CPD-8C - Uncategorized Citronic - Free user manual and instructions

Product Type	19" 8-Way IEC Power Conditioner
Rack Mount Size	19" 1U
Dimensions	482 x 178 x 44 mm
Weight	2.6 kg
Power Supply	230 Vac, 50 Hz
Max Output Current	10 A
Outputs	8 x IEC power outlets (rear)
LED Type	2 x 3W LED lamps (front)
Filtering	RFI/EMI filter
Surge Protection	Yes, surge and voltage spike protection
Circuit Breaker	10 A, press to reset
Front Panel Controls	On/Off power switch, dimmer switch for lamps, circuit breaker, LED lamps (pull out)
Rear Panel	Power inlet, 8 x IEC outputs
Safety Warning	Do not open cover; contains high voltage. No user-serviceable parts.
Disposal	WEEE – do not dispose with household waste; follow local council guidelines.
Warranty	Damage due to misuse voids warranty

Frequently Asked Questions - CPD-8C Citronic

What is a power conditioner?

A power conditioner is a device that filters electrical noise and surges from the mains supply, protecting sensitive audio, video, or computer equipment. The Citronic CPD-8C includes an RFI/EMI filter and surge protection.

How do I mount the CPD-8C in a rack?

The CPD-8C is designed for 19" rack mounting with a 1U height. Use four screws to secure it to the rack rails. Ensure proper ventilation and do not block the rear IEC outlets.

What does the RFI/EMI filter do?

The RFI/EMI filter reduces high-frequency interference from sources like fluorescent lights, dimmers, and other electronic devices, preventing noise from entering the AC line and affecting your connected equipment.

How to use the front LED lamps?

The front panel has two LED lamps that can be pulled out to illuminate the rack. Use the dimmer switch to adjust their brightness. The lamps are on/off controlled by a dedicated power switch.

What is the circuit breaker for?

The 10A circuit breaker protects against overcurrent. If tripped, press the button to reset after removing the cause of overload. It does not replace a main fuse.

Does the CPD-8C protect against power surges?

Yes, it includes surge and voltage spike protection to safeguard connected equipment. However, for extreme surges (e.g., lightning), additional surge protection may be needed.

What is the maximum load I can connect?

The maximum total output current is 10A at 230V, so do not exceed 2300W. Each IEC outlet can supply up to 10A, but the total load across all outlets must not exceed 10A.

How to clean and maintain the power conditioner?

Disconnect from mains before cleaning. Wipe the exterior with a dry cloth. Do not use liquids or sprays. Check for dust buildup on vents and remove with a soft brush. No internal maintenance is required.

Can I repair the CPD-8C myself?

No, the device contains high voltage and no user-serviceable parts. Refer to qualified personnel for service or repair. Opening the cover voids the warranty and poses a safety risk.

How should I dispose of the CPD-8C?

The CPD-8C is classified as WEEE (Waste Electrical and Electronic Equipment). Do not dispose of it with household waste. Follow your local council guidelines for recycling electronic equipment.

USER MANUAL CPD-8C Citronic

19" 8-WAY IEC POWER CONDITIONER

Item ref: 776.498UK

User Manual

Please do not open cover as it contains high voltage. This product is not serviceable or repairable by the end user.

Please refer to qualified personnel for service or repair.

Please read this manual thoroughly before use. Any damage caused by misuse of the product will void the warranty.

Protect your electronic equipment with this 19" rack mountable power conditioner featuring an RFI/EMI filter. The filter works by preventing noise from fluorescent lights, certain dimmers and similar sources of electronic pollution contaminating the AC line and leaking into sensitive audio, video or computer circuits. In addition; the front panel features two LED lamps with dimmer control for illuminating your rack.

• 19" 1U rack mountable
• 8 rear mounted IEC power outlets
• 2 front mounted LED lamps with dimmer control

• Surge and voltage spike protection
  • 10A capacity with circuit breaker

Specifications

Power supply 230Vac, 50Hz Max. output current 10A Outputs 8 x IECs LED type 2 x 3W LEDs Dimensions 482 x 178 x 44mm Weight 2.6kg

Front Panel

1. On/Off power switch for rack lamps
2. Dimmer switch for LED rack lamps
3. LED rack lamps, pull out to use
4. 10A circuit breaker, press to reset
5. On/Off power switch

Rear Panel

1. Power in
2. 8 x IEC power outputs

This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted. Copyright© 2016. AVSL Group Ltd.