Glendon 53640-01 - Lighting Livex Lighting - Free user manual and instructions

Product Type	Ceiling Mount Lighting Fixture
Brand	Livex Lighting
Model	Glendon 53640-01
Height	Approximately 8 inches (20.3 cm)
Width/Diameter	Approximately 12 inches (30.5 cm)
Weight	Approximately 3 lbs (1.4 kg)
Power Source	Hardwired, 120V AC, 60Hz
Bulb Type	Standard medium base (E26) bulb (not included)
Maximum Wattage	60W (or equivalent LED)
Number of Bulbs	1
Shade Material	Glass
Frame Material	Metal
Finish	Matte Black (typical for this model)
Installation	Hardwired to junction box (not included)
Mounting Type	Ceiling mount
Safety Rating	UL Listed for dry locations
Dimmable	Yes, when used with dimmable bulbs and compatible dimmer
Maintenance	Wipe with a soft, dry cloth; do not use abrasive cleaners
Warranty	1 year limited warranty
Included Parts	Fixture, mounting plate, screws, wire nuts, check ring
Not Included	Junction box, light bulb
Customer Service	800-761-8056, www.livexlighting.com

Frequently Asked Questions - Glendon 53640-01 Livex Lighting

What type of bulb does the Glendon 53640-01 use?

The fixture uses a standard medium base (E26) bulb rated up to 60 watts (or equivalent LED). The bulb is not included.

Is the fixture dimmable?

Yes, when used with dimmable bulbs and a compatible dimmer switch, the fixture supports dimming.

How do I install the Glendon 53640-01?

Turn off power at the circuit breaker. Remove old fixture, attach mounting plate to junction box, connect wires (black to black, white to white, ground to ground), secure canopy, and install glass shade with check ring. See manual for details.

What is the weight of this fixture?

The fixture weighs approximately 3 pounds (1.4 kg).

Can I install this fixture in a bathroom or outdoor area?

The fixture is rated for dry locations only, so it is not suitable for bathrooms, outdoors, or damp areas.

Does the fixture come with a warranty?

Yes, Livex Lighting offers a 1-year limited warranty against manufacturing defects.

What tools are needed for installation?

You will need a screwdriver, wire stripper, electrical tape, and possibly a ladder. A voltage tester is recommended for safety.

How do I clean the fixture?

Use a soft, dry cloth to wipe the glass and metal. Do not use abrasive cleaners or liquids to avoid damage.

What is the height and width of the fixture?

Approximate dimensions: height 8 inches (20.3 cm) and diameter 12 inches (30.5 cm).

Is a junction box included?

No, the junction box is not included. You must use a standard electrical junction box (sold separately).

USER MANUAL Glendon 53640-01 Livex Lighting

ASSEMBLING & INSTALLATION INSTRUCTIONS

The drawing shown may not exactly match the product enclosed. However, the installation instructions do apply to this product.

53640

◆ WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
◆ ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.

ASSEMBLING THE FIXTURE (Fig.1)

1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be care not to lose any small parts necessary for installation.
3. Attach the mounting plate to the Junction Box with the two junction box screws as shown. The side of the mounting plate marked "GND" must face out. The junction box is not included.
4. While holding the lamp body towards the ceiling, connect the electrical wires as Shown in Fig.2, making sure that all wire nuts are secured. You may have to wrap the connections with electrical tape. If your junction box has a ground wire (green or bare copper), connect the lamp body ground wire to it. Otherwise connect lamp body's ground wire directly to the mounting plate with the green screw provided. After wires are connected, tuck them carefully inside the Junction Box.
5. Install the lamp body's canopy onto the junction box, aligning the side screw hole on mounting plate with mounting holes in canopy, lock it securely with the mounting screws.
6. Raise the glass up towards lamp body's lamp holder, using check ring secure until tight it.
7. Install the light bulb(not included) in accordance with the fixture's specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!

Your installation is now complete. Return power to the junction box and test the fixture.

FIG.1

FIXTURE WIRES WHITE

HOUSE WIRES White (Neutral)

HOUSE WIRES Green or Bare Copper(Ground)

Thank you for purchasing a LIVEX product.

Need assistance with parts or assembly? Please call customer service at: 800-761-8056

Or visit us online at: WWW.LIVEXLIGHTING.COM

©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC.

DOC20221053640