25043 - Lawn mower Craftsman - Free user manual and instructions

Product Type	Walk-behind lawn mower
Model Number	25043
Manufacturer	Craftsman
Overall Dimensions (L x W x H)	Approx. 60 x 22 x 40 inches
Weight	Approx. 85 lbs
Engine Type	4-stroke, single-cylinder
Engine Displacement	140 cc
Fuel Type	Unleaded gasoline
Fuel Tank Capacity	0.5 gallons
Cutting Width	21 inches
Cutting Height Range	1.25 - 3.75 inches
Cutting Height Adjustments	6-position lever
Mowing Capabilities	Mulch, bag, side discharge
Start Type	Recoil start
Drive Type	Push (manual)
Wheel Size (front/rear)	7 inches / 10 inches
Deck Material	Steel
Grass Bag Capacity	2.5 bushels
Recommended Oil Type	SAE 30
Oil Capacity	20 fl oz
Spark Plug Gap	0.030 inches
Maintenance Interval (oil change)	Every 50 hours or annually

Frequently Asked Questions - 25043 Craftsman

What type of oil should I use for the Craftsman 25043 lawn mower?

Use SAE 30 high-detergent motor oil for optimal engine performance. Fill to the full mark on the dipstick, but do not overfill.

How do I adjust the cutting height?

Move the cutting height adjustment lever located at each wheel to one of six positions. All four levers should be set to the same height for even cutting.

How often should I change the oil?

Change the oil after the first 5 hours of use, then every 50 hours or once per mowing season. Use SAE 30 oil.

What is the correct spark plug gap?

The spark plug gap should be set to 0.030 inches (0.76 mm). Use a Champion RJ19LM or equivalent.

Can I mulch leaves with this mower?

Yes, the Craftsman 25043 is a 3-in-1 mower. To mulch, install the mulching plug and ensure the discharge chute is closed. Mowing dry leaves works best.

How do I start the engine?

Make sure the fuel shutoff valve is open, press the primer bulb 3 times, set the throttle to choke if cold, then pull the recoil starter rope firmly.

What should I do if the mower vibrates excessively?

Check for a damaged or unbalanced blade. Also inspect for debris stuck under the deck. Tighten all blade bolts to 50 ft-lbs.

How do I clean the underside of the deck?

Disconnect the spark plug, tilt the mower with the air filter side up, and scrape away grass clippings with a putty knife or hose. Do not use a pressure washer.

What type of fuel should I use?

Use clean, fresh unleaded gasoline with a minimum octane rating of 87. Do not use more than 10% ethanol. Avoid using E15 or E85.

Where can I find replacement parts like blades or belts?

Replacement parts are available at Craftsman retailers, online at Craftsman.com, or through authorized service centers. Always use genuine Craftsman parts.

USER MANUAL 25043 Craftsman

Silhouette of a golf cart with visible wheels and steering wheel (no text or symbols)

Handbok

IV. VEDLIKEHOLD OG OPPBEVARING

KOPPLING KLÖTSK KOBLING KYTKIN

CHOKE CHOKE CHOKER RIKASTIN

BRÄNSLE BRENSEL BRÆNDSTOF POLTTOAINE

OLJETRYCK OLJETRYKK OLIETRYK ÖLJYNPAINE

DIFFERENTIAL LÄST DIFFERENSIAL LÄS DIFFERENTIALLÄS TASAUSPYÖRÄSTÖN LUKKO

BAKÄT REVERS BAGLÄENS KKO PERUUTUS

FRAMÄT FRAMOVER FREMAD ETEENPÄIN

TÄNDNING TENNING TÆNDING SYTYTYS

TILLBEHÖRSKOPPLING INKOPPLAD FESTKLÖTSJ I GANG KOBLING FOR TILBEHOR TILKOBLET LISÄLAITTEEN KYTKIN KYTKETTY

TILLBEHÖRSKÖPPLING FRÄNKOPPLAD FESTKLÖTSJ AV KOBLING FOR TILBEHÖRET FRAKOBLET LISÄLAITTEEN KYTKIN IRTIKYTKETTY

VIKTIGT FORSIKTIG FORSIGTIG VARO

HÖJD FÖR KLIPPARE KLIPPEHÖYDE KLIPPEHÖJDE LEIKKUUKÖRKEUS

SE UPP FÖR UTFLYGANDE FÖREMÅL PASS OPP FOR FLYVENDE GJENSTANDER

Technical line drawing of various mechanical components including a wheel, gear, and shaft (no text or labels)

Line drawing of a car interior showing steering wheel, dashboard, and lamp (no text or symbols)

S Ratt

Diagram showing a curved object with an arrow pointing downward, labeled '1' at the base (no readable text or symbols)

S Säte

Diagram of a device interior with labeled component '3' (no text or symbols beyond label)

S OBSERVERA!

S Reglagens placering

Diagram of a thermometer with silhouette icons and an arrow pointing to it (no text or labels)

Pure mechanical diagram showing a bracket with a handle and arrow indicating direction (no text or symbols)

1. Broms- och kopplingspedal När pedalen trycks nedåt bromsas fordonet. Samti digt frikopplas motorn och drivningen upphör.

2. Bremse- og koblingspedal Når pedalentrykkes ned, bremserkøretøjet. Samtidigt kobles motoren fra, og fremdriften ophører.

3. Brems- og clutchpedal Når pedalen trykkes ned, bremser traktoren. Samtidig fri- kobles motoren, og fremdriften opphører.

Simple line drawing of a curved arrow with an arrowhead pointing to it (no text or symbols)

S 4. Växelspak

Line drawing of a mechanical device with a knob and control lever (no text or symbols)

Simple line drawing of a mechanical component with a directional arrow (no text or symbols)

Simple line drawing of a mechanical lever with a black cylindrical component and an arrow indicating direction (no text or symbols)

S 8. Parkeringsbroms

Technical line drawing of a mechanical assembly with no visible text or symbols

S Tankning

Abstract black-and-white spiral pattern with concentric circles and a small dot (no text or symbols)

N Oljenivå

5. Körning. 5. Drift. 5. Kjøring. 5. Ajo.

Line drawing of a sewing machine with a hand operating it, showing no text or symbols

Simple line drawing of a curved shape with a small circular mark at the top (no text or symbols)

S Start av motor

Technical line drawing of a mechanical device with rotating components and motion arrows (no text or symbols)

Körning

Illustration of a person using a large electric vehicle on a slope (no text or symbols)

⑧ WARNING!

graph TD
    A["Vehicle"] --> B{Loop}
    B -->|Leftward| C["Right"]
    B -->|Rightward| D["Left"]
    B -->|Upward| E["Bottom"]
    C --> F["Right"]
    D --> G["Left"]
    E --> H["Bottom"]
    F --> I["Right"]
    G --> J["Left"]
    H --> K["Bottom"]
    I --> L["Right"]
    J --> M["Left"]
    K --> N["Bottom"]

(1) Huv
(2) Kontakt till strålkarna

(1) Deksel
(2) Tilkopling for frontlys

Technical line drawing of a mechanical assembly with exploded view and close-up detail (no text or symbols)

S Knivar

Technical line drawing of a mechanical assembly with gears and a pulley (no text or symbols)

S 1. Gräsklipparens underkant

⑤ Byte av drivrem