Tetragon HD 8 - Tent EUREKA - Free user manual and instructions

Product Type	Tent
Brand	Eureka
Model	Tetragon HD 8
Capacity	8 persons
Dimensions (Floor)	Approximately 16 x 10 ft (4.9 x 3.0 m)
Center Height	Approximately 6.5 ft (1.98 m)
Weight	Approximately 25 lbs (11.3 kg)
Material - Rainfly	Polyester with polyurethane coating
Material - Floor	Polyethylene (PE)
Poles	Fiberglass
Doors	2
Windows	2 with mesh
Ventilation	Mesh roof and zippered vents
Setup Type	Freestanding dome tent
Waterproof Rating	Fly: 1500mm, Floor: 2000mm
Storage Pockets	Yes, interior pockets
Includes	Tent body, rainfly, poles, stakes, carry bag
Care Instructions	Clean with mild soap, air dry completely, store in dry place
Safety Warning	Never use stoves or flames inside tent
Spare Parts Available	Poles, stakes, replacement parts from Eureka

Frequently Asked Questions - Tetragon HD 8 EUREKA

What is the capacity of the Eureka Tetragon HD 8?

The Tetragon HD 8 is designed to accommodate up to 8 persons comfortably.

Are the poles included with the tent?

Yes, the tent comes with fiberglass poles that are shock-corded for easy setup.

How do I set up the Tetragon HD 8 tent?

The tent is a freestanding dome. Lay out the tent body, assemble the poles, and insert them through the sleeves or clips. Then attach the rainfly and stake out as needed.

What is the waterproof rating of the rainfly?

The rainfly has a 1500mm waterproof rating, and the floor has a 2000mm rating.

Can I use a stove or heater inside this tent?

No, using stoves, heaters, or any open flame inside the tent is dangerous and can cause fire or carbon monoxide poisoning.

How do I clean and maintain my tent?

Clean with mild soap and water, rinse thoroughly, and allow it to air dry completely before storing. Avoid machine washing.

What is the center height of the Tetragon HD 8?

The center height is approximately 6.5 feet (1.98 m), allowing most people to stand upright.

How many doors does this tent have?

The tent features 2 doors for easy entry and exit.

Are spare parts available for the Tetragon HD 8?

Yes, you can purchase replacement poles, stakes, and other parts from Eureka or authorized dealers.

What should I do if a pole breaks during setup?

You can use a pole repair splint (often included) or replace the broken section with a spare part. Contact Eureka support for replacements.

USER MANUAL Tetragon HD 8 EUREKA

Eureka! Set-Up Instructions

Tetragon HD 2 (#2629132)

Tetragon HD 3 (#2629142)

Tetragon HD 4 (#2629152)

Tetragon HD 5 (#2629162)

Tetragon HD 8 (#2629172)

Contents of Carry bag

Tent body

Tent fly

Pole Bag: 2 long main poles, 2 shorter fly rods

Stake Bag: Stakes

Eureka! Media Center

Fabric Divider Curtain (#2629172 Tetragon HD 8 ONLY)

Setting up the Tent Body

1. Spread out the tent body, floor side down. Locate the yellow webbing corner loop, as this marks the front right hand corner of the tent.

2. Assemble the two long main poles by inserting each pole section into the corresponding metal ferrule.

3. 2629172 Tetragon HD 8 ONLY – Carefully push an assembled pole section through the fabric pole sleeve. Repeat with the second pole section.

4. Starting at the corner with the yellow webbing, insert the pins into the bottom ferrules. Then place the pole diagonally across the tent. From the opposite corner, apply pressure to pole to bend it and insert the pole end into the corresponding metal pin. Repeat this process with second long main pole by securing one into the corner metal pin before then securing the opposite end.

1. Raise the two main poles and attach the tent where the poles cross, using the fabric loop and toggle.

2. Walk around the tent and attach the tent body to the poles by clipping each of the black plastic fasteners.

3. Assemble the two short length fly rods by inserting each pole section into the corresponding metal ferrule.

4. Lay out the fly with the bottom side up. Insert the fly rods into the rod pockets. Wrap the hook & loop tabs around the rods.

Attaching the Fly Sheet

1. Locate the yellow webbing end corner of fly sheet to indicate the front right corner orientation.
2. Turn the fly over and drape it over and drape it across the tent so that the yellow webs meet. Aligning and centering the fly on the tent body so the four bungee cord with J-hooks mate with the stake out loops and metal pins at each four corners of the tent.
3. Ensure that all 4 bungee cords with J-hooks from the fly are clipped to each of the four tent corners ring.
4. We recommend always using the guy out cords to secure your tent, as weather conditions may change rapidly. Tie the guy lines to the webbing loops on each side of the fly and at each of the four corner poles (Tetragon HD 2/3/4 NOT SUPPLIED) of the tent and secure this line to a staked out position or nearby object.

Exterior view of a modern camping tent (no signage or text visible)

Tetragon HD 4

EUREKA! Media Center:

Watch video on tablets & other small electronics from the comfort of your sleeping bag. The clear center panel of the Media Center is touchscreen friendly. The Media Center attaches with hooks to pre-installed webbing loops located in each corner of the tent.

Exterior view of a white camping tent with visible seams and a label 'Tetragon HD 8' at the bottom (no other text or symbols)

Tetragon HD 8

REV 091415

WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT!

This tent meets the flammability requirements of CPAI-84. The Fabric may burn if continuous contact with any flame source. Do NOT operate any device which burns fuel inside your tent. This could lead to serious injury or death.

SEAM SEALING:

We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor SeamGrip®.

• Work in a fully ventilated area.

- Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer.

- Decide which seams need to be sealed. For example, seams that will be exposed to rain, runoff, or ground level water are a must for sealing, while seams on uncoated nylon or mesh panels don't need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements.

- Apply sealant to the inside and outside of all exposed seams. Several thin layers will work better than one thick layer. Read and follow manufacturer's instructions.

STAKING:

All tents need to be staked down to keep them from blowing away. Securing the tent by placing heavy objects inside is just not adequate.

- Once the tent body is erected, stake it out before the fly is put on. This enables you to square the tent up to ensure that the fly goes on properly and that the seams align with the frame. Pull the base of the tent taut between each web stake out loop or ring & pin. Make sure that all corners are square. It is important that you don't stake the tent out too tightly. You will know it's too tight, if the door zippers can not be easily operated. Drive stakes through the web loops, or with ring & pin, drive the stake just outside the ring so that the "J" hook catches it. Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed.

- With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs.

- Do not attempt to remove the stakes by pulling on the tent stake-out loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. STAKING IN SPECIAL CONDITIONS:

- Sand. Use long, broad stakes with plenty of surface area in loose soil.

- Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent.

- Snow. Use "dead man" anchors. Tie tent to buried objects (branches, tent bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski poles, which are stuck in the snow.

GUY LINES:

Do not depend upon staking alone to keep your tent secure during high winds. Most tent modes have built-in loops or rings at optimal guy out locations. It's important to put in the extra time guying out your tent. Correctly done, it can save your tent during exceptional weather.

- Make sure that the top fly is securely attached to the tent frame. Ties, hook and loop, or dog-bones and elastic loops are sewn to the underside of the fly for this purpose.

- Attach parachute cord to the loops/rings and stake them in the ground three or four feet from the edge of the tent. If staked too close to the tent, wind can cause an upward pull that could dislodge the stakes.

- If your tent does not have loops or rings for guy outs, attach guy lines 1/3 to 1/2 of the way up the framework on the main sidewalls. This enables the guy line to support the lower section of the pole, while the upper pole can flex and deflect wind gusts. It is best to run two cords at an angle from the side of the guy out. This prevents all movement, except toward the anchor. The guy lines will work together through opposition. See illustrations.

CONDENSATION & VENTING:

Through perspiration and breathing, an adult gives off about a pint of water overnight. If it cannot escape, the water vapor condenses to liquid. Most often, water found in the tent is a result of this condensation rather than from the tent leaking. Condensation often forms where the sleeping bag touches the side of the tent, under the sleeping pad, or on coated surfaces such as the door flaps. A tent's double wall construction allows the vapor to escape through the roof to the outside, keeping the inside of the tent dry.

Leave the windows partially open at night to provide cross ventilation and further reduce condensation. Cross ventilation becomes more important in very humid or extremely cold conditions when the permeable roof is less effective. The features that enhance ventilation are windows, short-sheeted flys (bottom venting), roof vents, and High/Low venting doors. These are specific to each tent model.

Given the importance of proper ventilation, We use High/Low venting in most of our tents. This allows cooler air in through the low vents and warmer, moist air up and out through the high vents. High/Low venting is accomplished within the inner tent via roof vents, doors and windows. It is important to vent the vestibule. Unvented, it can inhibit airflow into the tent. Our tent vestibules profit from the ability to "short sheet" by means of zippers & toggles and staked vestibule pull outs create a bellowing effect.

Most of our tents are equipped with a High/Low venting door. This design allows increased airflow into the tent from the bottom. Open the low vent/window to admit cool air, allowing the warmer air out through the high roof vents. When rain and wind prevent the low vent from being opened, the high door vent can still be used. Fly overhangs or vestibules protect it. ULTRAVIOLET LIGHT:

Ultraviolet light damage to tent fabric is caused by excessive exposure to sunlight. While our fabrics are UV resistant, any synthetic fabric is susceptible to UV degradation. UV damage will cause nylon and polyester to become brittle and tear easily. We recommend that you use the rain fly even on clear days. It acts as a sunscreen to the tent. A rain fly is both easier and less expensive to replace if damaged. UV damage can be minimized by erecting tents on shaded sites with low exposure to direct sunlight.

GENERAL POLE CARE:

- Never let tent poles snap together as this can damage the pole end. - Do not drop tent or pole bags on their ends and do not bounce a tent bag on its end to get the tent out. These actions may cut the shock cord and damage the pole ends.

- The aluminum frame may bend slightly and take a "set" through usage, this normally does not affect the performance of the frame.

GENERAL TENT CARE:

- Sweep the tent floor daily to prevent damage from stones.

• Try not to wear shoes inside your tent.

- Use a ground cloth whenever possible.

- Do not keep food inside a tent. Hungry critters will chew through tent fabric in search of food.

STORAGE:

- Make sure the tent is completely dry, then store loosely rolled, in a dry, cool place. To prevent dust from collecting on the tent, cover it with a cloth. This allows the nylon/polyester fabric to breathe.

- Ideally, the tent poles should be stored in their fully assembled state. This reduces the tension on the shock cord, prolonging its life.

• The tent bag should be used only as a carry sack and not for storage. COLOR TRANSFER:

- Do to the nature of tent fabrics, color can transfer from darker to lighter fabrics when the two fabrics are in contact over time when wet, damp or exposed to the combination of moisture and high heat. This does not effect the tent's performance. To prevent / minimize color transfer, always make sure your tent is completely dry prior to packing and storage.

CLEANING

- Clean the tent by setting it up and wiping it down with a mild soap (liquid hand soap) and lukewarm water solution. Rinse thoroughly and dry completely. Never use detergent, washing machines or dryers because they can damage the tent's protective coating and seams. After cleaning, be sure the tent is completely dry, especially the heavier, double-stitched areas such as the seams, before storing or mold / mildew are likely to grow.

- Clean the tent poles with a cloth and lubricate them with silicone spray. This is especially necessary after ocean side camping to remove salt spray so the poles don't corrode or stay gritty.

- Clean the zippers with a quick dip in water and then dry them off. This is especially important if you've been camping in a location with sand/dirt. If you don't clean the zippers, the sliders will wear out and eventually the teeth will become inoperable.

ALTERATIONS OR MODIFICATIONS:

DO NOT misuse, modify or alter this product in any way from its condition at the time of sale. Alteration, modification or any use of this product contrary to the accompanying written instructions shall void the warranty. Moreover, any misuse, alteration or modification of the product shall absolve Johnson Outdoors Gear, Inc. of any liability for property damages or injuries sustained as a result of such misuse, modification or alteration.

LIMITED WARRANTY:

What Is Covered: Johnson Outdoors Gear, Inc. warrants to the original purchaser that its products are free from defects in material and workmanship, for the life of the product, except as qualified below. The life of the product is determined from the date of purchase until such time as the product is no longer serviceable due to normal wear and tear.

What Is Not Covered: Johnson Outdoors Gear, Inc. shall not be responsible for the natural breakdown of materials that occurs inevitably with extended use (e.g., Ultra Violet (UV) light damage on tents, exhausted zippers), or defects caused by accident, abuse, alteration, animal attack, storm damage, misuse or improper care.

THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS LIMITED WARRANTY.

IN NO EVENT SHALL JOHNSON OUTDOORS GEAR INC. BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

What Johnson Outdoors Gear, Inc. Will Do: If after inspection we find that a product failed due to a manufacturing or material defect, we will repair or replace the product, at our option, without charge.

How to Obtain Warranty Service: Return the product, freight prepaid, to the Dealer from whom it was purchased; or, contact our Customer Satisfaction Department for return authorization; toll free 1-800-572-8822. Collect shipments or shipments without return authorization cannot be accepted. The product registration card packaged with our product need not be returned for the warranty to be effective and for you to receive warranty service.

Repairs. If your Johnson Outdoors Gear, Inc. product needs service or repair due to normal wear and tear, animal attack, accident or some other reason that is not covered under the warranty we will provide the necessary service for a reasonable charge, plus shipping and handling. We require that products accepted for any repair be properly cleaned according to our recommended care instructions. Please send your product or component that requires repair (e.g., tent fly), postage prepaid, along with a description of what needs attention. For service and repairs, please contact our Customer Satisfaction Department: toll fee 1-800-572-8822

How State Law Relates To This Warranty: This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

JOHNSON OUTDOORS JOHNSON OUTDOORS GEAR INC

Our brands are part of the Johnson Outdoors family of products. Visit all the brands at johnsonoutdoors.com

We support the "Leave No Trace" Seven Principles:

1. PLAN AHEAD AND PREPARE

2. TRAVEL & CAMP ON DURABLE SURFACES

ISPOSE OF WASTE PROPERLY

1. LEAVE WHAT YOU FIND

2. MINIMIZE CAMPFIRE IMPACTS

3. RESPECT WILDLIFE

4. BE COURTEOUS OF OTHER VISITORS

REV 091415