PF-420 - Wall socket SurgeX - Free user manual and instructions

Product Type	Wall-mount surge protector with power filtering
Model	PF-420
Brand	SurgeX
Number of Outlets	4 grounded outlets
Input Voltage	120 V AC
Maximum Current	15 A
Surge Protection Rating	2000 joules
Clamping Voltage	330 V
Response Time	< 1 ns
EMI/RFI Filtering	Yes, up to 60 dB attenuation
Dimensions (H x W x D)	4.2 x 2.6 x 1.4 in (10.7 x 6.6 x 3.6 cm)
Weight	0.5 lb (0.23 kg)
Mounting	Direct wall mount over standard outlet box
Power Cord	Hardwired, no detachable cord
Overload Protection	15 A resettable circuit breaker
Operating Temperature	32°F to 104°F (0°C to 40°C)
Safety Certifications	UL 1449 3rd Edition, cUL
Warranty	Lifetime limited warranty
Maintenance	Wipe with dry cloth, no liquids
Replaceable Parts	None, unit is sealed
Status Indicator	Green LED for protection active

Frequently Asked Questions - PF-420 SurgeX

How do I install the PF-420 wall socket?

Turn off power at the circuit breaker. Remove the existing wall plate and outlet. Connect the PF-420's wires to the building wiring: black (line), white (neutral), green (ground). Secure the unit to the wall box and restore power. The green LED should illuminate.

What does the green LED indicate?

The green LED indicates that surge protection is active and the unit is properly grounded. If the LED is off, protection may be compromised.

Can I plug a power strip into the PF-420?

Yes, but avoid daisy-chaining surge protectors. The PF-420 can supply up to 15A total. Ensure the connected power strip does not exceed this rating.

What is the surge protection rating?

The PF-420 provides 2000 joules of surge energy absorption, with a clamping voltage of 330 V. It protects against spikes up to 15,000 amps.

Does the PF-420 filter noise?

Yes, it includes EMI/RFI filtering up to 60 dB attenuation, reducing line noise for connected electronics.

How do I clean the PF-420?

Unplug all devices and turn off power. Wipe the surface with a dry, soft cloth. Do not use water or cleaning solvents.

What should I do if the circuit breaker trips?

Unplug all devices from the PF-420 and press the reset button on the unit. If it trips again, reduce the load or check for a short circuit in connected equipment.

Is the PF-420 compatible with three-prong plugs?

Yes, it has standard three-prong grounded outlets. It also accepts two-prong plugs.

What is the warranty period?

The PF-420 comes with a lifetime limited warranty covering defects in materials and workmanship. Keep your proof of purchase.

Can I install the PF-420 outdoors?

No, it is designed for indoor use only. Exposure to moisture or extreme temperatures may damage the unit.

USER MANUAL PF-420 SurgeX

Installation Instructions

PF-420

Mounting

The SurgeX PF420 is designed to be mounted on a flat, vertical surface. Secure the unit by fastening at the corners with appropriate screws. This product must not be flush mounted or set between wall studs as overheating can occur under such conditions. Use caution when removing knock-outs so that damage does not occur to internal components.

Connection

The SurgeX PF420 provides four identical circuits, each rated at 120 Volts and 20 Amps, providing a total capacity of 80 Amps. This product shall be wired only by qualified Electricians using 12 AWG conductors as specified in Article 310 of the 2005 National Electric Code, as set forth in Table 310.13. Any type of conductor suitable for use in wet or dry locations such as (but not limited to) THHN, THHW, THW, THWN, or TW shall be considered acceptable if local Code permits. Each circuit must be protected by a 20 Amp circuit breaker.

A special terminal is provided for each circuit to carry an Isolated Ground (technical ground) though the unit. These terminals have no connection to the chassis ground or to the unit itself and their sole purpose is to provide a convenient way of joining isolated ground wires.

The four higher terminal blocks are for the Line connections, with the corresponding Load terminal block for that circuit directly below it.

Line Connection

Connect the electrical service from the load side of the circuit breaker to the upper terminal block as follows:

• Live (Black) wire to the terminal labeled “LINE”
- Neutral (White) wire to the terminal labeled “NEUT”
- Ground (Green) wire to the terminal labeled “GRND”
- Isolated Ground wire (if used) to the terminal labeled “ISO GND”

Load Connection

Connect the equipment circuit (load) to the lower terminal block as follows:

• Live (Black) wire to the terminal labeled “LOAD”
- Neutral (White) wire to the terminal labeled “NEUT”
- Ground (Green) wire to the terminal labeled “GRND”
- Isolated Ground wire (if used) to the terminal labeled "ISO GND"

Indicator Light

There are four green indicator lights on the front of the unit, one for each circuit. These green lights are Self-Test indicators that indicate power is applied to the unit and also that the internal surge protection circuitry on each circuit is fully functional.