SmarterHome KASHWLGRGDA - Garage door opener Kogan - Free user manual and instructions

Product Type	Smart Garage Door Opener
Brand	Kogan
Model	SmarterHome KASHWLGRGDA
Connectivity	Wi-Fi 802.11 b/g/n 2.4 GHz
Control App	Kogan SmarterHome App (iOS & Android)
Smart Home Compatibility	Amazon Alexa, Google Assistant
Motor Type	DC motor with belt drive
Max Door Weight	160 kg (353 lbs)
Max Door Area	12 m² (130 sq ft)
Safety Features	Auto-reverse, obstruction detection, rolling code security
Power Supply	220-240V AC, 50/60 Hz
Standby Power	< 1 W
Light Source	Integrated LED (2 x 10W)
Material	Steel & plastic housing
Dimensions (Motor Unit)	320 x 210 x 180 mm
Weight (Motor Unit)	5.2 kg
Rail Length	2.4 m (can be adjusted for 2-3m ceilings)
Operating Temperature	-20°C to 50°C
Installation Type	Ceiling mounted with rail system
Warranty	2 years
Remote Controls Included	2 x 433 MHz remotes
Battery Backup	Yes, for up to 20 operations

Frequently Asked Questions - SmarterHome KASHWLGRGDA Kogan

How do I connect the Kogan SmarterHome Garage Door Opener to Wi-Fi?

Download the Kogan SmarterHome app, create an account, and follow the in-app pairing instructions. Ensure your phone is connected to a 2.4 GHz Wi-Fi network.

Can this opener work with Alexa or Google Assistant?

Yes, it is compatible with Amazon Alexa and Google Assistant. Enable the Kogan SmarterHome skill in the respective app and link your account.

What is the maximum door weight it can lift?

The opener can handle doors up to 160 kg (353 lbs). For heavier doors, consult a professional installer.

How do I troubleshoot if the door doesn't close fully?

Check the safety sensor alignment. Ensure both sensors face each other without obstruction. Clean the lenses and adjust the brackets if needed.

Does the opener have a battery backup?

Yes, it includes battery backup for up to 20 operations during power outages. The battery recharges automatically when power is restored.

Can I use the original remote controls with this unit?

The unit comes with two 433 MHz remotes. Existing remotes may be programmed if compatible. Refer to the manual for programming instructions.

How do I adjust the travel limits?

Use the limit adjustment screws or the app's calibration feature. Follow the manual to set the open and close positions accurately.

What maintenance is required?

Regularly lubricate the rail and chain/belt (if applicable) with a lithium-based grease. Check the safety sensors and test the auto-reverse monthly.

Does it support geofencing or schedules?

Yes, via the Kogan SmarterHome app, you can set schedules and enable geofencing to auto-close/open the door based on your phone's location.

What is the noise level?

The DC motor and belt drive ensure quiet operation, typically around 45-55 dB, making it suitable for attached garages.

USER MANUAL SmarterHome KASHWLGRGDA Kogan

Pure vertical line pattern with three dots, no text or symbols present

SMARTERHOME™ WIRELESS GARAGE DOOR OPENER

KASHWLGRGDA

OVERVIEW

The Kogan Smart Wireless Garage Door Opener is a companion to your existin. It allows your door opener to be controlled and monitored with a smartphone

Confirm the following before installation:

Simple line drawing of a wireless router (no text or symbols)

2.4GHz, 802.11b/g/n Wi-Fi Route

Technical line drawing of a mechanical component or housing (no text or symbols visible)

A Compatible Garage Door Op

Tools required:

Line drawing of a screwdriver with a pointed tip and handle (no text or symbols)

Illustration of a handheld electric drill bit with screwdriver (no text or symbols)

Line drawing of a ladder structure with four steps, no text or symbols present

Reminder: Please check the compatibility of your door opener before installation.

Components

Wi-Fi Indicator Status

Name	Function	Status
Wi-Fi indicator	Flashing red rapidly.	Wi-Fi is not configured in Smart Mod
	Flashing red slowly.	Wi-Fi is not configured in AP Mode.
	Flashing green.	Wi-Fi is configured but not connected network. Check the router's firewall or Fi SSID and Wi-Fi password.
	Flashing blue.	Door Sensor is not paired with control please open or close the door or fli sensor for 90 degrees to pair.
	Solid green.	Wi-Fi configured, Working Mode.

Button Functions

1. Reset the Device

• If the Wi-Fi indicator doesn't flash red, press and hold the reset button seconds, it will flash red, this means it was reset successfully.
• Resetting will clear the Wi-Fi configuration and door sensor pairing.

2. Switch Wi-Fi configuration mode

If the Wi-Fi indicator flashes red, press and hold the reset button for 3 secor will switch into Wi-Fi configuration mode and the Wi-Fi indicator will flash rapidly according to the mode.

If the Wi-Fi indicator flashes green or stays solid green, press and hold the b seconds, the Wi-Fi indicator will flash blue, and the door sensor is cleared from

Compatibility

Chamberlain or Lift Master	All models with security+ are not compatible.
Craftsman	All models with assurance+ 2.0 are not compo
Genie	Compatible models:Genie Series II openers - best identified by t console button(s), which are a non-black colc covers the vast majority of Genie openers.Incompatible models:Genie Series III openers - best identified by t console button(s), which are black.
Linear	All models are compatible.
Marantec	All models are compatible.
Overhead Door	Compatible models:Series II openers- best identified by the wall button(s), which are a non-black colour.Incompatible models:Series III - best identified by the wall console button(s), which are black.
Stanley	All models are compatible.
Wayne Dalton	All models are compatible.

Checking compatibility by yourself

Take a wire with both ends stripped or a pliers and put each end to the as the wall button wires are terminated to (Terminal #A and Terminal #B, See above). By doing so, if your door activates, then your door opener is compatible device. If the door does not activate, then the opener is not compatible by c

INSTALLATION

Note:

Please power off your garage door opener before installing the device.

1) Connect the cables of the controller to your garage door opener terminals, be connected to the wall button. If you have installed a wall button, please together.

Connect the wire of the controller garage door opener terminal which should be connected to the wall

Install the door sensor

Stick the sensor on the top flap of your garage door, please make sure that the sensor is correct.

Note:

Power on the device and check the controller's Wi-Fi indicator light after installed the door sensor. It should be solid green.

If it flashes in blue, please try to control the door, the controller will automatically.

How to link the door sensor to the controller ifthe door indicator is notcorr

Please set based on the controller's indicator:

- If it is red, please configure the Wi-Fi connection first, then go to the i

- If it flashes in green, please check the Wi-Fi configuration, then go to the

- If it is solid green, press and hold the reset button of the controller for until it flashes blue, then go to the next step.

- If it flashes blue, make sure that you have installed the sensor on the Open the door or close the door and the sensor will be paired with automatically.

Note: The sensor only supports sectional doors, and does not support roller doc

Testing

Power on the device and the garage door opener. Open or close the door ar app. If the door position is not correct after you operate the door four or m something wrong. Please try the following steps to rectify:

1. Press and hold the reset button for 3 seconds until it flashes in red t device.
2. Add the device through the Smarter Home app again, the Wi-Fi indicate flash in blue after you add it successfully.
3. Close or open the door, the Wi-Fi indicator light will be solid green with working now.
4. Operate the door through Smarter Home app for three times again, che position in the app.
5. If the steps above failed, please contact Kogan for help.

APP INSTALLATIOI

Download the "Smarter Home" app from the Play Store (Android) or App Store

Register

If you do not have a "Smarter Home" application's account, register or sign in verification code sent by SMS.

To register:

1. Tap to enter registration page.

2. The system automatically recognises your country/area. You can also select country code manually. Enter your mobile phone number/email address or "Next".

3. If you choose the mobile phone number option, then enter the verification of the message sent to you by SMS. Set a password as prompted and "Confirm" to finish your registration.

Adding the device through network

1. Plug in the device to the socket and power the Kogan Garage Door C on and check that the Wi-Fi indicator is rapidly blinking in red. If not, Wi-Fi button for 3 seconds to reset the device.
2. Open the Smarter Home app and tap "+" in the upper right to add through the network.
3. Ensure the device's Wi-Fi indicator rapidly flashes and tap "Confirm indice rapidly blinking".
4. Select Kogan Garage Door Opener.
5. Connect to Wi-Fi network and return to the "Smarter Home" app.

The device will commence the pairing process and connect to the app.

Note:

The Wi-Fi network must be the 2.4GHz band. 5GHz networks will not

After successfully configuring the devices, the device will be show on the home enter its control page. The device's Wi-Fi indicator light will flash blue.

Note:

• When the device is online it can be controlled.
• When device is offline, it displays "Offline" and cannot be remotely power
• The garage door opener does not support 5GHz networks, ensure your V 2.4GHz.
• If you can't add the device to the app successfully, please contact Kog and don't proceed to the next step.

More functions of the Application

There are two setting options for you to set automated scenes.

1. One option is to add the device to the "condition" list to trigger your devices.
2. Another option is that add the device to the "action" list to be trigger conditions.

Adding the device to the "Condition" list:

< All Devices Living Room Mast Kogan Smart Wireless Garage Door 0... >	< Select Function state >	< state
		Open
		Closed
		opening
		Closing

Note: Only "Open" and "Closed" is valid.

Adding the device to "Action" list:

Note: Only "Open" and "Close" is valid.

GOOGLE HOME

Note:

You will need to have set up a Google Home account prior to linking SmarterHome device.

1. In the "Home Control" screen, select the icon to set up device;
2. Select "set up device" to add new device, then select "works with Good

Set Up New Device

1. A list will appear showing actions and a search function to access more here, install the SmarterHome app.
2. Log into your SmarterHome account with your email address or mobile
3. Once linked, it will show the devices linked to your account: you can rooms. You will be prompted to authorize apps to sync.
4. Click "Done" and then it will give you a list of commands available.
5. When successfully linked, you will see it on your "Home Control" screen bottom of the app screen. You can now control your Kogan SmarterHoi through Google Home.

4:52 Add devices	4:29 Smarter	4:28 Done px1.tuyaus.com
Add new @Nodus Smart #Age of Discovery IoT 1H 1Home for KNX and Loxone Abode Smart Home AC Freedom AC Freedom EU Accentronix Smart Home Adora Home ADT Pulse SmartHome Adurosmart Home Advanceシリーズ 照明スイッチ AEG Home Comfort	Linked Add new Nanoleaf Smarter Series Smarter Home Smarter Kettle and Coffee Vera Smarter Home Control	Account +01 Phone Hunter/Engine Address Password Type your password here Link Now Forgot Password SMS message
Add Device	Select Device	Login to App

Voicecommand

If the voice command above doesn't work, please try "Ok Google, turn on (---) Google, turn off (---)".

Note:

“---” is the device name. It is suggested that you rename the device but uncommon name.

ALEXA

Note: You will need to have set up an Alexa account prior to linking your K SmarterHome device.

1. Select "Menu" and then "Skills".
2. Search for the app and enable it.
3. Log into your SmarterHome account with your email address or mobile
4. Select "Discover Devices" and the app will begin searching.
5. When successfully linked, you will see a list of connected Kogan Smarte devices. You can now control your Kogan SmarterHome devices through your voice. Use the voice commands:

“---” is the device name. It is suggested that you rename the de but uncommon name.

Alexa Account Setup

Search App in All Sk

Enable App

Need more information?

This is a Quick Start Guide and while we hope that this has given you needed for a simple set-up, a full user guide outlining all of this product's features can be found online at help.kogan.com

kogan