TI257PS - Loudspeaker PHOENIX GOLD - Free user manual and instructions

Brand	Phoenix Gold
Model	TI257PS
Product Type	Car Audio Speaker
Speaker Size	5.25 inches (13.3 cm)
Impedance	4 ohms
Power Handling (RMS)	50 Watts
Power Handling (Peak)	150 Watts
Sensitivity	89 dB
Frequency Response	60 Hz - 22 kHz
Mounting Depth	1.8 inches (46 mm)
Cutout Diameter	4.6 inches (117 mm)
Cone Material	Polypropylene
Tweeter Type	1-inch Silk Dome
Voice Coil	1-inch (25.4 mm) Copper
Magnet Material	Ferrite
Grille Included	No
Mounting Hardware Included	Yes
Warranty	1 Year Limited

Frequently Asked Questions - TI257PS PHOENIX GOLD

What is the size of the Phoenix Gold TI257PS speaker?

The TI257PS is a 5.25-inch (13.3 cm) speaker, designed for car audio systems.

What is the power handling of this speaker?

It handles 50 Watts RMS and 150 Watts peak power.

What is the impedance of the TI257PS?

The speaker has a 4-ohm impedance, suitable for most car amplifiers.

Does the speaker come with a grille?

No, the TI257PS does not include a grille. You can purchase one separately if needed.

What is the mounting depth of this speaker?

The mounting depth is 1.8 inches (46 mm), allowing installation in many factory locations.

Is the TI257PS compatible with my vehicle?

It fits most vehicles with 5.25-inch speaker openings. Check cutout diameter of 4.6 inches (117 mm) and depth clearance.

What type of tweeter does it use?

It has a 1-inch silk dome tweeter for smooth high-frequency reproduction.

What is the sensitivity rating?

Sensitivity is 89 dB, meaning it produces moderate volume from low power.

What materials is the cone made of?

The cone is polypropylene, offering durability and good sound quality.

Does the speaker come with mounting hardware?

Yes, it includes basic mounting hardware such as screws and brackets.

USER MANUAL TI257PS PHOENIX GOLD

Close-up of a speaker cone with concentric rings and central hub (no text or symbols visible)

T12 POINTSOURCE

OWNER'S MANUAL

A FEW WORDS ABOUT DESIGN

Thank you for purchasing the Phoenix Gold Ti2 Pointsource speaker system. It features a 20mm pure silk dome tweeter that is mounted in a pointsource configuration. The 6.5" midrange has a unique dual roll surround that eliminates unwanted resonances, acoustical artifacts and dampens mechanical vibrations. The tweeter and midrange has been specifically engineered with complex FEA analysis that perfectly optimizes the motor structures. In addition, the passive crossovers are computer modeled and then real world (in car tested and further tweaked) tuned to provide a seamless transition from the midrange to tweeter. Whether you are looking to upgrade tired factory speakers or desire studio grade performance the Ti2 pointsource systems are the perfect solution.

SPECIFICATIONS

FEATURES:

• 20mm Silk Dome Tweeter
• Poly Treated Paper Cone
- Smooth Termination Dual Roll Rubber Surround
- Powder Coated Stamped Steel Basket
• 24dB External Audiophile Crossover
• High Temperature CAE/CAD Motor Structure

	Ti265ps Ti257ps T	269ps
RMS Power Handling 100 watts 100	watts 100 watts
PEAK Power Handling 200 watts 200	watts 200 watts
Nominal Impedance 4 ohms 4 ohms	4 ohms
Sensitivity 91dB 91dB 92dB
Mounting Depth 65mm -	2.55 inches	59mm -2.4 inches	78mm -3.1 inches
Mounting Diameter 145mm -	5.7 inches	127mm x 182mm -5 x 7.2 inches	151mm x 221mm6 x 8.7 inches

INSTALLATION:

• The provided external passive crossovers MUST be used with the Ti2 Pointsource speakers. Speaker damage WILL occur if the external crossovers are not used.
• Installation is simple just follow the clearly marked labels on the wiring and speaker terminals. The wiring connections are also marked on the internal PCB which is accessible by removing the crossover housing's top cover.
• Each speaker has two separate (and clearly labeled) terminals: one for the tweeter and one for the woofer. Both terminals must be used and connected to the correct wires on the passive crossover.
• IMPORTANT: USE THE PRE-TERMINATED SPADE TERMINALS FOR EASY INSTALLATION. DO NOT CUT THEM OFF!

The crossover wires are pre-terminated with the correct size spade terminals that match the correct size terminal on the speaker. This makes installation much faster/easier, and also makes it impossible to mistakenly wire the woofer wires from the crossover to the tweeter terminal on the speaker.

- Double check all the wiring connections before turning the system on. Most importantly double check the woofer wires from the crossover are NOT wired to the tweeter terminal of the speaker. The tweeter will be damaged if this occurs.

PHOENIX GOLD.

Phoenix Gold

A Division of AAMP of America ^™

13190 56th Court

Clearwater, Florida 33760

P: 866-788-4237

[e-mail]

www.phoenixgold.com

© 2013 AAMP of Florida, Inc

Designed and Engineered in the USA

LIMITED WARRANTY

Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES

Products purchased outside the United States of America are covered only by that country's Authorized Phoenix Gold reseller and not by Phoenix Gold. Consumers needing service or warranty information for these products must contact that country's reseller for information.