ADR-D 230 D63 - Energy consumption meter Vemer - Free user manual and instructions

Product Type	Energy Consumption Meter
Brand	Vemer
Model	ADR-D 230 D63
Mounting	DIN Rail (4 modules)
Dimensions (W x H x D)	70 mm x 90 mm x 65 mm
Weight	Approx. 200 g
Rated Voltage	230 V AC, 50 Hz
Rated Current	63 A (max)
Measurement Type	Single-phase active energy (kWh)
Accuracy Class	Class B (per EN 50470)
Display	LCD, 6+1 digits
Pulse Output	Yes (S0, 1000 imp/kWh)
Operating Temperature	-25°C to +55°C
Storage Temperature	-35°C to +70°C
Humidity Range	Up to 95% non-condensing
Protection Class	IP20 (front), IP50 (terminal block)
Main Functions	Measures active energy, instantaneous power, total consumption, partial consumption
Maintenance	Dry cloth cleaning; no user-serviceable parts
Safety Standards	IEC 61010, IEC 62053-21
Spare Parts / Reparability	Contact Vemer for replacement; device is not user-repairable

Frequently Asked Questions - ADR-D 230 D63 Vemer

How do I install the Vemer ADR-D 230 D63 energy meter?

Install on a DIN rail in a suitable enclosure. Connect phase (L) and neutral (N) according to the wiring diagram provided. Ensure the main power is off. Use appropriate fuses and comply with local electrical codes.

What does the LCD display show?

The LCD shows total active energy consumption in kilowatt-hours (kWh) with 6 integral and 1 decimal digit. It may also show instantaneous power if configured.

What is the accuracy class of this meter?

The meter is Class B as per EN 50470, with an error less than ±1% under nominal conditions.

Can I use this meter with a solar PV system?

Yes, it can measure energy consumption in both directions (import/export) when installed appropriately with a bidirectional meter or external direction sensor.

How do I reset the partial consumption reading?

Press and hold the reset button (if available) for 3 seconds to zero the partial register. Refer to the manual for exact location.

What does the pulse output (S0) do?

The S0 output generates a pulse for every 1 Wh (0.001 kWh) consumed, allowing connection to external monitoring systems or energy management controllers.

Is there a troubleshooting guide for error codes?

Error codes are displayed as 'Err' followed by a number. Common errors: Err1 (overvoltage), Err2 (overcurrent). Consult the manual for full list. Contact support if persistent.

What is the warranty period for this product?

Vemer typically offers a 2-year warranty from the date of purchase. Check your invoice or contact your dealer for details.

Can the meter be used outdoors?

The front has IP20 protection, so it should be installed in a weatherproof enclosure if used outdoors. The terminal block is IP50 for basic dust protection.

How do I clean the meter?

Disconnect power and wipe the exterior with a dry, soft cloth. Do not use solvents or water. Do not attempt to open the device.

USER MANUAL ADR-D 230 D63 Vemer

Read all instructions carefully

■ Single-phase system analyser for TRMS (True Root Mean Squared) values. Pulse output for direct connection of a current lead with I_MAX = 63A . Connection is effected by directly inserting the power lead vertically into the housing.

SAFETY INSTRUCTIONS

To guarantee correct installation, observe the following instructions: 1) The instrument must be installed by a qualified person 2) The instrument must be installed in an electrical panel which, after installation.

3) The instrument must be installed in an electrical panel unit, after installation, leaves terminals inaccessible 3) The building in which the instrument is installed must have an electrical system including a switch or a circuit breaker this must be near the device and in a position that can be easily reached by operators 4) A protection device against over-currents must be installed in the electrical system upstream of the instrument

5) Connect the instrument as shown in the diagrams of this manual
6) Before making contact with terminals, ensure that leads to be connected to the instrument are not live
7) Do not power or connect the instrument if any part of it is damaged

Note: The network analysers in the ADR-D 230 D63 series are aimed for use in places with overvoltage category III and pollution degree 2 to EN 61010-1.

Code Model Description

VE035200 ADR-D 230 D63 Single-phase network analyser

TECHNICAL SPECIFICATIONS

- Power supply/Input voltage: 230V AC (-15%/+10%) 50/60Hz - Input Current: I s = 10A; I max = 63A by direct connection - Galvanic insulation between voltage and current inputs - Maximum cross-section of the current lead: 25 mm ^3 - Maximum diameter of the perforation for the current lead: 12.5 mm - Maximum consumption (device only): voltage circuit <2.5 VA power circuit <2.5 VA power supply < A VA

• Quantities measured: Voltage (Page 1)

Current (Page 2)

Active power (Page 3)

Power factor (Page 4)

Frequency (Page 5)

• Operating temperature: -10 ÷ +45^

- Operating temperature: -10 ± +45 °C - Relative humidity: 10% ÷ 90% non-condensing

- Storage temperature: -20 ÷ +60^ C

• Signalling leds: green = power on

red = flashing at frequency 10Wh

- Optoinsulated pulse output: pulse duration = 100 ms ± 15%

pulse voltage = 9 ± 24 V DC (± 10%) maximum output current = 20 mA

• Display: LCD display, 7 + 5-digits

• Enclosure: 3 DIN, RAL 7035 gray

• Protection rating: IP20/IP51 on the front

RESOLUTION AND ACCURACY

• Alternating voltage: Maximum reading: 265.0V

Resolution: 0,1

Accuracy: ± IV ± 1 digit

• Alternating current: Maximum reading: 67.00A

Minimum reading: 0.10A

Resolution: 0,01A

Accuracy: ± 0,5% full scale ± 1 digit (full scale: 63A)

• Active power: Resolution: 0.01kW

Accuracy: +1% full scale + 1 digit (full scale: 100kW)

• Power factor: Resolution: 0.01

Accuracy: ± 1% ± 1 digit

• Frequency: Resolution: 0,1Hz

Accuracy: ± 0,1Hz (from 45Hz to 65Hz)

• Total active energy: Resolution: 0,1kWh (full scale: 999999,9 kWh)

Resolution: 1kWh (full scale: 999) Accuracy class 1 to EN 62053-21

- Partial active energy: Resolution: 0,01kWh (full scale: 999,99 kWh)

Resolution: 0,1kWh (full scale: 9999,9 kWh)

Accuracy: class 1 to EN 62053-21

DEVICE DESCRIPTION

① Backlit LCD display to read the values measured
② Open collector pulse output: 1 pulse every 0,1kWh count
③ Perforation for direct connection of current leads
④ Green LED: ON when the instrument is powered
⑤ Red LED: every flash corresponds to an energy count of 10Wh ⑥ Page scroll button, zeroing of partial meter, parameter set-up

OPERATION

The values measured are read over 6 pages to be scrolled using the SEL button.

Page 1	1076843^km	Total active energy meter
	2302^v	Alternating voltage value
Page 2	1076843^km	Total active energy meter
	805^A	Alternating current value

1076843 ^mWh	Total active energy meter
245 ^mm	Active power value

1076843 kWh	← Total active energy meter
087 PF	← Power factor value

Page 5

FrE9500

← Frequency value

1076843 kWh	← Total active energy meter
16392 kWh	← Partial active energy meter

To access the 2 pages reading only active energy counts, press the SEL button again.

Page 7	1076843 ^thm	← Non-zeroable total active energy meter
Page 8	16392 ^thm	← Zeroable partial active energy meter

The partial meter is automatically zeroed when the scale range is overrun. To set the meter to

zero manually, hold the "SEL" key down for more than 3 seconds

To view the first page again, press the SEL key once more.

BACKLIGHTING

The device's display backlights when the SEL key is pressed. it stays on for 30 seconds after the

last key is pressed.

To change this betting go to page 1 and hold down the BUB key for at least 6 seconds

Backlighting status (ON / OFF)

OPERATING MESSAGES

PHASE ERROR

On startup the device checks the connection of voltage terminals and the direction of the current lead. In case of error the phase error page will be displayed for 3 minutes. The triangular LED on the left will flash and the red signaling LED will be ON.

To resume correct operation, turn the device off, invert voltage connections or current lead direction and turn it back on.

Error conditions occurring during normal operation are indicated by the flashing of the triangu

← Error reading on start-up

lar LED on the left and the lighting up of the red signaling LED. Voltage, current and frequency values are nonetheless read correctly. As far the remaining nodes, average counts will not increase, the power factor will be found not to

As for the remaining pages, energy counts will not increase, the power factor will be force-set to

← Voltage value with Phase error LED

1 and the active power value to 0.

OVERFLOW ERROR

When the voltage or current reading range is overrun, the relevant field will flash dots and the total energy count will be read.

Voltage or current overflow error is indicated on the other pages too. in this case the values

Voltage page for V > 265V

measured will flash.

REFERENCE STANDARDS

Conformity to EU directives: 73/23/EEC amended by 93/68/EEC (Low Voltage Electrical Equipment) 89/336/EEC amended by 92/31/EEC and 93/68/EEC (E.M.C.) is declared with reference to the following harmonised standards: EN 61010-1 EN 61000-6-2 and EN 61000-6-3 EN 62053-21 and EN 62052-11

[Non-Text]