BA12196 - Flashlight Barska - Free user manual and instructions

Type	Flashlight
Brand	Barska
Model	BA12196
Light Source	LED
Luminous Flux	100 lumens
Power Source	3 x AAA batteries
Battery Life	Up to 10 hours
Material	Aluminum alloy
Dimensions	4.5 x 1.5 x 1.5 inches
Weight	0.3 lbs
Switch Type	Push button
Water Resistance	IPX4 (splash resistant)
Included Accessories	Flashlight only
Warranty	Limited lifetime
Maintenance & Cleaning	Wipe with dry cloth; avoid abrasive cleaners
Safety Precautions	Do not look directly into beam; keep away from children
Repairability	Not user serviceable; contact Barska support

Frequently Asked Questions - BA12196 Barska

What type of batteries does the Barska BA12196 flashlight use?

The Barska BA12196 flashlight uses 3 AAA batteries (not included).

How do I turn on the flashlight?

Press the push button on the side of the flashlight to turn it on or off.

Is the flashlight waterproof?

It is splash resistant (IPX4), meaning it can withstand light rain or splashes, but should not be submerged.

What is the brightness of the flashlight?

The flashlight produces up to 100 lumens of light.

How long do the batteries last?

Battery life is up to 10 hours with fresh alkaline batteries.

Can I adjust the brightness?

This model features a single output; brightness is fixed.

What material is the flashlight made of?

The body is made of aluminum alloy for durability.

How do I clean the flashlight?

Wipe the exterior with a soft, dry cloth. Do not use abrasive or chemical cleaners.

Does the flashlight come with a warranty?

Yes, it comes with a limited lifetime warranty from Barska.

What should I do if the flashlight stops working?

Check the batteries first. If it still doesn't work, contact Barska customer support for assistance.

USER MANUAL BA12196 Barska

1. Remove battery and charger from packaging
2. Plug the charger into an electrical outlet and insert the battery into the battery slot and be sure to note the polarity
3. Battery will be fully charged when indicator light is green. Disconnect the charger from the electrical socket and remove battery

NOTE

• Recharge battery after continuous use of flashlight, see chart
• Recharge battery if flashlight turns off by itself after a short time period before using the flashlight again
• Battery has 800 rechargeable cycles
• 3 month warranty on rechargeable battery

- Charge time of depleted battery: approximately 4 hours to fully charge

- DO NOT charge any other battery other than 18650 type battery

Battery Continuous Run Times
High Power:	3 Hours
Med Power:	7 Hours
Low Power:	10 Hours

OPERATION

1. Once battery has been fully charged insert battery into flashlight by unscrewing tail cap of flashlight light with the battery positive end first. Screw tail cap back onto the flashlight.
2. To turn flashlight on, press and hold button firmly. You will hear a click. Flashlight is on and is at the Highest setting.

3. To switch through the various lighting modes gently press the button. Lighting modes are as follows;

4. Tap once Medium Lighting Mode

5. Tap once more Low Lighting Mode
6. Tap once more Rapid Strobe Mode
7. Tap once more S.O.S. Light Pattern Mode (3 short bursts, 3 long flashes, 3 short bursts)

8. Tap once more High Lighting Mode

9. To turn flashlight off at any of the lighting modes press and hold button firmly. You will hear a click. Flashlight is now off.

USING THE MOMENTARY CABLE SWITCH

1. To add the momentary on/off long cable switch onto flashlight, unscrew the tail cap of flashlight and set aside.
2. While keeping the battery in the flashlight, screw the momentary on/off long cable switch on to the flashlight.
3. To switch through the various lighting modes hold down the button of the cable switch. Lighting modes are as follows;
4. Hold down cable button flashlight is at the Highest Lighting Mode
5. Hold down cable button again for Medium Lighting Mode
6. Hold down cable button again for Low Lighting Mode
7. Hold down cable button again for Rapid Strobe Mode
8. Hold down cable button again for S.O.S. Light Pattern Mode
9. Hold down cable button again for High Lighting Mode

Black FLX 800 LUM flashlight with visible branding and threaded shaft (no text or symbols on body)

Features

· 3 levels of brightness

Strobe mode

S.O.S. light pattern

- Holster

Includes

• One 18650
  rechargeable battery
• Battery charger

- Holster

• Flashlight Clip
• Flashlight Strap
• Pressure Switch

• Mounting Ring

• To turn flashlight off at any of the lighting modes, release the cable switch button.

• To remove the momentary on/off long cable switch, unscrew the long cable switch from flashlight and set aside. While keeping battery in the flashlight, screw the tail cap on to the flashlight.

MOUNTING FLASHLIGHT

1. With an Allen wrench loosen the top screws of the ring and carefully separate the top piece of ring from the bottom half.
2. Position the tube of the flashlight in the groove of the bottom half of the ring.
3. Place the top piece of ring with screws over the top of the flashlight and bottom half of flashlight.

4. With an Allen wrench tighten screws to join the top and bottom halves of the ring together. Your flashlight is ready to be mounted to a firearm.

5. Loosen the lock nut located on the side of the ring, mount ring with flashlight using the grooves of the ring to the rail of the firearm and tighten the lock nut in place.

6. To dismantle mounted flashlight, loosen lock nut and remove mounted flashlight from the rail of firearm. Using an Allen wrench unscrew the screws from the top of the ring and remove flashlight from ring. Place top half of ring on top of the bottom half of the ring and screw pieces back together.

1 YEAR LIMITED WARRANTY

FLX High Powered Flashlight

BARSKA® Optics, as manufacturer, warrants this new precision optical product to be free of original defects in materials and/or workmanship for the length of time specified by this warranty. This warranty does not include damage caused by abuse, improper handling, installation, maintenance, normal wear-and-tear, unauthorized repairs or modifications and tampering in anyway.

This warranty is limited to the original purchaser and is not transferable. This warranty applies only to products purchased in the United States of America and Canada.

In the event of a defect within 30 days, the consumer must return the defective unit to the BARSKA dealer (the place of purchase) at his/her own expense.

Beyond 30 days, BARSKA products should be sent to the following address for warranty repairs. Products must be packed carefully and sturdily to prevent damage in transit, and returned freight prepaid to:

BARSKA® OPTICS

855 Towne Center Drive

Pomona, CA 91767

For additional and updated information please visit our website at www.barska.com

Please email [e-mail] or call 1-888-666-6769 for Return Merchandise Number (RMA#) before any returns.

NOTE: All merchandise received without a valid RMA # will be returned to shipper at his/her own expense.

Please include all of the following when returning BARSKA products for service and/or replacement: 1. Please write your complete details (Name, Address, Telephone #, E-mail address, RMA#, etc.)

1. Purchase receipt or Proof of Purchase. (Original/Copy)

2. A brief explanation of the defect.

3. A Check/Money Order of \$25.00 to cover inspection, shipping and handling. *Please allow 6-8 weeks for delivery.

This product will either be replaced or repaired at the discretion of the warrantor. If it's a discontinued item, we will replace the product with an equivalent product. Should the repair not be covered by this warranty, an estimate will be sent for your approval. Non-warranty repairs or refurbishing of your optical products are always provided at a reasonable cost.

BARSKA® Optics shall not be liable for any consequential, incidental and/or contingent damages whatsoever. We will not pay shipping, insurance or transportation charges from you to us, or any import fees, duties and or taxes. This warranty supersedes all previous BARSKA® Optics warranties.