CS221CS - Styler Conair - Free user manual and instructions

Product Type	Hair Styler (Curl/Straight)
Brand	Conair
Model	CS221CS
Dimensions	10 x 2 x 3 inches
Weight	0.5 lbs
Power	25-50 Watts
Voltage	120V (Dual voltage: No)
Cord Length	6 feet
Heat Settings	1-2 settings
Max Temperature	400°F
Auto Shut-Off	No (manual)
Swivel Cord	Yes
Cool Tip	Yes
Barrel Material	Ceramic / Tourmaline
Warranty	2 years limited
Cleaning	Unplug and wipe with damp cloth
Safety	Do not immerse in water; use on dry hair only
Spare Parts	None available separately
Repair	Non-repairable, dispose accordingly

Frequently Asked Questions - CS221CS Conair

How do I choose the right heat setting on the Conair CS221CS?

For fine or damaged hair, use the low setting (around 300°F). For normal hair, medium (350°F). For thick or coarse hair, high (400°F). Always start with a lower heat and increase if needed.

Can I use the styler on wet hair?

No, always use on dry hair to prevent damage and electric shock. Towel-dry and fully dry your hair before styling.

How do I clean the styler?

Unplug the device and let it cool. Wipe the barrel and exterior with a damp cloth. Do not use abrasive cleaners or immerse in water.

Does the Conair CS221CS have a cool tip?

Yes, the styler is equipped with a cool tip that stays cool to the touch for safe handling while styling.

What is the cord length?

The cord is approximately 6 feet long, allowing for some flexibility during use.

Is this styler dual voltage?

No, the Conair CS221CS is designed for 120V outlets only. Do not use with voltage converters unless specified otherwise.

How long does it take to heat up?

It heats up quickly, typically within 30-60 seconds to reach the desired temperature.

Can I use hair products with this styler?

Yes, you can use heat-protectant sprays or styling products. Apply product to dry hair before styling to reduce heat damage.

What should I do if the styler stops working?

Check if it's properly plugged in and the switch is on. If it still doesn't work, contact Conair customer service. Do not attempt to repair it yourself.

How do I store the styler safely?

Allow the styler to cool completely, then wrap the cord around the handle (not tightly) and store in a dry, safe place away from children.

USER MANUAL CS221CS Conair

FAMILIARICSE COU SU PLANCHA ALISADORA

enceder el aparato.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER

KEEP AWAY FROM WATER DANGER

DANGER — Any appliance is electrically live even when the switch is off. To reduce the risk of death by electric shock:

1. Always unplug appliance immediately after using.

2. Do not use while bathing or in the shower

3. Do not place or store appliance where it can fall or be pulled into a tub or pink.

4. Do not place in, or drop into water or other liquids.

5. If an appliance falls into water, unplug it immediately. Do not reach into the water

WARNING

burns, electrocution, fire, or injury to persons:

1. This appliance should never be left unattended when plugged in.

2. Do not pull, twist, or wrap line cord around appliance.

3. This appliance should not be used by, on or near children or individuals with certain disabilities.

4. Use this appliance only for its intended use, as described in this manual. Do not use attachments not recommended by the manufacturer.

5. Never operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has been dropped or damaged, or dropped into water. Return the appliance to an authorized service center of communication and repair.

for examination and repair. 6. Keep the cord away from heated surfaces. 7. Never use while sleeping. 8. Never drop or insert any object into any opening.

1. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

2. Unit is hot when in use. Do not let heated surfaces touch eyes or skin.

3. Do not place the heated unit directly on any surface while it is hot or plugged in.

4. Never block the air openings of the appliance or place it on a soft surface, such as a

bed or couch, where the air openings may be blocked. Keep the air openings free of hair, lint and other debris.

1. Do not use an extension cord with this appliance.

2. Do not touch hot surfaces of the appliance. Use handles or knobs.

3. Do not attempt to touch the housing of your appliance near the straightening plates, as it is hot when in use.

4. Do not use with a voltage converter.

5. This appliance is not a toy. Keep away from children.

SAVE THESE INSTRUCTIONS

OPERATING INSTRUCTIONS

This flat iron is intended for household use. Use on Alternating Current (60 hertz) only. This unit is designed to be operated at 120 volts AC.

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

NOTE: Do not use this styling appliance on hair extensions.

STYLING WITH THE NEW EASY-GLIDE, FLOATING DOUBLE CERAMIC PLATE

The easy-glide Double Ceramic surface is one of the latest and best technological advances in hair appliances. With a higher ceramic content the Double Ceramic plates deliver even heat for the ultimate in silky, shiny, healthy-looking hair. You'll find that hair glides easily over the surface of the plates as you're straightening, and that it is easier to clean styling product residue, etc., off the plates after each use. The ceramic surface also helps smooth down flyaways. Your new straightening iron has a plate designed with a little give, to "float." This provides better contact with hair, eliminating gaps, for straighter results.

INSTANT HEAT TECHNOLOGY

This styling iron features a powerful PTC heater that maintains high temperatures during use for precision styling. It heats up quickly to the temperature you've selected for your hair type.

This Instant Heat technology has 5 variable temperature settings. There is a temperature range that's gentle and safe for every type of hair, from the finest to the curliest and most resistant, and helps you create the look you want. Conair's professional salon standards of engineering provide you with a uniform and improved heat recovery system that maintains the iron at constant temperatures. There is a constant surge of power to ensure that heat is continuously and quickly delivered for optimal styling results, unlike other units, which lose

heat during use. This provides consistent styling power so that every strand of your hair is set with the same level of heat and comes out the same way for a perfect finish.

The iron's unique high temperature settings and Instant Heat technology provide styling versatility for all hair types. If you have fine hair, a low temperature will provide the best

results. If you have thick, wavy or hard-to-traighten hair, keep the heat setting on high. You can vary the iron's temperature according

to your particular need by selecting the desired temperature setting.

Temperature Setting Guide

TEMP. CONTROL	HAIR TYPE
Low 266°F Fragile/Fine Hair
Medium 302°F Thin Hair
Med-High 338°F Medium/Normal Hair
High 374°F Wavy/Courly Hair
Maximum 410°F Coarse/Thick Hair

extensions.

1. No unique as panels castes on sale

2. No table is required to be provided by the applicable standards of the Company's 2014 report.

13. No utility unit extension can este

elements to similares.

unfin to other on [on]omnionnion

Plug the iron into an electrical outlet. Press ON/OFF button. The iron will heat up to the default temperature setting (338°F/170°C). Adjust temperature to desired level. Red light will blink until it reaches desired temperature setting and then becomes solid. To turn off, press ON/OFF button (lights will go off). Never leave your flat iron on and unattended. However, should you fail to turn the unit off, it will shut itself off automatically within 60 minutes.

WARNING: The flat iron's Double Ceramic plates will get very hot within a few seconds and should not come into contact with the skin after the flat iron has been turned on.

GET TO KNOW YOUR FLAT IRONS

*As compared to typical straightener plate length of 85mm **As compared to standard Conair ceramic coating

TO STRAIGHTEN HAIR

Hair should be clean and completely dry before using the flat iron. For best results, use a light styling product before blow-drying hair.

1. Start with a hair section that is 112 inches wide and no more than 12 inch thick.

2. Open the iron and place the hair section between the two hot plates, close to the scalp. Trap hair between the plates by firmly squeezing the handles together.

3. While maintaining the tension, slowly pull the unit down along the hair section toward the ends. At the ends, release the pressure on the handle and allow the hair to slide out.

4. Repeat the process on additional sections of hair until you achieve the hairstyle you desire. It may be necessary to repeat the process on certain areas, depending on the texture of your hair.

Some experience is necessary when learning to use this flat iron. After using the iron several times, you will learn the ideal way to straighten and style your hair.

ADD VOLUME AND SHAPE

To add flips and waves, secure ends in between plates and wrap hair around the outer housing. It's an easy way to add shape to straight styles. Turn your wrist up or under to create flips, add curl or more body.

Your flat iron is virtually maintenance free. No lubrication is needed. Keep all vents and openings clear of dirt and dust. If cleaning becomes necessary, disconnect the unit from the power source, allow it to cool and wipe exterior with a cloth. If any abnormal condition occurs, unplug the unit, allow it to cool, and return it for repair to an authorized service representative only. No repairs should be attempted by the consumer.

attempted

CAUTION

NEVER allow the power supply cord to be pulled, twisted, or severely bent. Never wrap the cord tightly around the appliance. Damage will occur at the high flex point of entry into the appliance, causing it to rupture and short circuit. Inspect the cord frequently for damage. Stop use immediately if damage is visible or if unit stops or operates intermittently.

STORAGE

When not in use, your iron is easy to store. Allow appliance to cool, then simply store out of reach of children in a safe, dry location. Do not jerk or strain cord at plug connections. Do not wrap the line cord around the appliance. Allow the cord to hang or lie loose and straight at the point of entry into the appliance.

18P4050961

©2020 Conari Corporation East Windsor, NJ 08520

www.conal.com/registration

Centro de servicio Conar Corporation Service Department 7475 N. Gen Harbor Blvd. Sendale, AZ 85307

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not additional ventilation, accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio, TV technician for help.

SUPPLIER'S DECLARATION OF CONFORMITY

Brand: Conair®

Model No.: CS221CAS/CS221WG/CS221N/CS221CS/CS221ST/CS221SN/CS221UL/CS221STR/CS222CS/CS222ST/CS222STR/CS222SN/CS223CS/CS223N

Description: Flat Iron

Responsible Party: Conair Corporation, 1 Cummings Point Road, Stamford, CT 06902 [phone]

Standards: FCC Part 15 Subpart B, ANSI O63.4-2014

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.

DATE OF ISSUE: 08/21/2019

CONQUI NO SERA RESPONSABLE EN NINGUO CASO, POR NINGUO DANO ESPECIAL, INCIDENTAL O CONSCUENTE DEBIDO AL INCMULTIMENTO DE ESTA O CUALQUER OTRA GARCANTIA, EXPRESA O

1 Cumming's Point Road, Standard, CT 06902

Parte responsible: Conair Corporation,

AVISO DE LA COMISION FEDERAL DE COMUNICACIONES (FCC):

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES

LIMITED THREE-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 36 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return

the defective product to the service center listed on book, together with your purchase

listed on back, together with your purchase receipt and \$7.50 for postage and handling.

California residents need only provide proof of purchase and should call 1-800-2-CONAIR

for purchase and should call 1-000-3-DONAIN for shipping instructions. In the absence of a

purchase receipt, the warranty period shall be 36 months from the date of manufacture.

BE 50 MONTHS FROM THE DATE OF MANUFACTURE. ANY IMPLIED WARRANTIES, OBLIGATIONS,

OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF

LIMITED TO THE IMPI ELED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 26-MONTH DURATION

IN DURATION TO THE 30-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above

long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR

FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH

OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. WHATSOEVER, Sor

EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation

of special, incidental, or consequential damages, as the above limitation may not apply.

ages, to you

This warranty gives you specific legal rights, and you may also have other rights, which

and you may also have vary from state to state.

BEAUTY TIPS:

To achieve the looks you love and for more great Conseir®

for more great conair products, visit www.conair.com

Service Center

Conair Corporation Service Department

7475 N. Glen Harbor Blvd Glendale, AZ 85307

Glenusie, AZ 03307

Please register this product at www.conair.com/registration

www.fooshan.com/Registration

For information on any Conair product, call 1-800-3-CONAIR or visit us on the web at

www.conair.com

©2020 Conair Corporation

East Windsor, NJ 08520

18PA050961

DOUBLE CERAMIC

FLAT IRONS

Instructions & Styling Guide For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

Models CS221/CS222/CS223 - All Versions 1 in. (25 mm) - CS221 1½ in. (38 mm) - CS222 2 in. (51 mm) - CS223