E-Laptop - Alarm system Godrej - Free user manual and instructions

Product Type	Electronic Safe (Laptop Safe)
Brand	Godrej
Model	E-Laptop
Category	Alarm System / Safe
Dimensions (H x W x D)	200 mm x 420 mm x 370 mm
Weight	12 kg
Volume	23 liters
Power Supply	4 x 1.5V AA alkaline batteries
Lock Type	Electronic keypad with motorized locking
Number of Bolts	2 solid steel bolts
Code Length	3-6 digits (user selectable)
Default Personal Code	1234
Default Master Code	800000
Auto Lockout	After 4 consecutive wrong attempts (0, 15, or 30 min delay)
Low Battery Indicator	Yes ("bA-LO" displayed)
Emergency Override	Manual key override (2 keys included)
Non-Volatile Memory	Yes (code not erased on low battery)
Interior Carpet	Yes
Mounting	Floor, wall, or wardrobe with anchoring bolts (included)
Package Contents	Safe, warranty card, user manual, anchoring bolts, 2 override keys
Country of Origin	India (Godrej & Boyce Mfg. Co. Ltd.)

Frequently Asked Questions - E-Laptop Godrej

What is the default personal code?

The default personal code is 1234. It is recommended to change it as soon as possible for security.

How do I change the personal code?

Open the safe, press CLEAR twice (display shows PROG), press 68 LOCK (display shows NEU), enter your new code and press LOCK. The safe will close. The new code is now set.

What is the master code and how do I change it?

The factory master code is 800000. To change: open safe, press CLEAR twice (display shows PROG), enter original master code (display shows NEU), enter a 6-digit new code (display shows AGAIN), re-enter code and press LOCK. Display shows DONE on success.

What do I do if I forget my personal code?

You can use the emergency override key to open the safe. Insert the key into the cylinder (after removing the Godrej plate) and turn clockwise. Then set a new personal code while the door is open.

How do I replace the batteries?

Open the safe (use override key if batteries are dead). Remove the battery cover screw on the back panel. Replace with four 1.5V AA alkaline batteries. Dispose old batteries properly.

What does 'ERROR' mean?

'ERROR' indicates an incorrect personal code. After 4 consecutive errors, the keypad locks out for a set duration (0/15/30 minutes). If locked out, wait or use override key.

What does 'HOLD 15' mean?

'HOLD 15' means the safe is in lockout mode for 15 minutes (or 30 if set). Press any key to see remaining time. You can use the override key to bypass the lockout.

How do I stop my code from displaying on the screen?

Open safe, press CLEAR twice (PROG appears), wait for PROG to disappear, then press 751019 within 5 seconds. A 6-digit code appears; press 0 then LOCK three times. The display will go blank. Now only dashes appear when entering code.

How do I set the automatic lockout delay?

Access programming: open safe, press CLEAR twice (PROG), press 751019. The 3rd digit of the 6-digit code controls lockout delay: press 0 (no delay), 1 (15 min), or 2 (30 min). Default is 1.

What should I do if I see 'ERROR1' or 'ERROR2'?

'ERROR1' means bolts failed to retract: push door inward while entering code. 'ERROR2' means bolts failed to extend: safe may be overstuffed, press door closed fully. If still issues, call GSS at 1800 209 9955.

USER MANUAL E-Laptop Godrej

Please fill your details below for future reference.

Date of purchase: ____

Product model:

Name & address of Distributor/Dealer: ____

Distributor phone number: ____

FOR SAFETY, PLEASE READ THIS MANUAL PRIOR TO USE.

SECURITY SOLUTIONS

Godrej & Boyce Mfg. Co. Ltd.

Gorej Security Solutions

Regd. Office: Plant No. 17, Pirojshanagar, Vikhroli, Mumbai 400 079

Tel: [phone] Fax: [phone]

Toll-free: 1800 209 9955 | SMS'GSS' to 53636 | Email: [e-mail] | Visit: www.godrejsecure.com

In view of the Godrej policy of continuous development and improvement, the dimensions and specifications may be changed without prior notice or obligation. The colours of the product in leaflet may not match the actual colours due to printing limitations.

An ISO 9001:2015 | BS OHSAS 18001:2015

Products Marketed and Serviced By Godrej & Boyce Mfg. Co. Ltd.

E-LAPTOP

User Instructions

Exterior view of a gray LAPTOP safe with a digital display and control panel, surrounded by binary code patterns (no readable text)

Be Intelligent. Be Safe.

E-LAPTOP SAFE

Attractive design, suitable for use in apartments and offices. Utilising a proven and reliable electronic circuit with embedded technology.

Height x Width x Depth:

200mm × 420mm × 370mm

Weight: 12 Kgs Volume: 23 Ltrs

Batteries:

Four 1.5Volts AA Size Alkaline

Exterior view of a silver safe with an open door and internal compartments (no visible text or symbols)

SPECIAL FEATURES

Auto freeze after four consecutive wrong attempts

Low battery indicator

Compact with attractive aesthetics

Interior carpet

Motorised override in case password is forgotten

Non Volatile memory prevents password erasure, when the battery is low

Features

1 Motorized Locking
2 One Piece moulded keypad
3 Durable Finish
4 Two Solid Steel Bolts
5 Enhanced Battery Life
6. Non Volatile memory prevents password erasure,

when the battery is low

7 Automatic Lockout after four consecutive wrong password entries
8 Emergency Manual Key Override
9 3-6 digit personal code

PACKAGE CONTENTS

Safe

Warranty Card

User Manual

Anchoring Bolts

Override Keys

TOOLS REQUIRED

Drill Machine

Spirit Leveler

Drill Bit

Mallet

Spanner

Note: Not included in the package contents.

*To grout/mount the safe

GROUTING PROCESS

1

Diagram of a device with an arrow pointing to a component, showing no text or symbols.

Using sprit leveler, check if the safe is evenly placed on the ground or against the wall or inside the wardrobe (depending on where it is to be grouted). If not, choose a different location for grouting.

2

Diagram of a box with a magnified inset showing a small object inside (no text or symbols)

Sprit leveler lets you know precisely if the safe is evenly placed.

3

Diagram showing two magnified views of a mechanical component with no visible text or symbols

Through the holes inside the safe, make markings on the ground or the wall or inside the wardrobe.

4

Diagram showing a light ray interacting with a screen, mounted on a grid surface (no text or symbols)

Drill holes into the ground or the wall or the inside of the wardrobe.

5

Fix the safe by hammering the anchoring bolts (provided in the kit) through the holes.

6

Tighten the anchoring bolts with a spanner.

IMPORTANT INSTRUCTIONS

• Please keep this manual and override keys in a safe place (NOT INSIDE THE SAFE)
• DO NOT use any liquid while cleaning the keypad, you could use a damp cloth if required
  • Make sure the safe is anchored properly as it can fall and hurt people and property
• DO NOT place any liquid on top of the safe, a spill on the keypad may render the safe inoperable
  • DO NOT overstuff the safe or you can damage the motor mechanism or the contents
  • DO NOT open the back cover or try to repair the safe yourself. In case of any problem contact GSS call center at 1800 20 999 55

OPERATION

1. To open the safe: Enter personal code. When the display shows "OPEN", the bolts will retract automatically. After bolts have fully retracted, the display will show "OPENED". Now, open the door by pulling from the bottom of the keypad.
2. To lock the safe: Close the door and press LOCK button. The display will show "CLOSE", the bolts will extend automatically. After bolts have fully extended, the display will show "CLOSED".

Note: Master code can only be used to unlock the safe.

TO CHANGE THE PERSONAL CODE

1. Open the safe.
2. Press CLEAR twice, display will show "PROG".
3. Press 68 LOCK, display will show "NEU".
4. Enter the new code and press LOCK. Safe will close.

Note: Default Personal Code is "1234"

TO CHANGE THE MASTER CODE

1. Open the safe.

2. Press CLEAR key twice, display will show "PROG", then enter original master code. The factory set master code is 800000. Then the display will show "NEU".

3. Enter the 6 digit code you desire, the display shows "AGAIN", then enter the code again and press LOCK key to confirm.

4. The display will show "DONE" to indicate new master code has been set up successfully.

WARNING:

For security purposes, you should change the factory default code as soon as possible. Godrej Security Solution shall not be responsible for only theft caused by such negligence.

TO STOP YOUR CODE FROM BEING DISPLAYED

1. Open safe using your Personal Code.
2. Press CLEAR twice, the display will show "PROG".
3. When "PROG" disappears, press 751019 within 5 seconds.
4. 171301 will appear, with the first digit flashing, press (0) then press LOCK thrice. The display will go blank.
5. Close the safe (you will have to press your Personal code to lock door).
6. By entering personal code, check if this feature is activated. You will see that “---” will appear instead of your personal code.

If your lock is set so that your code appears and you need it to not appear one time, you can press (0) then LOCK key before your code. Only dashes will appear for that one time. The next time you press your code it will appear as usual.

Likewise, if your lock set up so that your code does not appear, you can press (9) then LOCK and your code will appear for that one time only.

This function applies to both modes (Home mode & Hotel mode.)

TO ACCESS THE PROGRAMMING

• Open the safe.
• Press CLEAR twice, the display will show "PROG".
• Press 751019 while the word "PROG" disappears.
• A 6-digit code will appear on the screen with the first digit blinking. This code denotes the current setup for the safe.
  • Each of the 6 digits corresponds to one section of the programming as explained in detail below.
• In order to change the programming setup, the correct digits have to be entered at the correct positions.

To set up the different features listed below, you must first decide how you want the safe to function.

Section (a) (1st Digit) Code appearance on display

Press 0: If you DO NOT want your code to appear on the display (only dashes will appear) with beep sound when you press each key button. (Default)

Press 1: If you want your code to appear each time you press your code and then will flash your code for verification one time. Beep sound when you press each key button.

Press 2: If you want your code to appear each time you press your code, with beep sound when you press each button.

Section (b) (2nd Digit) Preferred number of digits in your code

Press 3: To use a 3-digit code.

Press 4: To use a 4-digit code.

Press 5: To use a 5-digit code.

Press 6: To use a 6-digit code.

Press 7: To choose the length of code (3-6 digits) when you set the code. (Default)

Section (c) (3rd Digit) Lockout delay

If the wrong code is entered 4 times in a row, the keypad will shutdown for a length of time that you set.

This is to deter someone from opening your safe by trying random number. You must pick one of these three options:

Press 0: For no lockout delay.

Press 1: For a 15 minute delay. (Default)

Press 2: For a 30 minute delay,

The master code will open the safe if you lose the code and override keys. The master code is preset at the factory.

Press 2: To turn OFF the master code feature.

Press 3: To turn ON the master code feature. (Default)

Section (e) (5th Digit) Audit trail

Keep default code "0" as the safe does not support this feature

Section (f) (6th Digit) Operational mode

Keep default code "0" as the safe does not support this feature

Note: The Factory default setting is "071300"

TESTING AND REPLACING THE BATTERIES

Test battery level:

Battery levels can be tested either with the door opened or closed

Press LOCK key. The display will show "bA-HI" or "bA-LO". "bA-LO" means that you need to replace the batteries.

Replacing the Batteries:

1. Open the Safe using your personal code. If the batteries are dead, use the Emergency Override key.
2. Remove the battery cover on the back panel by unscrewing the Phillips screw.
3. Remove all four used batteries.
4. Replace the batteries with four 1,5V AA size alkaline batteries.
5. Put back the battery cover.
6. Dispose the used batteries in an environment friendly way.
7. Put back the Phillips screw to secure the battery cover.
8. Keeping the door open, test the safe to make sure it works.

EMERGENCY OVERRIDE KEY

1. Using the supplied Allen key unscrew one of the screws holding the Godrej plate and rotate to expose key cylinder.
2. Using one of the override keys, insert into the cylinder and turn clockwise to open the safe.
3. While the door is open and the key is still turned, follow the instructions to set your personal code.

Note: When you set the new personal code, rotate the key to the locked position, so that it can be removed. If you get an error message, wait until the motor stops moving and then turn the key back to locked position and remove it. Your new personal codewill still remain.

WARNING:

Keep the override keys in a safe place other than inside this safe. These keys are to be used in emergencies.

ERROR MESSAGES

Listed below are error codes you might encounter:

ERROR This means that you have pressed an incorrect personal code. Verify your personal code and try again. If you get this error four times consecutively, the keypad will lock out for 0/15/30 minutes.

HOLD 15 This means the safe has entered the lockout period. You will not be able to open the safe during the lockout period. By pressing any key during this period you can see how much time is left until the lockout is over. If your personal code still doesn't work, use the override keys to reset the safe. (see "TO ACCESS THE PROGRAMMING" section 3)

ERROR1 This means that the bolts failed to retract fully. Press the door towards the inside while entering your personal code. If you still cannot open your safe then contact GSS call center on 1800 20 999 55

ERROR2 This could also mean that the bolts failed to extend fully. Most likely because the safe is too full. Press the door to close it fully while pressing your personal code. If you still cannot close your safe then contact the GSS call center on 1800 20 999 55.

INFORMATION ON E-WASTE HANDLING AND MANAGEMENT

Dear Customer,

The Ministry of Environment and Forests have published The E-waste (Management and Handling) Rules 2010 which comes in effect from 1st May 2012.

E-waste is defined as any electrical or electronic component of products in whole or in part, or rejects from their manufacturing or repair process which are intended to be discarded.

These rules apply to every producer; consumer or bulk consumer involved in the manufacture, sale, and purchase and processing of electrical and electronic equipment or components as specified in Schedule 1 (please refer to our website www.godrej.com in the 'Good & Green' section of CSR module for more details).

Under these rules, specific roles and responsibilities are defined for producers, consumers and recyclers handling and managing e-waste.

E-waste is to be managed in an environmentally sound manner which means, taking steps to ensure that health and environment are protected from adverse effects of hazardous substance contained in such wastes.

Rule 6 of the E-waste (Management and Handling) Rules 2010 states that bulk consumers of electrical and electronic equipment shall be responsible for recycling of the e-waste generated by them. Bulk consumer means bulk users of electronic and electrical equipment such as Central Government or State Government Departments, public sector undertakings, banks, educational institutions, multinational organizations, international agencies, private companies that are registered under the Factories act 1948 and Companies act 1956. The bulk consumers have to ensure that the e-waste generated by them is channelized to authorized collection centers or is taken back by the producers. They shall maintain records of e-waste generated by them in Form 2 and make such records available for scrutiny by the State pollution control or the Pollution control Committee concerned.

All consumers of electrical and electronic equipment irrespective of their status as bulk consumers or not, shall ensure that e-waste generated by them is channelized to authorized collection center(s) or registered dismantler(s), or recycler(s) or is returned to the pick-up/take back services provided by the producers. (Please refer to our website www.godrej.com in the 'Good & Green' section of CSR module for more details).

All our products intended to be recycled under the category of e-waste (as defined above) carry a label or stamp of the WEEE symbol (A wheelle bin with a cross), which states that it falls under the hazardous waste category and is not to be disposed along with normal garbage.

We seek your support in ensuring environmentally sound management of e-waste and aid us in sustaining our earth's natural resources and maintaining the earth's green cover intact for the benefit of our future generations.

NOTES

NOTES

NOTES

NOTES