ZFC11JB - Freezer Zanussi-Electrolux - Free user manual and instructions

Product Type	Chest Freezer
Brand	Zanussi-Electrolux
Model	ZFC11JB
Capacity	110 liters
Energy Class	F
Annual Energy Consumption	220 kWh
Noise Level	40 dB
Climate Class	SN, N, ST, T
Voltage	220-240 V, 50 Hz
Power	100 W
Dimensions (H × W × D)	850 × 600 × 500 mm
Weight	30 kg
Freezing Capacity	10 kg/24h
Storage Time (power failure)	15 hours
Controls	Manual thermostat
Defrost	Manual
Features	Fast freeze function, temperature indicator
Refrigerant	R600a
Color	White
Warranty	2 years
Repairability	Spare parts available for 10 years

Frequently Asked Questions - ZFC11JB Zanussi-Electrolux

How do I install the freezer properly?

Place the freezer in a dry, ventilated area away from heat sources. Leave a gap of at least 10 cm around the sides for airflow. Level the freezer using the adjustable feet. Do not install in a damp or freezing environment.

What temperature should I set?

The recommended temperature for a freezer is -18°C or lower. Use the manual thermostat dial to adjust; typically, a mid-setting is suitable. Check with a thermometer for accuracy.

How often should I defrost the freezer?

Defrost when ice build-up exceeds 5-10 mm thickness. For manual defrost models, switch off the freezer, remove food, and let ice melt naturally. Clean and dry thoroughly before restarting.

How do I clean the freezer?

Unplug the freezer and remove all food. Wash interior with a mild detergent solution, rinse, and dry. Avoid abrasive cleaners. Clean the condenser coils at least twice a year to maintain efficiency.

Why is my freezer making unusual noises?

Normal sounds include clicking from the thermostat, humming from the compressor, and gurgling from refrigerant flow. If loud or persistent, check that the freezer is level, and that no parts are loose.

How can I save energy with my freezer?

Keep the freezer full (use bottles or blocks if empty), avoid frequent door openings, ensure door seals are clean and tight, defrost regularly, and place the freezer in a cool room away from heat sources.

What should I do if the freezer stops working?

Check if it's plugged in, if the circuit breaker has tripped, or if the thermostat is set correctly. If power is restored after an outage, wait 5 minutes before restarting to protect the compressor.

How do I replace the door seal?

Purchase the correct seal for your model. Remove the old seal by pulling it out from the groove. Clean the groove, then press the new seal firmly into place. Ensure a tight closure to prevent cold air loss.

Can I store hot food in the freezer?

No, hot food should be cooled to room temperature before freezing. Placing hot food raises the internal temperature, causing nearby items to thaw and increasing energy consumption.

What safety precautions should I follow?

Always unplug before cleaning or maintenance. Do not use extension cords. Keep ventilation openings clear. Do not damage the refrigerant circuit. If the power cord is damaged, replace it with an identical one from the manufacturer.

USER MANUAL ZFC11JB Zanussi-Electrolux

OPERATING AND INSTALLATION MANUAL

Important Safety Information

These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings or these warnings contact Expert Appliance Care.

Prior to Installation

Check the appliance for transport damage. Under no circumstances should a damaged appliance be installed. In the event of damage please contact your retailer.

Installation

• This appliance is heavy. Care should be taken when moving it.
• It is dangerous to alter the specifications or attempt to modify this product in any way.
• Ensure that the appliance does not stand on the electrical supply cable. If the supply cable is damaged, it must be replaced by a cable available from your Expert Appliance Care.
• Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
• Parts which heat up should not be exposed. Whenever possible, the back of the appliance should be close to a wall, but leaving the required distance for ventilation, as stated in the installation instructions.
• The appliance should be left for 2 hours after installation before it is turned on, in order to allow the refrigerant to settle.
• Make sure that the power plug is not squashed or damaged by the back of the fridge/freezer.

- A damaged power plug may overheat and cause a fire.

- Do not place heavy articles or the fridge/freezer itself on the power cord.

- There is a risk of a short circuit and fire.

- Do not remove the power cord by pulling on its lead, particularly when the fridge/freezer is being pulled out of its niche.

• Damage to the cord may cause a short-circuit, fire and/or electric shock.
• If the power cord is damaged, it must be replaced by a certified service agent or qualified service personnel.

- If the power plug socket is loose, do not insert the power plug.

- There is a risk of electric shock or fire.

Child Safety

• Do not allow children to tamper with the controls or play with the product.
• There is a risk of suffocation! Keep packaging material away from children!

During Use

• This appliance is designed for domestic use only, specifically for the storage of edible foodstuffs. It is not intended for commercial or industrial use.
• Containers with flammable gases or liquids can leak at low temperatures. Do not store any containers flammable materials, such as spray cans, fire extinguisher refill cartridges etc. in the refrigerator.
• Frozen food should not be refrozen once it has thawed out.
• Do not place carbonated or fizzy drinks in the freezer compartment
• Ice lollies can cause 'frost/freezer burns' if consumed straight from the freezer
• Do not remove items from the freezer compartment if your hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.
• Bottles and cans must not be placed in the freezer compartment they can burst when the contents freeze.
• Manufacturers' recommended storage times should be adhered to. Refer to relevant instructions.

Maintenance and Cleaning

• Before cleaning, always switch off the appliance and disconnect from the electrical supply.
• When unplugging always pull the plug from the mains socket, do not pull on the cable.

Servicing

- This product should be serviced by an authorised

engineer and only genuine spare parts should be used.

- Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact Expert Appliance Care.

At the end of the Appliance Life

• When disposing of your appliance use an authorised disposal site.
• Remove the plug and ensure that any locks or catches are removed, to prevent young children being trapped inside.

Contents

Instructions for the User

Important Safety Information 2

Description of the Appliance 4

Control panel 4

Operation

Before use 5

Starting the Appliance 5

Temperature Control 5

Opening/Closing the Lid 5

Freezing Fresh Food 5

Frozen Food Storage 5

Thawing 5

Hints and Tips

Normal Operating Sounds 6

Food Storage 6

Energy Saving Advice 6

In the Event of a Power Failure 6

Defrosting 7

Maintenance and Cleaning

Internal cleaning 7

External cleaning 7

When the appliance is not in use 7

Something Not Working 8

Service and Spare Parts 8

Instructions for the Installer

Technical Specifications 11

Installation

Positioning 11

Electrical Connections 12

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Description of the Appliance

A - Knob of temperature regulator
B - Compartment for frozen food storage and freezing fresh foods

Operation

Before Use

Remove all packaging and securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5m1 to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry thoroughly.

Starting the Appliance

Insert the plug into the wall socket.

Switching on freezer box

Close top of freezer box installed in accordance with specifications down then connect equipment with mains as specified above. At this time electric components inside will be energised.

Adjust knob of temperature regulator in centre with rotating clockwise. After a weak clicking cooling compressor will start together with slight vibration and noise.

1. Knob of temperature regulator

Opening/Closing the Lid

The lid is fitted with a tightly closing sealing strip to prevent moisture entering the freezer, increasing the amount of frost formed.

When the lid is opened the air inside the freezer becomes slightly warmer and expands. When the lid is closed again the air is cooled immediately. This may lead to the creation of a vacuum which makes it hard to open the lid again immediately. This is quite normal.

Wait for a few minutes until the vacuum has subsided and then open gently. Never use excessive force on the handle.

Top has closed and opened position. Movement over open position of top (about 95°) can cause damage.

Freezing Fresh Food

It is important that fresh food placed in the freezer is frozen quickly and that the food already in the freezer is heated as little as possible.

If more than 3-4kg of food is to be frozen:

- Turn the thermostat control knob to the coldest setting ("SUPER."). The freezer will now run continuously, creating a sufficient reserve of the temperature required.

• Turn the thermostat control knob 6-24 hours before placing new food in the freezer, depending on how much food is to be frozen.
• Place the food in the freezer and leave the thermostat set at "SUPER." for about 24 hours more.
• Then turn the thermostat control knob back again. The freezer will return to normal storage temperature.

If the thermostat control knob is accidentally left at the coldest setting the freezer will not be damaged, but energy will be wasted.

Frozen Food Storage

When first starting the freezer or if the freezer has been out of use for some time, we advise you to run your appliance for at least 2 hours before storing frozen food.

Do not exceed the storage period indicated by the manufacturer.

Do not open the lid frequently or leave it open longer than is necessary.

Important

Do not put carbonated liquids in the freezer.

Ice lollies, if consumed immediately after removal from the freezer can cause a low temperature skin burn.

Do not remove items from the freezer if your hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.

In the event of a power cut the food in the freezer will not be affected if the power cut is short and the freezer is full. Do not open the lid Should the food begin to thaw it must be consumed quickly and must not be re-frozen.

(See Hints and Tips)

Thawing

Deep frozen or frozen food, prior to being used, can be thawed in the fridge or at room temperature, depending on the time available. Small food items may even be cooked from frozen, in this case cooking will take longer.

Any frozen food which is allowed to thaw accidentally should either be eaten as soon as possible, or thrown away. Alternatively, if the food is uncooked and has not been completely defrosted it can be cooked and then refrozen.

⚠️ Defrosted cooked food must never be refrozen.

i Hints & Tips

Normal Operating Sounds

• You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils or tubing.
• When the compressor is on, the refrigerant is being pumped round and you will hear a whirring sound or pulsating noise from the compressor.
• A thermostat controls the compressor and you will hear a faint 'click' when the thermostat cuts in and out.

Food Storage

To obtain the best performance from your freezer:

• Do not store warm food or evaporating liquid.
• Avoid buying frozen food if you cannot store it straight away. The use of an insulated container is advisable. When you arrive home, place the frozen food in the freezer immediately.

- Do not push food together too much, try to allow air to circulate around each item.

- Do not store food uncovered.

- Ensure that food placed in the freezer is dated and labelled and used in date order to ensure that food is consumed at its best.

- Lean food keeps better and longer than fatty food, salt reduces the storage time.

- Wrap the food in polythene or aluminium freezing bags or foil so that they adhere to the food and provide an airtight seal.

- Packaging which is swollen or has traces of refrozen water droplets on the pack could indicate that the product has not been kept at a suitable temperature and that it may have lost its original quality. Partially thawed food must not be refrozen, it must be consumed within 24 hours. Never exceed the storage times indicated by the manufacturer.

Energy Saving Advice

• Do not install the appliance close to sources of heat, such as a boiler or radiator.

• Locate the appliance in a cool well ventilated room and make sure that the air openings of the appliance are not obstructed.

• Avoid unnecessary frosting in the cabinet by packing all foodstuffs into airtight packages before placing them in the freezer.

• Food which is to be frozen (when cool) should be placed in the fridge before being transferred to the freezer.
• Try to avoid keeping the lid open for long periods or opening the lid too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often.
• Ensure there are no obstructions preventing the lid from closing properly.

In the Event of a Power Failure

If there is a power failure during the storage of frozen foods, keep the lid closed. If the temperature within your freezer should rise, do not refreeze the food without checking its condition. The following guidelines should assist you:

Ice cream: Once thawed should be discarded.

Fruits & Vegetables: If soft should be cooked and used up.

Breads & Cakes: Can be refrozen without danger.

Shellfish: Should be refrigerated and used up quickly.

Cooked Dishes: i.e. casseroles should be refrigerated and used up.

Large Pieces of Meat: Can be refrozen providing there are still ice crystals remaining within them.

Small Joints: Should be cooked and can then be refrozen as cooked dishes.

Chicken: Should also be cooked and refrozen as a fresh dish.

Defrosting

The freezer compartment will become progressively covered with frost. This should be removed with the special plastic scraper provided whenever the thickness of frost exceeds 1 /4".

During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.

However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out and it is advisable to perform this operation when the appliance is empty.

To carry out complete defrosting:

1. Disconnect the freezer from the electricity supply.
2. Remove any stored food, wrap in several layers of newspaper and store in a cool place.
3. Leave the lid open.
4. To accelerate the defrosting process place a bowl of hot (not boiling) water inside the freezer and close the lid.
5. When defrosting is completed, dry the interior thoroughly.
6. Turn the thermostat control back to a medium setting between 3-4 and leave to run for at least 2 hours.
7. Replace the previously removed food.

Important

A temperature rise of the frozen food packs during defrosting may shorten their safe storage life.

Never use sharp metal tools to scrape off frost from the evaporator as this could damage the appliance beyond repair.

Maintenance and Cleaning

Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply

Internal Cleaning

Clean the inside and accessories with warm water and bicarbonate of soda (5m1 to 0.5 litre of water).

Rinse and dry thoroughly.

NEVER use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as these will damage the surface and leave a strong odour.

External Cleaning

Wash the outer cabinet with warm soapy water.

When the Appliance is not in Use

When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the lid open to prevent unpleasant smells.

Something Not Working

If the appliance is not working correctly, please carry out the following checks before calling out an engineer.

Defect:	Check if:	Possible cause:	Action:
Freezer not cold enough	Temperature of stored foods increases (becomes hotter).	Plug not connected correctly	Check plug and socket
		Defect in switch or fuse	Check fuse, call electrician
		Power failure	Wait until current returns
Too much frost formed	Lid does not close completely	Lid in contact with goods in freezer	Re-arrange goods, check that lid closes correctly
	Lot of moisture in the room	Moisture from washing machine, tumble-dryer, etc.	Move freezer to a room with less moisture, or air regularly
	Goods packed poorly	Lot of moisture from goods	Re-pack goods, see under “How to use”

If after all above checks there is still a fault, contact Expert Appliance Care.

In-guarantee customers should ensure that the above checks have been made, as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.

Please note that proof of purchase is required for any in-guarantee service calls.

Service and Spare Parts

If you require further information regarding teh appliance, the terms and conditions of the guarantee, or wish to call out an engineer, please contact Expert Appliance Care by telephoning:

0870 9099100

Technical Specifications

Model		ZFC 11JB
Volume (gross) litres		105
Volume (net) litres		102
Height without/with roller cm		85
Width	cm	55
Depth cm		59,3
Weight	kg	27
Energy consumpt./24h	kWh	0,684
Freezing capacity	kg/24h	12
Hold-over time	hours	26
Rated power	W	68

Installation

Positioning

• Place the freezer horizontally on a firm surface, resting on all four feet/wheels. Use a wooden block or similar object to compensate for any bumps/holes in the surface.
• The room should be dry and adequately ventilated.
• Temperatures of the external environment have an impact on the energy consumption of the device. Therefore:

-do not put the device to a place exposed to sunshine ore besides a radiator or oven,

-put it to a place where the temperature of the environment corresponds to the climatic classification for which the device was designed.

Climatic classification Ambient temperature limits

SN from +10°C to +32°C

N from +16°C to +32°C

ST from +18°C to +38°C

T from +18°C to +43°C

• If the freezer has been handled standing on end it should be allowed to stand in normal position for about 12 hours before switching it on.
• Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.

Electrical Connection

Any electrical work required to Install this appliance should be carried out by a qualified electrician or competent person.

This appliance must be earthed.

The manufacturer declines any liability should these safety measures not be observed.

Electrical Requirements

Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating

plate.

The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (B51362) fuse must be used. Should the plug need to be replaced for any reason. The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow : Earth

Blue : Neutral

Brown : Live

The wire coloured green and yellow must be connected to the terminal marked with the letter "E" or by the earth symbol or coloured green and yellow.

The wire coloured blue must be connected to the terminal "N" or coloured black.

The wire coloured brown must be connected to the terminal marked "L" or coloured red.

Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.

www.electrolux.com

www.zanussi-electrolux.co.uk.