LV803 - Video camera LG - Free user manual and instructions

Product Type	Color Video Camera
Model	LV803
Signal System	PAL / NTSC (depending on version)
Pick-up Device	6 mm Interline Color CCD
Total Pixels	470,000 (PAL) / 410,000 (NTSC)
Effective Pixels	440,000 (PAL) / 380,000 (NTSC)
Lens	Vari-Focal Lens (f = 2.8 mm to 11 mm / F = 1.2)
Horizontal Resolution	560 TV lines
Minimum Illumination	0.0002 lx (Sens-Up, F1.2)
S/N Ratio	More than 52 dB (AGC Off, F1.2)
Video Output	1.0 Vp-p Composite Signal (75 Ω)
Power Supply	AC 24 V (±20%) or DC 12 V (±10%), automatic switch
Power Consumption	Max 3.5 W
Operating Temperature	-10 °C to 50 °C (Humidity: 0% to 80% RH)
Storage Temperature	-20 °C to 60 °C (Humidity: 0% to 85% RH)
Weight	350 g
Dimensions (∅ x H)	∅ 140 x 100 mm
Day & Night Function	IR Cut Filter, Auto/Manual switching
WDR / BLC	60 dB WDR, BLC, HSBLC
Synchronization	Internal / Line Lock (AC only)
Dome Cover	Vandal-proof
OSD Menu	Multiple languages (English, Russian, etc.)

Frequently Asked Questions - LV803 LG

What power supply does the LG LV803 camera require?

The camera can be powered by AC 24 V (±20%) or DC 12 V (±10%) and automatically switches between them.

How do I adjust the focus and zoom on the LV803 camera?

Loosen the focus and zoom lock levers, adjust the lens by moving the levers, then tighten the levers to lock the settings.

What is the minimum illumination required for the camera to operate?

The camera can capture images in very low light, down to 0.0002 lx with Sens-Up enabled and F1.2 aperture.

Can the LV803 be used outdoors?

The operating temperature range is -10 °C to 50 °C with humidity up to 80% RH, but the camera is designed for indoor use only.

How do I access the OSD menu?

Press the SET button on the camera to display the main menu. Use UP/DOWN/LEFT/RIGHT buttons to navigate and adjust settings.

What is the purpose of the Day/Night function?

The Day/Night function automatically switches between color mode during daytime and black-and-white mode at night using an IR cut filter for better low-light performance.

How can I clean the camera lens?

Remove dust with a blower and clean the body with a dry soft cloth. For heavy dirt, use a cloth slightly dampened with neutral detergent and wipe dry. Avoid volatile solvents.

What is the resolution of the LG LV803 camera?

The camera provides 560 TV lines of horizontal resolution.

How do I reset the camera to factory settings?

Go to the RESET menu and select FACTORY RESET to restore all settings to default.

Can I connect a monitor directly to the camera for installation?

Yes, use the Video Out connector on the camera to connect a portable monitor for adjusting pan, tilt, zoom, and focus during installation.

USER MANUAL LV803 LG

Please read this manual carefully before operating your set and retain it for future reference.

MODEL

LV803

P/NO : MFL62723768

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Suitable conduit entries, knock-outs, or glands shall be provided in the cable entries of this product by the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V.

Veluwezoom 15, 1327

AE Almere, The Netherlands

(Tel: [phone])

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

1. Only use attachments/accessories specified by the manufacturer.
2. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

1. Unplug this apparatus during lightning storms or when unused for long periods of time.
2. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Cautions for Safe Operation

Power Supply

This camera must always be operated with a Certified/Listed, class 2 power supply only, AC 24 V or DC 12 V.

Note:

Be careful of AC frequency when the camera is operated with Line lock mode.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to cause fire or electric shock.

• Remove dust or dirt on the surface of the lens with a blower.
• Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent then wipe dry.
• Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. They may damage the surface finish and/or impair the operation of the camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

• Extremely hot or cold places (operating temperature -10 °C to 50 °C, however, we recommend that the unit be used within a temperature range of 0 °C to 45 °C) • Damp or dusty places
• Places exposed to rain • Places subject to strong vibration
• Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

Contents

Features 8

Part Names and Functions ...... 9

Connections 11

Basic connection ....11

Installation 12

Mounting the Camera without bracket 12

Mounting the Camera with bracket....14

Image Adjustment 16

Menu Operation....19

OSD Menu Overview ......20

General Operation 22

Camera Identification Settings 22

Exposure Settings 23

WDR/BLC setting 23

Brightness setting 24

AGC (Automatic Gain Control) setting .....25

SHUTTER (Shutter Speed) setting 25

SENS-UP setting 26

White Balance settings 26

Day/Night Setting 27

Motion Detection Setting 28

3D-DNR Setting 29

Privacy Setting 30

Special Menu Settings ....31

Setting the D-ZOOM (Digital Zoom) level .....31

Setting the D-EFFECT (Digital effect) ....32

Setting the SHARPNESS effect 32

Stabilizer setting 33

Setting the COLOR effect 33

Setting the SYNC (Synchronization) ....34

Setting the USER TITLE 34

Language Setting 35

Reset Settings 36

Specification 37

Features

This Color Video Camera is designed for installation in an indoor video surveillance system.

This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system.

Should you require any technical assistance, please contact authorized service center.

• High resolution and high sensitivity with a 6 mm CCD • 2.8 mm to 11 mm Vari-Focal Lens • Day & Night function (IR Cut Filter) • 560 TV lines of horizontal resolution • High sensitivity with a minimum scene illumination of 0.0002 lx (Sens-Up, F1.2) • BLC covers various light conditions • Excellent signal-to-noise ratio of 52 dB • Internal / Line Lock (External) • Power Supply: Automatically switch between DC 12 V and AC 24 V • Line Lock when using AC 24 V.

Dome Cover : Vandal-Proof

Part Names and Functions

1 Dome Cover 2 Lens Cover 3 Video output connector (BNC type) 4 Power input connector Supplies AC 24 V or DC 12 V from an external power source. 5 Focus lock lever Fixes the focus position after adjusting. 6 Setup menu control buttons 7 Video Out connector Use this jack for checking the picture with portable monitor when install the camera.

Part Names and Functions

8 Azimuth adjuster Adjusts the azimuth angle to obtain a level image. 9 Azimuth lock screw Fixes the azimuth angle after adjusting. 10 Zoom lock lever Fixes the zoom position after adjusting. 11 Pan lock screw Fixes the panning position after adjusting. 12 Camera mounting bracket This bracket is supplied for ceiling installation.

Connections

Basic connection

The peripheral devices (VCR, monitor, lens, etc.), AC adapter and cables are not supplied.

1. Connecting the monitor

Make the video signal connection between the camera and the monitor or DVR.

1. Supply AC 24 V or DC 12 V from an external power source.

Installation

Mounting the Camera without bracket

This camera can be installed directly on the surface of the wall or ceiling without bracket.

1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest.

1. Fasten the camera body to the ceiling.

Installation

1. Assemble the camera cover and camera body. For proper orientation, use the align mark to assemble the camera.

Installation

Mounting the Camera with bracket

This camera can be installed on the surface of the wall or ceiling using the supplied bracket.

1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest.

1. Fasten the camera bracket to the ceiling.

Installation

1. Fasten the camera body to the camera bracket. Tighten the screw to fix the camera body on the bracket.

1. Assemble the camera cover and camera body. For proper orientation, use the align mark to assemble the camera.

Installation

Image Adjustment

You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor.

Notes:

• Do not hold the camera by lens unit to adjust panning, tilting, or azimuth.
• The video output to the BNC will be interrupted while a portable monitor is connected to the video jack.
• Remove the Dome cover.
• Remove the lens cover.
• Connect a portable monitor to the video jack.

Installation

1. Adjust the pan/tilt position of the camera.

4-1. Lock the pan lock screw.

1. Adjust the azimuth angle.

5-1. Lock the azimuth angle screw.

1. Adjust the zoom

6-1. Unlock the zoom lever. 6-2. Move the lever to adjust the zoom.

Installation

6-3. Lock the lever.

1. Adjust the focus

7-1. Unlock the focus lever. 7-2. Move the lever to adjust the focus.

1. Attach the lens cover.
2. Attach the dome cover.

Menu Operation

This camera utilizes an on-screen user MENU. To set items on the menu, use the following buttons.

- UP button:

Moves the cursor upwards. Use this button to select an item or adjust the parameters.

• DOWN button:

Moves the cursor downwards. Use this button to select an item or adjust the parameters.

• RIGHT button:

Moves the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed.

• LEFT button:

Moves the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed.

- SET button:

Executes selections and displays a submenu for an item with the ▼mark.

Menu Operation

OSD Menu Overview

The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus.

Main Menu Sub Menu Contents
CAMERA ID - OFF, 1 to 255
EXPOSURE ALC/ ELC		WDR/BLC	OFF/WDR/BLC/HSBLC
		BRIGHTNESS 0 to 100
		AGC	OFF/LOW/MIDDLE/HIGH
		SHUTTER	X512, ..., x2, AUTO,OFF, A.FLK, 1/160,..., 1/90 000
		SENS-UP	OFF
			AUTO
		EXIT RET/TOP/END

Main Menu Sub Menu Contents
WHITE BAL	ATW
	AWC ➔ PUSH
	MANUAL	COLOR TEMP	INDOOR, OUTDOOR
		RED -100 to 100
		BLUE -100 to 100
		EXIT RET/TOP/END
DAY/NIGHT	AUTO	LEVEL	LOW/ MIDDLE/ HIGH
		DWELL TIME	5, 10, 15, 30, 60 SEC.
		EXIT RET/TOP/END
	DAY
	NIGHT
MOTION DET	ON	ZONE NUMBER A	REA1 to 4
		ZONE STATE	ON/OFF
		HEIGHT 12 to	100
		WIDTH 16 to	100
		MOVE Y	6 to 94
		MOVE X	8 to 92
		SENSITIVITY	0 to 100
		EXIT RET/TOP/END
	OFF

Menu Operation

Main Menu Sub Menu Contents
3D-DNR	OFF -
	LOW -
	MIDDLE -
	HIGH -
PRIVACY	OFF -
	ON	MASK NUMBER A	REA1 to AREA8
		DISPLAY ON/OFF
		COLOR	GRAY, WHITE, BLACK
		HEIGHT 4 to 100
		WIDTH 4 to 100
		MOVE Y 2 to 98
		MOVE X 2 to 98
		EXIT RET/TOP/END

Main Menu Sub Menu Contents
SPECIAL	D-ZOOM	OFF
		ON	ZOOM
			PAN
			TILT
			EXIT
	D-EFFECT	OFF/V-FLIP/MIRROR/ROTATE
	SHARPNESS	0 to 68
	STABILIZER	OFF/ON
	COLOR	OFF/ON
	SYNC INT / LL
	USER TITLE	OFF/ON
	LANGUAGE	ENG/RUS (The supported language can be different depending on the model.)
	EXIT	RET/TOP/END
RESET	CAMERA REBOOT	-
	FACTORY RESET	-
	EXIT	RET/TOP/END
EXIT	-	-

Menu Operation

General Operation

1. Press [SET] button.

The setup menu screen appears on the monitor.

1. Use [UP] or [DOWN] button to select an option then press [SET] button. Submenu appears on the monitor.
2. Use [UP] or [DOWN] button to select a submenu option.
3. Use [LEFT] or [RIGHT] button to select a value.
4. Select [EXIT] option then press [SET] to exit the setup menu. In the submenu, use [UP] or [DOWN] button to select the [EXIT] then use [LEFT] or [RIGHT] button to select a mode and press [SET] to exit the setup menu.

RET: Return to the previous.

• TOP: Return to the CAMERA SETTING menu screen. • END: Exit the setup menu.

Camera Identification Settings

You can use the camera identification (CAMERA ID) to assign a number to the camera.

1. Select [CAMERA ID] option on the [CAMERA SETTING] menu.
2. Use [LEFT] or [RIGHT] to select a CAMERA ID (OFF, 1 to 255).

Menu Operation

Exposure Settings

You can set the exposure options using the EXPOSURE menu.

Select [EXPOSURE] option on the [CAMERA SETTING] menu.

Press [SET] button and the EXPOSURE menu appears.

WDR/BLC setting

Use WDR/BLC option to view the object clearly in backlight conditions.

1. Select [WDR/BLC] option.
2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].

- WDR: Use for adjusting brightness of the subject and background image to view the both of object clearly at the same time in backlight condition. Set the WDR limit.

WDR LIMIT: LOW ↔ MIDDLE ↔ HIGH

• BLC: Use for adjusting brightness of the subject to view the object clearly in backlight condition. Set the BLC limit.

BLC LIMIT: LOW ↔ MIDDLE ↔ HIGH

Menu Operation

• HSBLC: Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low illuminance scene.

AREA SETTING: Use [LEFT] or [RIGHT] button to select an area then use [UP] or [DOWN] button to select ON or OFF. Press [SET] to exit the Area setting menu. GRAY SCALE: Use [LEFT] or [RIGHT] button to select a gray scale. (GRAY←→D.GRAY←→BLACK). USER SCALE: Use [LEFT] or [RIGHT] button to select a bright level. (5 levels) MASK: Use [LEFT] or [RIGHT] button to select [ON] or [OFF]. If you set the MASK to ON, the mask function is activated only when the HSBLC is automatically activated in low luminance scene.

• OFF: Not used.

Brightness setting

You can set the brightness level. (0 to 100)

1. Select [BRIGHTNESS] option.
2. Use [LEFT] or [RIGHT] button to set the bright level.

Menu Operation

AGC (Automatic Gain Control) setting

If the images are too dark, change the maximum [AGC] value to make the images lighter.

1. Select [AGC] option.
2. Use [LEFT] or [RIGHT] button to select a mode. (OFF←→ LOW←→MIDDLE←→HIGH)

SHUTTER (Shutter Speed) setting

1. Select [SHUTTER] option.
2. Use [LEFT] or [RIGHT] button to set shutter speed. (AUTO ↔ OFF ↔ A.FLK ↔ 1/160, ..., 1/90 000 ↔ x512, ..., x2)

Menu Operation

SENS-UP setting

If pictures are not clear due to darkness, use to increase the sensitivity of the picture.

1. Use [UP] or [DOWN] button to select [SENS-UP] option.
2. Use [LEFT] or [RIGHT] button to select mode.

• AUTO: Adjust the sensitivity of the picture automatically.

SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set the SENS-UP limit.

EXIT: Select a mode and press [SET] to exit the menu.

• OFF: Not used.

Note:

If you set to one of the SHUTTER options except AUTO on the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed.

White Balance settings

You can select one of three modes for white balance adjustment.

1. Select [WHITE BAL] option.
2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].

Menu Operation

- ATW (Auto-Tracing White Balance): The color temperature range for the proper white balance is approximately 1,700 K to 11,000 K. Proper white balance may not be obtained under the following conditions:

The color temperature is out of the 1,700 K to 11,000 K range. When the scene contains mostly high color temperature objects, such as a blue sky or sunset. When the scene is dim.

- AWC→PUSH: If you select the AWC→PUSH mode, you will be able to set up the White Balance automatically using [SET] button.

• MANUAL: You can set the white balance options manually.

COLOR TEMP: Use [LEFT] or [RIGHT] button to select a function.

- INDOOR: The color temperature range for the proper white balance is approximately 3,200 K.

- OUTDOOR: The color temperature range for the proper white balance is approximately 5,100 K.

RED: Obtains the optimum amount of red gain. BLUE: Obtains the optimum amount of blue gain.

Day/Night Setting

1. Select the [DAY/NIGHT] option.
2. Use the [LEFT] or [RIGHT] button to select the mode for the day/night function.

Menu Operation

• AUTO: You will be able to change the Day/Night mode automatically.

Note:

If you set the AGC to [OFF] or the SHUTTER is set to one of the SHUTTER options except AUTO on the [EXPOSURE] menu, the AUTO mode of the DAY/NIGHT function is not available and the [---] mark is displayed.

LEVEL: Use the [LEFT] or [RIGHT] button to select a level. (LOW←→MIDDLE←→HIGH)

DWELL TIME: Use the [LEFT] or [RIGHT] button to select a dwell time. (5, 10, 15, 30 or 60 SEC.)

• DAY: Color mode enabled. • NIGHT: Black-and-white mode enabled.

Motion Detection Setting

The motion detection detects moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection in 4 zones.

1. Select the [MOTION DET] option.
2. Use the [LEFT] or [RIGHT] button to select [ON] and press [SET]. The MOTION DETECTION menu appears.
3. Use the [LEFT] or [RIGHT] button to select a zone number (AREA1 to AREA4) on the [ZONE NUMBER].
4. Use [LEFT] or [RIGHT] button to set the ZONE STATE to ON or OFF.

Menu Operation

1. Use [UP] or [DOWN] to select an option, then use [LEFT] or [RIGHT] button to adjust the option.
2. HEIGHT: Enlarge or decrease the vertical size of the mask.
3. WIDTH: Enlarge or decrease the horizontal size of the mask. • MOVE Y: Moves vertical position of the mask. • MOVE X: Moves horizontal position of the mask.
4. Use the [SENSITIVITY] option to obtain the optimum detection level.

3D-DNR Setting

1. Select the [3D-DNR] option. If pictures are not clear due to brightness, use this to reduce the noise of the picture.
2. Use the [LEFT] or [RIGHT] button to select an option. (OFF←→LOW←→MIDDLE←→HIGH)

Notes:

• If you set the AGC to [OFF] on the [EXPOSURE] menu, the [3D-DNR] function is not available and the [---] mark is displayed. • When you use this function, afterimages may occur.

Menu Operation

Privacy Setting

This function is aimed at protecting personal privacy by selecting a screen part to be blacked out and not displayed on the screen. Up to 8 zones can be registered.

1. Select the [PRIVACY] option.
2. Use the [LEFT] or [RIGHT] button to select [ON] and press [SET]. The PRIVACY SETUP menu appears.
3. Use the [LEFT] or [RIGHT] button to select a mask (AREA1 to AREA8) on the [MASK NUMBER].
4. Use the [LEFT] or [RIGHT] button to set the ON or OFF on the DISPLAY option.
5. Use the [LEFT] or [RIGHT] button to set the GRAY,

WHITE, or BLACK on the COLOR option.

1. Use [UP] or [DOWN] to select an option, then use [LEFT] or [RIGHT] button to adjust the option.

• HEIGHT: Enlarge or decrease the vertical size of the mask. • WIDTH: Enlarge or decrease the horizontal size of the mask. • MOVE Y: Moves the vertical position of the mask. • MOVE X: Moves the horizontal position of the mask.

Menu Operation

Special Menu Settings

This menu lets you adjust and set up D-ZOOM, D-EFFECT, SHARPNESS, COLOR, SYNC, USER TITLE, and LANGUAGE functions by yourself in the SPECIAL menu.

1. Select the [SPECIAL] option.
2. Press [SET] button and the SPECIAL menu appears.

Setting the D-ZOOM (Digital Zoom) level

You can select the digital zoom level.

1. Select [D-ZOOM] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select [ON] then press [SET]. The DIGITAL ZOOM menu appears. When you set to ON, the displayed image can be shaking.
3. Use [UP] or [DOWN] to select an option, then use [LEFT] or [RIGHT] button to select a level.

• ZOOM: Use [LEFT] or [RIGHT] button to enlarge the screen. • PAN: Use [LEFT] or [RIGHT] button to move the screen (left or right). • TILT: Use [LEFT] or [RIGHT] button to move the screen (up or down).

Menu Operation

Setting the D-EFFECT (Digital effect)

You can select the digital effect.

1. Select [D-EFFECT] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select a digital effect.

• V-FLIP: Flip the picture vertically. • MIRROR: Turn on the mirror effect. • ROTATE: Rotate the picture (180°). • OFF: Turn off the digital effect.

Setting the SHARPNESS effect

You can select the sharpness effect.

1. Select [SHARPNESS] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to change and adjust the option.

Menu Operation

Stabilizer setting

The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration.

This function is useful for outdoor surveillance.

Select [STABILIZER] option and set to ON or OFF.

Note:

If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1] automatically.

Setting the COLOR effect

You can select the color effect.

1. Select [COLOR] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to change a color effect.

• ON: To display the picture with color. • OFF: To display the picture with grayscale.

Menu Operation

Setting the SYNC (Synchronization)

The SYNC function is available only with AC power source.

1. Select [SYNC] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select [INT] or [LL] (Line Lock).

• INT: Selects for using the internal synchronization.

- LL (Line Lock): Selects for the operation of multi cameras because it synchronizes the camera phase by using the external signal (AC power signal).

2-1. Select [LL] mode and press [SET]. 2-2. Select a desired phase using the [LEFT] or [RIGHT] button.

Note:

When you use the DC 12 V power, the [SYNC] option is fixed to [INT] mode only.

Setting the USER TITLE

You can use the camera identification to assign a number and character to the camera (0 to 9, A to Z, a to z). The USER TITLE is displayed on the upper left of the screen. To disappear the user title, select [OFF].

1. Select [USER TITLE] option on the [SPECIAL] screen.
2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET]. The USER TITLE menu appears.

Menu Operation

1. Use [UP], [DOWN], [LEFT] or [RIGHT] button to select a character or number.

• CLR: If you enter the wrong code, select CLR then press [SET]. • POS: Use [UP], [DOWN], [LEFT] or [RIGHT] button to move position of USER TITLE on the screen. • END: Confirm your selection. • 1 (Blank): Inserts a space at the cursor position. • / Moves cursor to left or right.

Language Setting

Select a language for the Setup menu and on-screen display.

1. Select [LANGUAGE] option on the [SPECIAL] screen.
2. Press [LEFT] or [RIGHT] button to select a language.

Menu Operation

Reset Settings

1. Select [RESET] option.
2. Press [SET] button and the RESET menu appears.
3. Use [UP] or [DOWN] to select option.

• CAMERA REBOOT: To reboot the camera system. • FACTORY RESET: To reset the camera setting to factory setting, select [FACTORY RESET] option.

Specification

Item LV803P LV803N
Signal System PAL NTSC
Total/Effective Pixels 470 000 Pixels / 440 000 Pixels 410 000 Pixels / 380 000 Pixels
Pick-up Device 6 mm Interline Color CCD
Lens Vari-Focal Lens (f = 2.8 mm to 11 mm / F = 1.2)
Iris DC/ELC Selectable
Signal Process LG XDI-s
Scanning System 2:1 Interlace
Synchronization System Internal/Line Lock
Scanning Frequency 50 Hz(VD)	59.94 Hz(VD)
Resolution	560 Lines
S/N Ratio	More than 52 dB (AGC Off, F 1.2)
Low Luminance	0.0002 lx (Sens-up Auto)0.7 lx (AGC High, DNR)
Video Output Signal	1.0 Vp-p Composite Signal (75 Ω)
Auto Gain Control	OFF/LOW/MIDDLE/HIGH

Specification

Item LV803P LV803N
Exposure ALC/ELC
Electric Shutter 1/50 to 1/90 000 (Auto Mode) 1/60 to 1/90 000 (Auto Mode)
White Balance ATW / AWC->PUSH / MANUAL
Back Light OFF/WDR/BLC/HSBLC
WDR 60 dB
MOTION DET. OFF/ON
Power Consumption Max 3.5 W
Power Source AC 24 V (±20 %), DC 12 V (±10 %)
Operation Temperature -10 °C to 50 °C (Humidity: 0 % RH to 80 % RH)
Storage Temperature -20 °C to 60 °C (Humidity: 0 % RH to 85 % RH)
Weight	350 g
Dimension (∅ x H)	∅ 140 x 100 mm

LG

Life's Good

AB28