PLCM7800 - Rear Camera Pyle - Free user manual and instructions

Product Type	Rear View Camera
Brand	Pyle
Model	PLCM7800
Dimensions (approx.)	2.5 x 1.5 x 1.2 inches (without bracket)
Weight	0.2 lbs (90 grams)
Power Supply	12V DC (vehicle battery)
Power Consumption	< 0.5W
Video Output	Composite RCA (1.0Vp-p, 75 Ohm)
Image Sensor	1/3-inch CMOS
Resolution	720 x 480 pixels (NTSC)
Viewing Angle	170 degrees (diagonal)
Night Vision	IR LEDs, effective up to 15 feet
Waterproof Rating	IP68 (submersible up to 1 meter)
Mounting Type	License plate bracket or surface mount
Parking Guidelines	Adjustable on-screen guidelines
Mirror/Reverse Image	Selectable (normal or mirror)
Operating Temperature	-4°F to 140°F (-20°C to 60°C)
Installation	Hardwired or plug-and-play with extension cable
Maintenance & Cleaning	Wipe lens with soft dry cloth; avoid abrasive cleaners
Safety Precautions	Secure all cables to prevent snagging; use properly rated fuse
Spare Parts & Serviceability	Camera unit is sealed; no user-serviceable parts inside

Frequently Asked Questions - PLCM7800 Pyle

How do I connect the Pyle PLCM7800 camera to my monitor?

Connect the yellow RCA cable from the camera to the video input of your monitor. The red wire provides 12V power, typically connected to your reverse light circuit. Black wire is ground.

Is the PLCM7800 compatible with my car's existing radio/navigation system?

It is compatible with any monitor or head unit that has a composite RCA video input. Many aftermarket stereos have this input. For factory systems, you may need an adapter.

What voltage does the camera need?

The camera operates on 12V DC from your vehicle's electrical system. Do not connect to 24V systems without a step-down converter.

Can I use this camera as a front-view camera?

Yes, you can use it as a front camera by connecting the power to an accessory source (e.g., ignition). The image will be normal (non-mirrored).

Is the camera water-resistant?

Yes, it has an IP68 rating, meaning it is protected against immersion in water up to 1 meter deep. It can withstand rain and car washes.

How do I adjust the parking guidelines?

The camera has a small toggle switch on the cable (or inside the housing) to turn guidelines on/off or adjust their angle. Refer to the manual for exact location.

The image is reversed/mirrored. How do I change it?

Many models have a 'mirror' switch on the camera cable that flips the image. If not, you may need an inline video processor or select the correct setting on your monitor.

What type of cable is included?

Typically a 12-foot (approx.) RCA composite cable with power leads. Extension cables are available separately for longer runs.

My camera stopped working. What should I check?

First check the power connection (12V). Use a multimeter to verify voltage. Then inspect the RCA connection and ensure the monitor is set to the correct input. The camera itself is sealed and not user-repairable.

Does the camera work at night?

Yes, it has infrared LEDs for night vision. It provides a clear black-and-white image in low light, effective up to about 15 feet.

USER MANUAL PLCM7800 Pyle

Blue remote control panel with a person riding a bicycle on a paved surface, alongside a black cable with colored wires and connectors (no text or symbols visible)

PLCM7800

Backup Camera & Mirror Monitor System

Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer's warranty. The installation instructions do not apply to all types of vehicles, and are written as guidelines to assist in installing the system. Please consult an experienced technician if you are not comfortable installing the product. Prior to using and installing the Backup Camera System, please read the safety information provided in this user manual. Be sure to use the product as outlined in this user manual. Altercation or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.

WARNING: Failure to read and follow these warnings and instructions may result in serious injury, including damaged property, so please pay close attention and exhibit the utmost care.

• The Digital Backup Camera is designed as an aid to the driver in detecting potentially hazardous driving conditions, obstructions, and large stationary objects. You, the driver, must also remember to drive safely and properly. Use of the Digital Backup Camera is not a substitute for safe, proper and legal driving practices.
• Never back up while looking only at the screen. You should always check behind and around the vehicle when backing up just as you would if the vehicle did not have the Digital Backup Camera. Always make sure your driving area is clear. Always back up slowly and with caution.
• Never depend on the Backup Camera entirely when backing up. The image on the screen is different from actual and real-time conditions. Objects viewed in the rear view monitor differ from actual distances because a wide-angle lens is used. So use the camera as an aid and always follow intended driving practices to properly judge distances from objects.
• The Backup Camera's assisted low lux lighting performance feature is also an aid to a driver. Always use your own eyes to confirm the vehicle's surroundings, as the displayed image may be not well lit or not entirely visible. Always proceed with caution and perform double-checks before proceeding.
• The area displayed by the Backup Camera is limited. It does not display objects that are close to or just below the bumper, underneath the vehicle, or objects out of the camera's view. The camera's view can change according to your vehicle's orientation on the road or changing road conditions.
• Be sure to always check the camera is properly functioning, is properly positioned and securely mounted.
• Make sure your trunk or hatch operates correctly, as intended, before and after installation.
• Proceed with caution when cleaning your vehicle around the camera. Avoid excess water exposure around the camera especially with spraying or a power washer.
• Please make sure to keep the camera clean and unobstructed from any debris
• Follow all traffic laws and motor vehicle regulations.
• Consult local laws and regulations for any restrictions on installation or use.
• Using a Backup Camera System is not adequate enough to completely eliminate a vehicle's blind spot. Always remember to drive with caution, following all traffic laws.

System Installation and Wiring

Camera System installation on diesel vehicles may require a slightly different wiring install. These installation instructions do not apply to all types of vehicles. They are meant only as a general guide due to the large number of vehicle makes and models. Consult your local motor vehicle laws on the use of this product to be sure it is permitted. Through installation of this backup camera system, you should be sure as to not degrade, damage or compromise the safety of any system or device on your vehicle. Improper installation and wiring of the vehicle back-up camera system may damage the vehicle's electrical system, including vital vehicle computer and operating systems. That could lead to an accident or fire, causing property damage and/or serious personal injury. It is highly recommended to seek professional installation advice from a qualified auto electrician or, in the alternative, to have the installation performed by a qualified auto electrician.

Please ensure that your monitor is secured and mounted where it would NOT obstruct any OEM vehicle safety features. In an event of an accident, manufacturer is not responsible for bodily injury caused by the monitor being a projectile. Select location for mounting the monitor in desired location. Ensure monitor location will not obstruct your vision while driving. The manufacturer assumes no liability for damage caused to your vehicle due to improper installation or use.

Caution: This unit is designed to operate on a 12V/24V DC NEGATIVE GROUND electrical systems. Connecting to other types of electrical systems will cause damage to your vehicle. Please contact the manufacturer if you are unaware of the system type in your vehicle.

Quick Installation:

The backup camera system is compatible with a wide range of vehicles and video display monitors.

This kit includes necessary wiring and cable connector accessories sufficient for typical connections. However, additional accessory cables and installation materials may be necessary for a completely secure and operational backup camera performance.

Connect the camera, using the red cable, of the DC 12V power cable, to the positive 12V reverse tail light in the rear of your car. You may need to temporarily remove an interior panel or other cover. Then, connect the black wire, of the DC 12V power cable, and ground properly. This connected power and ground cable connects to the camera, and will supply power to the camera directly. (Red wire is positive, black wire is negative)

Then use the included yellow RCA video connector cable, and run that cable to the yellow RCA video connector jack of the camera, to the RCA video connector of a compatible video display monitor.

*The system includes an additional video input connection, so you will have the ability to connect an additional video input source. The input source is then selectable via button on the mirror monitor assembly.

Connect the monitor using the included power and video wiring harness. Using the red cable, of the power and video wiring harness, connect to your vehicle's fuse panel (preferably to the 12V ignition switch) - which will only be powered when your vehicle is on, or activated by key. Then connect the black wire, of the DC 12V input, and ground properly. The colored wire, on the power and video wiring harness, is the 12V reverse gear positive trigger, which will provide a picture, to the mirror video monitor assembly, when the gear is placed in reverse. The power and video wiring harness then connects to the mirror video monitor assembly. This connection will supply power to the monitor directly.

- After installation test the camera before use. Placing your vehicle in reverse should provide a picture in the monitor within the rearview mirror assembly.

Mount the camera in the desired location, then connect the included RCA video cable, from the camera, and run the cable through to your video display's RCA connection. Make sure to route all cables and wiring in the least obtrusive route possible as to avoid conflict with other vehicle circuitry and to ensure a safe and stable installation/connection.

Controls

1Remote Window

2Analog Increase

3Menu

4Analog Decrease

5Input Selection

6ON/OFF

Interface Display

The rearview backup mirror monitor assembly provides soft touch button controls. Gain access to menu and power options by touching the desired buttons. Access the 'Menu' and make adjustments to Brightness, color, contrast and volume. ON/OFF switch controls power to the LCD display screen monitor. The 'Input Selection' button allows you to switch the LCD display source from connected inputs V1 / V2 (if an optional and compatible input source is connected).

Specifications

Camera:

Exterior License Plate Mount Cam

Marine Grade Waterproof Construction

IP 67 Water and Fog Resistance Rating

Night Vision Performance

Low Light 0.2 Lux Illumination

Extra Wide Viewing Angle

Slim Style Compact Camera

Mirror Monitor:

Built-into Rearview Mirror Assembly

Universal Size Clips onto Existing Mirrors

7" TFT / LCD Mirror Monitor Screen Display

16:9 Wide Screen

Resolution: 656 x 492 Pixels (RGB)

Anti Glare Coating

Dual Video Inputs

Ability to Connect Additional Video Source

Power Consumption: 6W

Auto Switch PAL/NTSC

Note:

Never connect the car monitor to cigarette lighters in vehicles with 24V DC power

Do not expose the monitor to high humidity levels, dust, steam, smoke or excessive direct sunlight.

Turn the power OFF when not in use.

Please refer to service from a qualified and professional service engineer when needed.

Dimensions / Size:

Screen (W x H): 5.9" x 3.25"

Mirror Assembly (L x W x H): 10.0" x 1.5" x 4.25"

Camera Dimensions (L x W x H): 8.46" W x 1.29"H x 1.37"D

graph TD
    A["Mirror Monitor Assembly"] --> B["Power Connection"]
    B --> C["Power & Wiring Harness"]
    C --> D["...to vehicle's 12V Ignition Switch"]
    D --> E["DC 12V Power Cable ...to vehicle's Reverse Lights"]
    E --> F["Camera"]
    C --> G["RCA Video Cable to Camera"]
    G --> H["Optional Video Input Connection"]
    G --> I["Ground"]
    G --> J["12V Reverse Gear Positive Trigger"]