SKS-M2J-Y - Light signaling PATLITE - Free user manual and instructions
Find the device manual for free SKS-M2J-Y PATLITE in PDF.
| Product Type | Rotating Beacon (Light Signaling) |
| Brand | PATLITE |
| Model | SKS-M2J-Y |
| Color | Yellow |
| Rated Voltage | 100 - 240 V AC (50/60 Hz) |
| Wiring Type | Cable type (J) |
| Buzzer | None |
| Mounting | 3-screw mounting using bolts |
| Accessories Included | Mounting bracket, waterproof sheet, M4 nut & plain washer (3 sets) |
| Conformity Standards | CE (EMC, RoHS), FCC Part 15 Class A, UL/cUL |
| Protection Rating | Not specified (avoid water on buzzer opening if applicable) |
| Maintenance | Clean with soft cloth and water; do not use solvents, gasoline, or oil |
| Safety Precautions | Disconnect power before wiring; use a fuse; do not disassemble; avoid short circuits |
| Spare Parts & Repairs | Available via PATLITE website (https://www.patlite.com) |
| Wire Gauge Recommended | Solid: 0.13-1.5 mm² (AWG28-14); Stranded: same |
| Fuse Rating | 250V 1A |
Frequently Asked Questions - SKS-M2J-Y PATLITE
User questions about SKS-M2J-Y PATLITE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Light signaling in PDF format for free! Find your manual SKS-M2J-Y - PATLITE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SKS-M2J-Y by PATLITE.
USER MANUAL SKS-M2J-Y PATLITE
Multi-function Beacons
TYPE SF08 / SF10
Flashing Beacons
TYPE SL08 / SL10 / SL15
Notice to Customer
Thank you very much for purchasing our Patlite products.
- Request the installation and wiring be performed by a professional contractor if construction work is involved.
- Prior to installation, read this manual thoroughly before using this
product to ensure correct use. • In addition, please store this manual for future reference when
performing maintenance, repairs or inspections
- For options and repair parts, please visit our website (https://www.natlite.com)
(https://www.patite.com). - If there are any questions concerning this product, refer to the contact
information at the end of this document and contact your nearest BATUTE Sales Representative
PATLITE Sales Representative.
1 Read this First (Safety Precautions)
Warning Failure to observe the following may result in
A warning death or serious injury.
- To prevent from short-circuits or damage, observe the following: Be sure the power is disconnected before replacement or repair
- Be sure the power is disconnected before replacement of repair, including the replacement of the fuse.
- Use this product in a properly maintained condition. (Replace or repair if the globe, case, etc. are damaged.)
- If installing this product requires construction work, ask a specialist in order to
avoid fire, or personal injury. - When this product is used for security purposes, it should be inspected daily.
- When this product is used for security purposes, it should be inspected daily. In case a malfunction should occur, it is recommended that you use this
product together with other security products. ● After installation, do not use this product to climb up onto the equipment with
- After installation, do not use this product to climb up onto the equipment with. Failure to comply will result in product damage and/or falling off the machinery
- 2.1.1.1 Failure to comply with the following points may
Caution Failure to comply with the following points may result in injury, physical loss or damage.
- Be sure to put a fuse in the wiring circuit between the power source and
- Use is put a fuse in the wiring circuit lines in the power secured and equipment for protection. If a fuse is not added, it may result in product and/or equipment.
- equipment failure. - Be sure to prevent electrostatic damage due to discharge when working with
this product for wiring, exchanging units, setting up parameters, etc. by
discharging static electricity on your body, etc.
- Do not disassemble of detach during operation
2 Model Number Configuration
■ SF·SL Models
RT 2-point Hole Type Mounting • Terminal block 3-point Hole Type Mounting • Terminal block (SL15 only)
• KT only(SL15 : No Buzzer)
Model Number Example: SE08 M1KTR P
- ∅80 - 12 - 24 V DC - 2-point hole type mounting • Terminal block
■ SK Model
Model Number Example
SKH-M1JB-R
- ∅100 - 12 - 24 V DC - Cabtyre Cable - With buzze - Red color
-5--7--8--6.
3 Part Names
■ Cable type J
■ Terminal ble
Accessory List
| NameModel | QTY | |
| SF□□-□□KT/SL□□-□□KT | Mounting Bracket, Waterproof Sheet | 1 |
| SF08-□□J/SL08-□□J/SKS Model | M4 Nut, Plain Washer | 3 |
| SF10-□□J/SL10-□□J/SKH Model | M5 Nut, Plain Washer | 3 |
| SL15-□□J/SKP Model | M8 Nut, Plain Washer | 3 |
4 Installation
Notice • Ensure that the product is installed in an environment that meets the following
Notice: Ensure that the product is installed in an environment that meets the following conditions:
- Where excessive vibration is not present
- On a sturdy surface - On a level surface
- When it is necessary to waterproof the backside of the installation surface;
- Provide a sealant coating around the nuts of the backside of the installation
surface.
- Waterproof the cable mounting area. • Ensure that the product is mounted upon
- Ensure that the product is mounted upright when installed outdoors. - Ensure that the speaker is facing forward when installing the buzzer.
- Depending on your operating environment, additional waterproofing may be
required on the Terminal Block openings for SKH-M☐T models
■ 3-Screw Mounting Type J T
(1) Insert the bolts of the beacon into
the holes of the mounting surface
(2) Use the nuts and washer
(accessory) to secure in place.
Installation Example
Maximum Board Thickness of Mounti
Installation Dimensions
Refer to the "Installation Manual"
■ 2-point Hole Type Mounting (SF • SL Models)
3-point Hole Type Mounting (SL15 Model Only)
(1) Use the screws or bolts, nuts. to secure the mounting bracket
(accessory) to the mounting surface. (Installation screw and nut are not included with this product
(installation screws and nuts are not included with this product. Binding head screws or pan head screws are recommended.)
| Model | Screw Hole Depth of Mounting Bracket | Nominal Diameter |
| SF08/SL08 | 4.4 mm | M4 |
| SF10/SL10 | 5.7 mm | M5 |
| SL15 | 4.8 mm | M8 |
(2) Check that the O-ring is not twisted.
(3) Align the main unit of product with the positioning Indicator and
turn it clockwise to lock it.
Installation Example
2-point Hole Type Mounting 3-point Hole Type Mounting
Installation Dimensions
Refer to the "Installation Manual"
▲ Cautious
Caution Use a soft cloth moistened with water to clean the globe or case. (Do not use thinner, benzine, gasoline or oil.)
1.2007 (2-NOF-2008 Limiter, 2009), 2008 (2-NOF-2009 Limiter)
Note The type with a buzzer, if the buzzer opening is splashed
with water, the Sound Pressure Level may drop.
5 Wiring
Caution • Make sure the power is OFF before wiring. A short circuit
■ Cation may damage internal circuits.
- Ensure the proper working voltage is used. Any mistake in wiring may result in damage
- Do not pull the wire, or stuff it inside of this case.
- Be sure the wiring is done properly. Any mistake in wiring may result in damage
- In the M2 model, do not perform blinking control by turning the power supply ON/OFF. Any mistake in wiring may result in damage.
- Do not apply a voltage to the common wire. (M1 type)
Do not apply a voltage to any wire other than the power supply wire. (M2 type) Failure to comply will result in product damage (except buzzers wire of SKH M1).
- Failure to comply will result in product damage.(except buzzer wire of SKH-MT) - Do not expose the wiring from the device. If tension is applied to the wiring, the
wiring may be disconnected, resulting in a short circuit or an electric shock.
- Use either a Contact Switch or Contact Relay for External Contact that power supply wire of SE, SL, SK Models and buzzer wire of SK Model. Failure comply
supply wire of SR, SE, OR Models and buzzer wire of OR Model. Failure comply may result in fire, product malfunction.
Notice • The protection rating does not include the Cabtyre Cable
Ends. If the ends of the lines in contact with water are exposed to dry water
If the ends of the it are in contact with water or exposed to dew or condensation, refer to the indications below to dress the wire ends for water
resistance.
- Connect the it ends in a location which will not expose the ends to water.
[External contact capacity of power supply wire]
M1 M2
Current Capacity (Is) 3A or more 1A or more
[ External contact capacity of signal wire and buzzer wire ]
SE • SI Models
| M1 | M2 | |
| Current Capacity (Is) | 10 mA or more | 10 mA or more |
| Withstand Voltage (Vs) | 20 V or more | 20 V or more |
| Leakage Current • (IL) | 0.1 mA or less | 0.1 mA or less |
- When using an NPN open-collector transistor
SK Model
M1 M2
| Current Capacity (Is) | 0.5 A or more | 0.5 A or more |
| Withstand Voltage (Vs) | 35 V or more | 20 V or more |
[ Fuse ]
Fuse Rating 250 V 1 A
Wire Type / Wire Gauge
Wire Type : UL2464
Wire Gauge : M1 AWG22
。
M2 Power Supply Wire
Excluding Power Supply Wire AWG24
Wiring Example
Refer to the "Installation Manual"
Terminal Block Wiring
■ Recommended lead wire specifications
Wire Type Wire Gauge (Solid Wire) Wire Gauge (Stranded Wire)
Wire Type Wire Gauge (Solid Wire) Wire Gauge (Stranded Wire) UL 1007 (UL 1430) 0.12 x 1.5 mm² AWC28 - 14
OL1007 / OL1430 0.13 \~ 1.5 mm AWG28 \~ 14
• Temperature rating should be above 75°C, and the conductor material should be of consensus.
de of co
Note
Strip 8-9 mm of wire insulation from the lead wire to insert into the terminal block.
Do not tug on to the lead wire to remove- always unlock the lever before removing the wire.
removing the wires. The tip of the flatbez
The tip of the flathead screwdriver should be no more than 2mm wide and 0.5 mm thick
Do not put excessive force on the lever, as this may cause the lever to break.
- Installation
■Removal
to the groove of
ase the lock.
2 The stripped side of the lead wire is inserted in
the slot And lock
the store, and look
1
[Non-Text]
2 Pull out the lead wire.
-
6 Specifications
• EMC Directive (EN61000-6-4, EN61000-6-2)
• ROHS Directive (EN5058) • UI 508 CSA-C22 2 No 14
• FCC Part 15 Subpart B Class A
7.2.1.1
This product conforms to EN standards and shows the CE Marking. This product has been tested and found to comply with the limits for a Class A
This product has been tested and found to comply with the limits for a class IV device, pursuant to EMC DIRECTIVE. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This product must not be used in residential areas.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications
Operation of this equipment in aresidential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
(Note) • Dimensions and specifications may change without notice due to
continual product improvement
- PATLITE and the PATLITE logo is a trademark, or registered trademark of the PATLITE Corporation of Japan and each country.
the PATELE Corporation of Japan and each country.
(Importer for EU)
PATLITE Europe GmbH Am Soeldnermoos 8, D-85399 Hallbergmoos, Germany
- Notice to Customer
- Read this First (Safety Precautions)
- Warning Failure to observe the following may result in
- - 2.1.1.1 Failure to comply with the following points may
- Caution Failure to comply with the following points may result in injury, physical loss or damage.
- Model Number Configuration
- ■ SF·SL Models
- • KT only(SL15 : No Buzzer)
- ■ SK Model
- Model Number Example
- Part Names
- ■ Cable type J
- ■ Terminal ble
- Accessory List
- Installation
- Notice • Ensure that the product is installed in an environment that meets the following
- ■ 3-Screw Mounting Type J T
- Insert the bolts of the beacon into
- Installation Example
- Maximum Board Thickness of Mounti
- Installation Dimensions
- ■ 2-point Hole Type Mounting (SF • SL Models)
- 3-point Hole Type Mounting (SL15 Model Only)
- Wiring
- M1 M2
- SE • SI Models
- SK Model
- [ Fuse ]
- Wire Type / Wire Gauge
- Wiring Example
- Terminal Block Wiring
- Specifications
Brand : PATLITE
Model : SKS-M2J-Y
Category : Light signaling