LSP-R1000P - Wireless camera LG - Free user manual and instructions

Product Type	Wireless Color Camera with Video Monitor
Model	LSP-R1000P
Display	2.5-inch TFT LCD, 862 x 228 dots
Camera Resolution	360 horizontal TV lines
Wireless Frequency	2.4 - 2.48 GHz
Range (with obstacles)	Up to 30 m (100 ft)
Range (without obstacles)	Up to 75 m (246 ft)
Camera Dimensions (W x H x D)	82 x 139 x 65 mm
Camera Weight (without batteries)	182 g
Monitor Dimensions (W x H x D)	87 x 115 x 65 mm
Monitor Weight (without batteries)	200 g
Camera Power Input	5V DC, 430 mA
Monitor Power Input	9V DC, 800 mA
Battery Options	4x AA batteries (camera and monitor) or rechargeable battery pack (LSP-R1001 only)
Motion Detection	PIR sensor with visual and audible alert
Night Vision	Infrared lamp for low-light operation
Audio	Built-in microphone (camera) and speaker (monitor)
Operating Modes	Power Save, Auto (cyclic), Manual (select camera)
Adjustable Settings	Brightness, Color, Contrast, Alarm volume, Speaker volume
Multi-Camera Support	Up to 3 cameras (additional cameras sold separately)
Channel Selection	3 channels via DIP switches (2.41, 2.44, 2.47 GHz)
Accessories Included	Camera, Monitor, AV cable, power adapters, rechargeable battery pack (LSP-R1001 only)
Cleaning	Clean with dry cloth only; unplug before cleaning
Safety Precautions	Do not expose to water, rain, or direct sunlight; avoid heat sources; use only specified attachments

Frequently Asked Questions - LSP-R1000P LG

How do I set up the LG LSP-R1000P wireless camera system?

Place the camera on a horizontal surface, connect the power adapter to the camera and a mains outlet, then turn it on. For the monitor, plug in the power adapter and turn it on. The system will enter Auto mode automatically.

What is the maximum range between camera and monitor?

The communication range is up to 100 feet (30 meters) indoors with typical obstacles like walls. Without obstacles, the range increases to 50-75 meters (164-246 feet).

Can I use multiple cameras with one monitor?

Yes, the system supports up to three cameras. Each camera and the monitor must have DIP switches set to the same channel (1, 2, or 3). Additional cameras must be purchased separately.

How do I charge the rechargeable battery pack?

Connect the rechargeable battery pack to the camera or monitor, then plug in the supplied power adapter. Charging time is approximately 16 hours for the camera pack and 25 hours for the monitor pack. Use only the supplied adapter.

What should I do if I get interference on the camera picture?

Ensure the camera and monitor are within range with no large obstructions. Reposition the units away from other 2.4 GHz devices like microwave ovens or wireless phones. Changing the channel via DIP switches may also help.

How does the motion detection work?

The camera has a PIR motion sensor. When motion is detected, the red light on the camera flashes and an alarm beep sounds on the monitor. In Power Save mode, the monitor automatically turns on from standby when motion is detected.

Can I adjust the picture quality?

Yes. Press the MENU button on the monitor to cycle through Brightness, Blue Color, Red Color, and Contrast adjustments. Use the ▲/▼ buttons to change the level.

What type of batteries does the system use?

Both the camera and monitor can use 4x AA batteries (not included). Alternatively, the LSP-R1001 model includes rechargeable battery packs. Do not mix old and new batteries or different battery types.

How do I switch between operating modes?

Press the P/S button for Power Save mode (standby, scan). Press AUTO for automatic cycling through cameras. Press MANUAL to manually select a specific camera. The dwell time in Auto mode can be adjusted by pressing AUTO and MANUAL simultaneously.

What should I avoid when installing the camera?

Avoid pointing the camera directly at bright light or sunlight, as it may damage the sensor. Also avoid areas with extreme contrast (half bright, half dark). Do not install near water or in humid environments.

USER MANUAL LSP-R1000P LG

The LSP-R1000/LSP-R1001 is a combined wireless colour camera & video monitor (receiver). The high-resolution colour video camera includes a built-in motion detector and microphone, an ideal combination for watching a baby, monitoring a porch, pet, yard or pool. It is also suited to many small business applications.

Features

• 2.4 GHz wireless technology. • 2.5-inch LCD display for good picture quality. - Plug and play installation - LCD display operates in 3 modes: Power save, Auto and Manual. - Adjustable cycle time between cameras in Auto mode. • The Brightness, Colour, Contrast, Alarm volume and Audio volume can be adjusted. - PIR sensor function.

Package Contents

Your package contains the following:

Wireless LCD Monitor.

Wireless Motion Sensor Camera.

9V DC Power Adapter (2EA)

AA type rechargeable battery pack for wireless LCD Monitor. (Supply with LSP-R1001 only)

Recharging Time

Approx. 25 hours. Using Time :

Approx. 2 hours 30

minutes.

AAA type recharge-

able battery pack for

wireless camera (supplied with

LSP-R1001 only)

- Recharging time:

Approx. 16 hours

- Using time:

Approx. 3 hours 30 minutes

AV cable.

Before installation

• The camera must not face into direct sunlight or any bright light, as this may cause damage to the camera.
• Avoid viewing areas where half of the area is in bright light and the other half is in darkness. All types of cameras have difficulty viewing wide variations in light levels.
• The communication range of this device is up to 100 feet (30 m) from the Wireless System Controller in a typical home, depending on the number of obstacles. These can include metal framing, thick walls, and other wireless devices operating at 2.4 GHz. It is recommended that different positions are tried.
• The 2.4 GHz video signals pass easily through home interior walls, but the signal may be reflected by power cables or plumbing inside the wall. The most common source of interference is microwave ovens. Try to avoid mounting the LCD monitor near a microwave oven or other source of RF interference such as a wireless phone.

Part names and functions

LCD monitor overview

[1] LCD monitor screen. Displays live images from the selected wireless camera. [2] Channel indicator. Lights green or red when the channel is selected. Blinks when motion is detected. [3] Mode select buttons.

- P/S: Select when you require the system to enter P/S mode. - AUTO: Select when you require the system to enter auto mode.

- MANUAL: Select when you require the system to enter

manual mode

[4] Speaker

To listen to the sound output from the wireless camera.

[5] Power button.

To turn the LCD monitor On or Off.

[6] Speaker volume adjustment buttons

Adjust the speaker volume level by using the volume

buttons.

[7] Alarm volume adjustment control

Adjust the alarm volume on the LCD monitor by rotating the

alarm volume control.

[8] MENU button

To select the Brightness, Colour or Contrast setting mode.

[9] ▲/▼ button

Adjusts the level of the Brightness, Colour or Contrast.

[10] Audio/Video output jack

Allows connection of another display and/or sound device

using the AV cable supplied

[11] 9V DC Power input jack.

[12] Battery cover case.

The LCD monitor can be operated without the power supply adapter using four AA type batteries or battery pack (Supplied with LSP-R1001 only).

Camera Overview

[1] Camera lens. [2] IR(Infra Red) lamp sensor [3] Motion sensor [4] Microphone The microphone is incorporated into the camera. [5] Infra Red Ir [6] Battery cover once The camera can be operated without the power supply adapter using four AA type batteries or battery pack (Supplied with LSP-R1001 only). [7] 9V DC Power input jack.

Installing the wireless camera

Installing your camera is a simple process. It can be placed on any horizontal surface.

1. Locate the camera on a horizontal surface.

1. Plug the power supply into the camera and the mains outlet.

1. Make adjustments to the camera viewing angle by tilting and panning the camera head with your hand.

1. Press the POWER button to turn the camera on.

Note:

Ensure the power adapter cord is long enough to reach your mounting location.

Installing the LCD Monitor

Installing your LCD Monitor is a simple process. You can either hang the LCD Monitor from the ceiling or place it on a level surface.

1. Place the LCD Monitor on a horizontal surface.

1. Plug the power supply into the LCD Monitor and a mains outlet.

1. Turn the LCD Monitor on

The LCD Monitor system will be activated and enters auto mode automatically.

Note:

Ensure the power adapter cord is long enough to reach your mounting location.

Operating the Wireless Camera System

Mode operation

• P/S (Power Save) mode:

Press the P/S button on the LCD monitor, the system will enter P/S mode. The LCD monitor screen will go blank and enter standby mode while the system continuously scans the active camera(s). If a camera detects motion, the LCD monitor will display the camera picture and a beep will sound. Two minutes after the last motion is detected, the screen returns to standby mode while the LCD monitor resumes scanning.

Press the MANUAL or AUTO button to cancel this mode.

- AUTO mode:

Press the AUTO button on the LCD monitor, and the system will enter auto mode. The system automatically rotates through all cameras. When a camera detects motion, the LCD monitor will display the picture from that camera for a few seconds and a beep will sound. To avoid searching channels that do not have cameras/transmitters assigned, set the dip switches for those corresponding channels to the off position. The dwell time (time taken to switch between cameras) is preset to 4 seconds and can be adjusted from 2 to 30 seconds. To adjust the dwell time, press both the AUTO and MANUAL buttons simultaneously.

Each flash of the LED increases the dwell time by one second. This function will be activated when more than one camera is used.

- MANUAL mode:

Press the MANUAL button on the LCD monitor to select a specific camera. The LCD monitor will switch to a different camera each time the MANUAL button is pressed. When a camera detects motion, the LCD monitor will display the picture from that camera for a few seconds, and a beep will sound. To avoid searching channels that do not have cameras assigned, set the dip switches for those corresponding channels to the OFF position.

Menu Operation

• Brightness adjustment

1. Press the MENU button on the LCD Monitor repeatedly until the LED in the button turns red, indicating selection of the brightness adjustment mode.
2. Adjust brightness level using the ▲/▼ buttons

• Blue colour adjustment

1. Press the MENU button on the LCD Monitor repeatedly until the LED in the button quickly flashes red, indicating selection of the blue colour adjustment mode.
2. Adjust the blue colour level using the ▲/▼ buttons.

• Red colour adjustment

1. Press the MENU button on the LCD Monitor repeatedly until the LED in the button slowly flashes red indicating selection of the red colour adjustment mode.
2. Adjust the red colour level using the ▲/▼ buttons.

• Contrast adjustment

1. Press the MENU button on the LCD Monitor repeatedly until the LED in the button turns off indicating selection of the contrast adjustment mode.
2. Adjust the contrast level using the ▲/▼ buttons.

Note:

On pressing the MENU button, the LED changes as shown below. Turns red ⇔ Turns red on slow flicker ⇔ Turns red on fast flicker ⇔ Turns off ⇔ Turns red.

Motion-Sensing Cameras

The camera is equipped with a PIR motion sensor. When the camera detects motion, a red light flashes on the camera and an alert sounds on the LCD monitor.

Battery installation guide

The Wireless camera system can be used without the supplied adapter.

- LSP-R1000: Remove the battery compartment cover on the camera and LCD monitor, and insert four AA size batteries ensuring the (a) and (-) are aligned correctly as shown below.

- LSP-R1001 : Connect the cable of the rechargeable battery pack to the terminal of the camera and the LCD monitor as shown below.

Rear of the LCD monitor.

< LSP-R1001 >

< LSP-R1001 >

Notes:

• Do not mix old and new batteries and never mix different types of batteries such as standard, alkaline, rechargeable etc.
• Charging the battery when the battery is not completely drained can reduce the battery capacity. The battery must be fully charged only when it is completely drained.
• You must use the supplied adapter to recharge the battery. Using another adapter may caused damage to the rechargeable battery. • The rechargeable battery is a consumable item.

Multi-camera Operation

We recommend the use of only one camera with the LCD monitor. If more than one camera is to be used, the Dip-switch must be set for each camera and the LCD monitor. The LCD monitor system is designed to work with up to three cameras. Additional cameras must be purchased separately.

• Dip-switch position on the LCD monitor

The dip-switch can be found inside the battery compartment as shown below.

Set the viewer to Channel 1. (Default setting) Set the viewer to Channel 2. Set the viewer to Channel 3.

• Dip-switch position of Wireless Camera

The dip-switch can be found inside the battery compartment as shown below.

Set the camera as channel 1 (2.41GHz) (Default setting). Set the camera as channel 2 (2.44GHz). Set the camera as channel 3 (2.47GHz).

Notes:

• If more than one camera is used, interference may occur between wireless devices. If this is the case, the problem can be solved by changing the channel of the camera or changing the frequency band of the wireless devices.
• The wireless home viewer system uses a 2.4GHz frequency band. If this unit is used in close proximity to a microwave oven or a wireless device such as a wireless home theatre system, wireless LAN, wireless telephone, etc., interference may occur. Do not use the wireless home viewer system near any other wireless devices.

Troubleshooting

If any problems occur, refer to the following guide before contacting a service engineer.

Symptom	Correction
Abnormal or no picture	• Check all connections.
	• Ensure the plug on the power cord is securely inserted into the mains outlet.
	• Ensure the camera(s) and LCD monitor are switched on.
	• Ensure the rechargeable battery is fully charged.
Interference on Camera picture	• Ensure the batteries are correctly inserted with (+) and (-) aligned correctly.
	• Ensure each camera is within the range, and no large obstructions are blocking the signal.
	• Try repositioning the camera, the monitor or both to improve reception quality.
	• Reposition other equipment which is in close proximity and may be transmitting at 2.4GHz frequency.
Audio problems	• Ensure the volume is set at a sufficiently high level on the monitor.
	• Ensure the microphone is within range of the sound source.
	• If the unit emits a loud wailing sound (feed-back), try moving the camera away from the monitor or angle the monitor differently.

Specifications

Wireless Camera

Item Description
Rated Voltage 9 V DC
Rated Current	400 mA
Frequency Range 2.4~2.48 GHz
Frequency 2.41, 2.44, 2.47 GHz
Modulation Method FM
Oscillation Method PLL
Image Sensor 1/3" CMOS I:C
Integrated Lens 5.6mm (F)	F:8 Fixed Focus
TV System NTSC/PAL (Colour) Standard
Auto Electronic Exposure	1/60~1/15000 sec.
Min Illumination 0.5 Lux
Resolution 360 Horizontal TV lines
Signal/Noise Ratio 480
Overall Size 82mm (W) x 120mm (H) x 65mm (D)
Weight 182g (Without Batteries)
Operating Temperature 0°C to +45°C
Operating Humidity Less than 65%
Transmitting and Receiving distance	25-30m (with obstacle)50-70m (with obstacle)

Antenna

Item Description
Frequency Range	2.4~2.48 GHz
Polarization	Monopole
SWR	2 : 1
Gain	2 dB
Impedance	50 Ohm
Outline Size	φ 3.5 x 85mm (Transmitter)

LCD Monitor

Item Description
Rated Voltage	9 V DC
Rated Current	800 mA
Frequency Range	2.4–2.48 GHz
Frequency	2.41, 2.44, 2.47 GHz
Intermediate Frequency	480/MHz
Radio Waves Type	Analog
Display Mode	TMR
Display Size (Diagonal)	2.5 inch (LSP-R1000)
Number of Dots(HxV)	882x228 Dot
Dot Pitch (H x V)	0.056 x 0.168 mm
Colour Number	Full Colour/16 Million
Brightness	250cd/m2
Contrast Rate	200:1
Light Source Type LED
TV System	NTSC/PAL (Colour) Standard
Colour Configuration	R.G.B Strip
Overall Size	87mm (W) x 150mm (H) x 65mm (D)
Weight	260g (without Batteries)
Operating Temperature	0°C to +45°C
Operating Humidity	Less than 85%
Transmitting andReceiving distance	25-30m (with obstacle)
	50-70m (without obstacle)

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Regulatory Notices For U.S.A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit. Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture. Caution: This installation should be made by a qualified service person and should conform to all local codes. Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities

appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance

please contact your city office, waste disposal service, or the shop where you purchased the product.

LG WIRELESS HOME VIEWER

Instruction Manual

Models: LSP-R1000

LSP-R1001

Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.

Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.

Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.

P/NO: MFL30580144 (English)

Important Safety Instructions

1. Read these instructions.
2. All these safety and operating instructions should be read before the product is operated.
3. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
4. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
5. Follow all instructions. - All operating and use instructions should be followed.
6. Do not use this apparatus near water. - For example: near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc.
7. Clean only with dry cloth.
8. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
9. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. - Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer's instructions have been adhered to.
10. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
11. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
12. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
13. Only use attachments/accessories specified by the manufacturer.
14. Use only the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
15. Unplug this apparatus during lightning storms or when unused for long periods of time.
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.