-Out
Provides a digital audio output (24 bit/96 kHz) that is not susceptible to RF interference or noise generating electrical conditions. By default, this is a pass-through audio output, with no signal processing applied, and intended for use with other equipment that have an optical [Toslink] digital audio input (SPDIF) port. Using the TUN™ Software Interface, you may configure this output's routing, equalization, output level and ORC control functionality.
Wiring Diagram - VX600/11
Connections
| Pilot Connection | ||
| Connection Type Capacity (W) | Protein | |
| -12 VDC, 4.5V DC Positive/4.5V | AC Power Connection to Battery | |
| Ground (C, 4.5V) and 3.5V Signal input (DC) | DC Motor Field Control Connection | |
| Electrical 100V to 100V DC Positive | DC Motor Field Control Input from Power Source Unit | |
| Analog Input hardware | ||
| Label | Plug-Wire Color | Description |
| Input 1 White | ECA | Circuit input |
| Input 2 | Red ECA | Channel 2 Signal Input |
| Pre Output 1 | Red Load | Phased Cable Output 1 |
| Pre Output 2 | Red ECA | Phased Signal Output 2 |
| Revision | Blue | Proactive (7) 700 Turn On Output (20% 6x 10% 2) |
| Total | Green | Negative (GNC) Grid Input Instruction the United Code Transit |
| Substrate Output Component | ||
| Connection Type Capacity Description | ||
| SLAB | 1 to 10 WDCS | Positive Substrate Output |
| SLAB | 1 to 10 WMCs | Negative Substrate Output |
| Data Conclusions | ||
| Label | Type | Description |
| LED-COM | RFS Band | Optional supplementary connections (SWHC, WC-HUB, etc.) |
| JUL-CTA | RUS Band | Optional DRG 10 dual power source Control Set to connection |
| USB | USB Band | Computer and Network configuration using WiFi Software Interface |
| DIG-14-In | SDF Iner | 2-channel, optical Block & High Signal Input |
| DIG-14-Out | SDF Out | 2-channel, optical Block & High Signal Input |
| SD - Box | Fast Box | Global and Western Digital/Board Device / Immune Update motor |
| Micro-50 Tint | Not for future operation | |
Specifications
| Amplifier Specifications | ||||
| Amp Per Topology: 10000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 | ||||
| Power Supply: 8000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 | ||||
| Recommended Power/REF. Power: 1000 | ||||
| System transmitted Power: 25A | ||||
| Supply Current Power: 1kW | ||||
| Input Voltage Range: 200 mV 16V-18V | ||||
| Rated VDS Range: 14Ω, <14Ω-18Ω | 4000V±1 | 550W±1 | 550W±1 | |
| g±1Ω | g±1Ω | g±1Ω | ||
| Rated RMS Range: 125Ω, <125Ω-18Ω | 300W±1 | 400W±1 | 550W±1 | |
| g±1Ω | g±1Ω | g±1Ω | ||
| Adjusting Impedance: 275~280kHz(≤14~20kHz) | ||||
| Operating Power | Sub Output: (2 or lower), 25Hz in systemed (inferred) | 90 dB (independent to fixed power), (4 dB (independent to 1 Hz)) | ||
| Liquid Input | Sub Output: Sousightless, 25Hz in systemed (inferred) | 90 dB (independent to fixed power), (4 dB (independent to 1 Hz)) | ||
| Damping Factor: 125~50 Hz at 4Ω, <125~50 Hz at 2Ω | ||||
| DCP Specifications | ||||
| Processor: 1M DC/7.5L processing at 24 bit-15 MHz | ||||
| Operating Power | Total Load: 150W (systemed by fixed) | |||
| Number of Channels: 2 or higher measured threshold 42A parks | ||||
| pca: 10% Global tax cheese-mounted lock imp parts | ||||
| Liquid Output Capacity | 36 Capex Charge Rate: Up to 25% 10HZ/s | |||
| pca: 10% Level, 2 or higher measured threshold 42A parks | ||||
| Net Output Rate: 7 Pcs | ||||
| pca: 10% Global tax cheese-mounted lock imp parts | ||||
| Liquid Output Power | Per Output Time taken: 10 hrs time | |||
| Conditions | ||||
| Le WaR: 500mA, 100mA, 2.5A or 240mA, 180mA or 34mA | ||||
What is TUN?
TUN™ is software that you use to configure, tune and control your VXi amplifier, and other JL Audio DSP products. TUN™ automatically recognizes what it is connected to, and allows you to make adjustments with a clear interface specifically set up for that product. TUN™ is available for download for free in a variety of applications, for computers and most handheld devices. For more information, visit https://audio.com/tun
TEN.
For Windows® PC or Mac® computers, TiN® connects via USB and offers complete control and command of the entire VXi feature set from the comfort of your desk or driver's seat. Software also runs in demo mode, without connected amplifiers, for offline setup or demo purposes. Test drive it for free!
TuN. | Mobile
For iPad or Android tablets. Enjoy the full-featured TufN ™ software experience on your tablet, with the freedom of a wireless connection via Bluetooth ™ . Requires VXI-BTC Bluetooth ™ Communicator.
TcN, Express
Wireless connection and streamlined options, for fast and simple amplifier setup. Download TGV® Express for iPhone, iPad and Android phones & tablets. Requires VXI-BTC Bluetooth® Communicator.
Limited Warranty - Amplifiers (USA)
It is also worried this product to be free of defects in materials and understandability for a period of two (2) years from the original date of purchase. This warranty is not transformative and applies only in the entire pursuant form an authorized it is also worried. Should service for necessary under this warranty for any reason due to manufacturing defect or manufacture, it is will not be discontinued; repair or replace the defective product with new or remanufactured product or no charge. Damage caused by the following: an increased under warranty, accident, misuse, abuse, product modification or defect, failure to follow installation instructions, unambridged repair attempts, misrepresentations by the action. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or restructuring the unit(s). Cosmetic damage due to accident or normal cause and loss is not covered under warranty.
Warranty is void if the product's serial number has been removed or defaced. Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, that apply to this product the center. Some states do not allow limitations on implied warranties therefore these exclusions may cut apply in you. This warranty gives you useful legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product.
All warranty returns should be sent to J. Audio's Amplifier Service Facility freight-secured Through an instrument J. Audio dealer and must be accumulated by proof of purchase a copy of the original sales receipt. Since, returns from consumers or non-authorised dealers will be refund unless explicitly attributed by J. Audio with a valid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Non-authorised items received will be returned freight-reelief. Customer is responsible for whasking changes and insurance in sending the product to J. Audio Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
UL Audio Customer Service
(95-1) 4:13-1100 9:00 AM - 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10,69 North Commerce HKY, Al-Final, TL 59,25
International Warranties:
Products purchased outside the United States of America are covered only by that country's distributor and not by IL Audio, Inc.
- Installation Applications
- Product Description
- Planning Your Installation
- Safety Considerations
- Cooling Efficiency Considerations
- What is included
- JL Audio Badge
- Power Connector
- Analog Input Harness
- Corner Cap Installation and Removal
- Making Connections
- - Analog Input Harness
- Turn-On Mode
- Subwoofer Output Connector
- JLid-COMM
- JLid-CTRL
- SD + Reset
- USB
- DIGITAL-In
- DIGITAL-Out
Brand : JL Audio
Model : VX600/1i
Category : Receiver