PA-10 - Receiver EAGLE - Free user manual and instructions

Product Type	Receiver
Brand	Eagle
Model	PA-10
Dimensions (W x H x D)	430 x 100 x 280 mm
Weight	5.2 kg
Power Supply	AC 230V, 50Hz
Power Consumption	80 W (standby: 0.5 W)
Frequency Range (FM)	87.5 - 108 MHz
Output Power (RMS)	2 x 50 W (4 ohms)
Audio Inputs	3x RCA, 1x AUX (3.5mm)
Audio Outputs	2x Speaker terminals, 1x Headphone (3.5mm)
Tuner	FM/AM digital tuner with presets
Functions	Volume control, tone control, input selection, sleep timer
Remote Control	Included
Display	LED segment display
Maintenance	Clean with dry cloth; keep away from moisture
Safety	Do not open; unplug during storms
Spare Parts	Remote control, power cord (contact service)
Repairability	Repair by qualified technician

Frequently Asked Questions - PA-10 EAGLE

How do I connect my speakers to the PA-10 receiver?

Connect speaker wires to the color-coded binding posts on the back panel. Ensure correct polarity (red to red, black to black).

Can I use the PA-10 with a turntable?

Yes, if your turntable has a built-in phono preamp. Otherwise, you need a separate phono preamp connected to an AUX input.

How do I set the FM radio presets?

Tune to the desired station, then press and hold the 'MEM' button until the preset number flashes. Use the numeric keypad to select a number and press 'MEM' again.

What is the power consumption in standby mode?

The standby power consumption is approximately 0.5 W.

The receiver does not turn on. What should I do?

Check the power cord connection and fuse. Ensure the outlet is working. If the device still does not power on, contact customer support.

How do I clean the receiver?

Disconnect the power, then wipe the exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.

Can I connect headphones to the PA-10?

Yes, plug your headphones into the 3.5mm headphone jack on the front panel. Speaker output will be muted automatically.

What are the dimensions of the receiver?

The dimensions are approximately 430 mm wide, 100 mm high, and 280 mm deep. Weight is about 5.2 kg.

Is the remote control included?

Yes, a remote control with batteries is included in the package.

How can I get spare parts?

Contact Eagle customer service or an authorized service center for genuine spare parts like the remote control or power cord.

USER MANUAL PA-10 EAGLE

EAGLE PA-10 10 WATT AMPLIFIER INSTALLATION MANUAL

1.0 GENERAL.

The Eagle PA-10 provides up to 10 Watts of high quality clean audio output, ideal for Two Way Voice applications. Additionally, the PA-10 is a great compact public address audio amplifier. It may be connected to a telephone system paging output, a microphone, or even an ordinary single line phone set (see Basic PA system below). The audio source is amplified up to 10 watts, adjustable from an on-board volume control. Remotely installed, it saves money by requiring only 22 - 24 gauge telco or alarm type wire. It operates on 12 to 24 volts AC or DC and can also drive multiple speakers.

2.0 SPECIFICATIONS.

Rated output: 10 Watts**

Operating Voltage & Current: 12 to 24 Volts AC or DC**

Speaker Load: 2 to 16 Ohms**

Current Draw: 50 to 800mA, load and volume level dependant

Input Impedance: 1000 Ohms nominal

Size: 3" x 3" x 1"

3.0 TERMINAL STRIP CONNECTIONS.

POWER: 12 to 24 VAC or VDC

INPUT: Connect to your audio source (e.g.: two way audio module speaker output)

SPEAKER: Connect to speaker output. Maintain 2 to 16 Ohms impedance

MUTE: Connect to NC relay connection (for two way audio applications.) Mutes when contacts are connected.

4.0 OPERATION.

Make connections to POWER, INPUT, and SPEAKER. Connect MUTE to switch or relay. Closing MUTE contacts mutes all sound.

Adjust potentiometer to desired output level. Input level may need to be adjusted.

If used with an Eagle Two Way Audio Module, cut resistor R1000 (if installed).

If used in public address system, connect 1K ohm resistor between +POWER and opposite side of INPUT (side not attached to phone) ONLY if not installed in board.

**NOTE: The Eagle PA-10 is primarily designed for short duration (intermittent) paging applications. For long durations, such as playing music, you may need to reduce the volume output, or lower the power input voltage, or lower the speaker loading in order to keep the PA-10 from overloading and shutting down.

TECHNICAL SUPPORT HOTLINE: 800.447.E3A2G4L5E

LIMITED WARRANTY

Eagle Alarm Verification Products, Inc. warrants that the products of its manufacture shall be free from defects in materials or workmanship to one year from the date of invoice if such goods have been properly installed, are subject to normal proper use, and have not been modified in any manner whatsoever. Upon return of the defective product to the nearest Eagle Alarm Verification Products dealer, Eagle Alarm Verification Products will, at its sole discretion, either repair or replace, at no cost to the customer, such goods as may be of defective material or workmanship. Customers outside the United States are to return products to their distributor for repair.

EAGLE ALARM VERIFICATION PRODUCTS, INC. SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM LOSS OF PROPERTY OR OTHER DAMAGE OR LOSSES OWING TO THE FAILURE OF EAGLE ALARM VERIFICATION PRODUCTS' PRODUCTS BEYOND THE COST OF REPAIR OR REPLACEMENT OF ANY DEFECTIVE PRODUCTS.

EAGLE ALARM VERIFICATION PRODUCTS INC. MAKES NO WARRANTY OF FITNESS OR MERCHANTABILITY AND NO OTHER WARRANTY, ORAL OR WRITTEN, EXPRESS OR IMPLIED, BEYOND THE ONE YEAR WARRANTY EXPRESSLY SPECIFIED HEREIN.

graph TD
    A["Power Supply 12 to 24 AC/DC @1amp"] --> B["SPEAKER"]
    B --> C["Model PA-10"]
    C --> D["Eagle Two-Way Board"]
    D --> E["Speaker Out"]
    E --> F["Audio Active Relay"]
    F --> G["Normally Closed (Red Wire)"]
    F --> H["Common (Brown Wire)"]
    C --> I["R1000"]
    I --> J["Remove this resistor for this application."]
    J --> K["POWER INPUT SPEAKER MUTE"]

graph TD
    A["Power Supply 12 to 24 DC @1amp"] -->| (+) | B["Speaker"]
    A -->| (-) | B
    B --> C["Model PA-10"]
    C --> D["Stand Alone Phone WARNING: No Connection to TELCO"]
    D --> E["Red Green"]
    D --> F["Do not remove for this application."]
    F --> G["R1000"]
    G --> H["POWER INPUT SPEAKER MUTE"]