AM-118 - Mounting accessories Vivotek - Free user manual and instructions

Product Type	Pendant Head Mounting Accessory for Speed Dome Cameras
Brand	Vivotek
Model	AM-118
Compatible Cameras	Vivotek Speed Dome SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, SD8362E
Material	Metal (aluminum/steel) with corrosion-resistant coating
Dimensions (Approx.)	Diameter 120 mm, Height 80 mm (pendant head only)
Weight (Approx.)	0.6 kg
Mounting Type	Ceiling pendant mount (with or without pendant pipe)
Included Accessories	Alignment sticker, M6.2x75mm screws (4), M5x8 screws (3), 3mm hex wrench
Color	White
Installation Method	Drill holes, insert anchors, secure with screws, attach pendant adapter (AM-519)
Usage Environment	Indoor and outdoor (with proper sealing)
Operating Temperature	-40°C to 50°C (typical for Vivotek accessories)
Ingress Protection	IP66 (when properly installed with cables sealed)
Load Capacity	Up to 5 kg (estimated for speed dome)
Safety Features	Anti-tamper screws, secure locking design
Maintenance	Clean with soft dry cloth; avoid water or solvents
Compliance	RoHS, CE (assumed)

Frequently Asked Questions - AM-118 Vivotek

What is the Vivotek AM-118 pendant head used for?

The Vivotek AM-118 is a pendant head designed for mounting Vivotek speed dome cameras (e.g., SD83xx series) to a ceiling. It can be used alone or with an optional pendant pipe (AM-116 or AM-117) to extend the drop.

Is the AM-118 compatible with all Vivotek speed dome cameras?

The AM-118 is specifically compatible with Vivotek speed dome models: SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, and SD8362E. Other models may require a different adapter.

What tools are needed to install the AM-118?

You will need a drill with a 10mm bit, hammer, screwdriver (Phillips), and the included 3mm hex wrench. For the pendant pipe versions, additional wrenches may be required.

How do I route cables through the AM-118?

Before mounting, route the Ethernet and power cables through the waterproof connector and rubber seal plug, then through the pendant head. A 1-inch conduit can be used for cable management.

Can the AM-118 be used outdoors?

Yes, when properly installed with the provided seals and waterproof connectors, the AM-118 is suitable for outdoor use. Ensure all cable entries are sealed to maintain IP66 protection.

What is the weight capacity of the AM-118?

The AM-118 is designed to support the weight of Vivotek speed dome cameras, typically up to 5 kg. For heavier loads, reinforce the ceiling mounting.

Do I need to use an alignment sticker for installation?

Yes, the included alignment sticker helps mark the correct drilling positions on the ceiling. Use it to ensure precise hole placement for the mounting screws.

Can the AM-118 be installed without a pendant pipe?

Absolutely. The AM-118 can be mounted directly to the ceiling using the pendant head alone. Follow the 'Pendant Mount without Pendant Pipe' instructions for direct mounting.

What should I do if the screws feel obstructed when inserting through the pipe?

If resistance is felt, gently twist the bolt to avoid damaging cables inside the pipe. This is important for parapet mounts where cables run through the pipe arm.

How do I clean and maintain the AM-118?

Clean the pendant head with a soft, dry cloth. Avoid water, solvents, or abrasive cleaners. Periodically check that all screws remain tight and the mount is secure.

USER MANUAL AM-118 Vivotek

VIVOTEK SD83XXE Speed Dome Mounting Accessories

AM-116/117 Pendant Pipe

AM-118 Pendant Head

AM-221 Gooseneck

AM-231 Parapet Mount

AM-519 Pendant Adaptor

Installation Guide

Corresponding part numbers:

AM-116: 900014300G

AM-117: 900014400G

AM-118: 900014600G

AM-221: 900014800G

AM-231: 900015000G

AM-519: 900014900G

Rev. 1.1

Revision History:

Rev. 1.0: Initial release
Rev. 1.1: Adding corresponding ordering part numbers and supported speed dome models.

Compatible VIVOTEK Cameras

Speed Dome SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, SD8362E

Mechanical Drawings

AM-118 Pendant Head

AM-116 20cm Pendant Pipe
AM-117 40cm Pendant Pipe

1 1/2" PS11

AM-519 Pendant Adapter (comes with the network camera)

AM-221 Gooseneck

AM-231 Parapet Mount

AM-231 Parapet Corner Mount

AM-231 Parapet Mount - Alignment Sticker

AM-231 Corner Mount - Alignment Sticker

Preparation before Installation

Connect Ethernet cable and IO wires (this may include the AC24V wires) to the interface section of the camera, and then combine the interface section with the dome cap. Note that you must route cables through the waterproof connector and the rubber seal plug, and install them to the dome cap. Please refer to the Quick Installation Guide for details.

Cabling should be done before mounting the camera.

IV-1. Pendant Pipe Mounting: AM-116/-117 & AM-118

Shown below are the dimensions of a pendant mount configuration using the 40cm pendant pipe.

IV-1-1. Pendant Mount without Pendant Pipe: AM-118

Below are the sample procedures using a pendant head and pendant pipe:

1. Determine a hard surface ceiling location, and use the alignment sticker to mark the positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.

Note that mounting holes should be 10mm in diameter and 60mm deep. The included screws are M6.2 x75mm.

Diagram of a ceiling-mounted air purifier with three identical height sensors and a central control unit (no text or symbols)

1. Install a pendant adapter (AM-519) by turning it clockwise to the pendant head, and secure the connection using an included 3mm hex wrench.

Mechanical assembly diagram showing a rotating component with directional arrows indicating motion (no text or labels)

AM-519

1. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit.
2. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.

1. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. When done, secure the connection using an included 3mm hex wrench.

1. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.

IV-1-2. Pendant Mount with Pendant Pipe: AM-116/AM-117 & AM-118

Below are the sample procedures using a pendant head and pendant pipe:

1. Determine a hard surface ceiling location, and use the alignment sticker to mark the positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.

Note that mounting holes should be 10mm in diameter and 60mm deep. The included screws are M6.2 x75mm.

Diagram of a spray gun system with three identical rocket components and a central platform, enclosed in a ceiling frame (no text or symbols)

1. Install a 20cm or 40cm pendant pipe (AM-116 or AM-117) by turning it clockwise to the pendant head, and secure the connection using an included 3mm hex wrench.

Mechanical assembly diagram showing a shaft with flange and rotating components, no text or symbols present

1. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit.
2. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.

1. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws.

Technical line drawing of a mechanical assembly with a screw and base mount (no text or symbols)

1. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.

IV-2. Gooseneck Mounting: AM-221

Below is a sample procedure using a gooseneck bracket:

1. Determine a hard surface wall location. Use the alignment sticker to mark the positions where holes will be drilled for the gooseneck bracket.
2. Drill 4 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer in threaded anchors. Note that you should hammer the anchors with hex nuts on them so that the threaded poles will not be deformed! If preferred, drill another hole for routing cables.

3. Secure the wall mount bracket to wall using 4 sets of lock washers and nuts.

4. Attach the top section (dome cap and interface section) of the camera to the gooseneck bracket

Install AM-519 adaptor to the gooseneck.

1. Align the camera body with the top section. Align the alignment mark on the camera with that on the interface section. Push the camera up to match the top section.

1. Rotate the camera clockwise until its alignment mark is aligned with the "C" mark.
2. Use the included T25 stardriver to tighten the 3 anti-tamper screws from the top. Make sure all parts have been securely tightened.

The dimensions of the gooseneck installation are shown below.

IV-3. Parapet Mounting: AM-231

The screws included in the parapet set are:
Sleeve anchors 5/16" x3" 6
Hex bolts M8x25 6
Hex bolts M8x70 3
Hex lock nuts M8 6
Washers M8 15
Lock washers M8 15

IMPORTANT:

The parapet wall should have a concrete strength of 4000 PSI or higher. Each sleeve anchor can withstand an 800kgs pull-out force.

The parapet bracket is designed for installation on the inside of a parapet. Note the following before you start to install:

1. There must be a clearance of 65mm between the upper edge of the parapet wall and the metal bracket fixed to the wall. You can flush align the upper edge of the alignment sticker with the edge of a parapet wall.
2. At least two inches of space should be available below the parapet bracket for routing cables.

The space requirements for a parapet mount are shown below:

Below is a sample procedure using the parapet mount bracket:

1. Determine a hard surface location. Use the alignment sticker to mark the positions where holes will be drilled for the bracket.
2. Drill 6 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer in the sleeve anchors. Note that you should hammer the anchors with hex nuts and washers on them so that the threaded poles will not be deformed!

Diagram showing a 3D block with dashed lines indicating direction and a separate tool emitting a cylindrical component (no text or symbols present)

1. Install the brackets to wall using the hex nuts and washers from the sleeve anchors.

NOTE:

If you install the corner parapet bracket, use the included alignment sticker, and mark the drill holes through the mounting slots on the brackets.

Technical line drawing of three bracket clamps mounted on a vertical support structure (no text or symbols)

1. Use a crescent wrench to secure the outer brackets to the brackets on the wall using the M8x25 hex bolts and washers. Do not completely tighten the bolts yet! When the speed dome is installed to the mount pipe, it needs to be swiveled out to the desired position.

Illustration of a mechanical assembly with a wrench, a spring, and bolts (no text or symbols)

1. Install the AM-519 adapter to the parapet pipe.

2. Feed cables through the pipe arm. The cable length for passing through the pipe arm is 250cm at least. You can pass a rigid copper wire through the pipe arm first, and use it to pull other wires through the pipe.

Diagram of a curved pipe system with fluid flow and directional arrows, no text or symbols present

1. Install the top section of the camera to the pipe arm by driving 3 M5 x8 screws.

Diagram showing a pipe fitting with a screwdriver and a base mount, no text or symbols present

1. Insert the pipe arm into the round openings on the brackets until it is rested on the bottom bracket.

Technical line drawing of a mechanical or electrical assembly with pipes and connectors, no text or symbols present

1. Install the camera to the top section. For installation details, refer to the Quick Installation Guide or page 15 in this document.

Technical line drawing of a mechanical or electrical assembly with pipes, connectors, and a spherical component (no text or symbols)

1. Swivel the pipe arm outwards to the opposite position. Use the M8 x70 bolts to secure the pipe arm to the brackets. You also need to tighten the M8 x25 bolts between the inner and outer brackets.

IMPORTANT:

When inserting the M8 bolts, you may damage the cables inside. Try twist the bolts a bit to get around cables if you feel resistance when inserting through the pipe.

A corner parapet installation should look like this when its installation is completed.

Technical line drawing of a mechanical device with a bulb and connecting rod, mounted on a rectangular base (no text or symbols)

This page is intentionally left blank.