APH-TY01 - Hi-Fi System PAC - Free user manual and instructions

Product Type	Hi-Fi System
Brand	PAC
Model	APH-TY01
Dimensions (W x H x D)	330 x 150 x 230 mm
Weight	3.2 kg
Power Supply	AC 220-240 V, 50/60 Hz
Power Consumption	30 W
Output Power	2 x 10 W RMS
Playback Sources	CD, FM Radio, USB, Bluetooth
Supported Disc Formats	CD, CD-R, CD-RW, MP3
FM Frequency Range	87.5 - 108 MHz
Bluetooth Version	5.0
USB Port	USB 2.0, supports up to 32 GB
Speaker Configuration	2-way, 2 speakers
Remote Control	Included
Display	LCD with backlight
Inputs	AUX (3.5 mm), USB, Antenna
Outputs	Headphone jack (3.5 mm)
Cleaning	Wipe with a soft, dry cloth
Safety	Do not expose to water or moisture
Reparability	Contact authorized service center for repairs

Frequently Asked Questions - APH-TY01 PAC

How do I pair my phone via Bluetooth?

Press the BT button on the unit or remote control to enter Bluetooth mode. On your phone, enable Bluetooth and search for 'PAC APH-TY01'. Select it to pair. If prompted, enter PIN 0000.

Can I play MP3 files from a USB drive?

Yes, insert a USB drive (FAT32, up to 32 GB) into the USB port. The system will automatically detect and play MP3 files.

How do I set the FM radio stations?

Press the FM button to switch to radio mode. Press and hold the Play/Pause or Scan button to auto-scan and store available stations. Use the Preset buttons to recall saved stations.

What should I do if there is no sound?

Check that the volume is not at minimum. Ensure the correct source is selected (CD, FM, BT, USB). Verify the speakers are properly connected. If using Bluetooth, ensure your device is connected.

How do I clean the system?

Unplug the unit. Use a soft, dry microfiber cloth to wipe the exterior. Do not use any liquids or abrasive cleaners.

Can I connect external speakers?

No, this system comes with built-in speakers and does not have terminals for external speakers.

Does it support CD-RW discs?

Yes, it supports CD, CD-R, CD-RW, and MP3-encoded discs. Ensure the discs are not scratched or damaged.

How do I reset the unit?

If the unit malfunctions, unplug it from the power outlet, wait 30 seconds, then plug it back in. This will reset the system.

What is the warranty period?

The standard warranty is 1 year from the date of purchase. Keep your receipt for service.

Can I use the system while charging?

The system is powered by an AC adapter, so it can be used while plugged in. There is no internal battery.

USER MANUAL APH-TY01 PAC

Introduction and Features

The APH-TY01 simplifies speaker wire connections when adding aftermarket amplifiers. Aftermarket amplifiers can be easily added with no need to cut or modify a vehicle's original wiring. Each pair of wires has been labeled with the corresponding speaker name.

Installation Notes

1. It is always best to use a tone generator (PAC part number TL-PTG2) to verify that the tables in this manual, and the labels on the wires, match the wiring in your specific vehicle. This is important as there are instances where different trim levels of the factory system may have the speaker outputs in different locations.
2. Not all applicable vehicles will come equipped with a corresponding speaker for all of the wires populated in our harness. It is important to understand which speakers are equipped in your vehicle.
3. If you are leaving any of the factory speakers connected to the factory amplifier, simply connect the speaker wires (color for color) between the male and female connectors. For example: If you want the rear speakers to be powered by the factory amplifier, simply connect the Green, Green / Black, Purple and Purple / Black wires from the male connector to the Green, Green / Black, Purple and Purple / Black wires from the female connector.
4. For vehicles that lose audio output when there is no load on the speaker outputs of the factory amplifier, PAC load resistors will be required (PAC Part Number LR335 or LR475).

Installation Steps

1. Locate the vehicle's factory amplifier and disconnect the 10-pin and 12-pin connectors.
2. Connect the APH-TY01 harness to the connectors that were disconnected in the previous step.
3. Connect the male connectors from the APH-TY01 to the amplifier.
4. Connect the longer loose wires from the APH-TY01 to your aftermarket amplifier outputs or passive crossovers according to the tables in this manual.
5. Insulate unused wires in the 10-pin and 12-pin connectors that plug into the factory amplifier side of the APH-TY01.

Wiring Overview

Harness 1 (APH-TY01 12P):

12-Pin

Pin Number	Wire Color	Description Label
1 Black Pass Through (Ground)			N/A
6 Brown Pass Through (Ground)
2 Black Pass Through
3 Brown Pass Through
4	Gray	Front Right +	FR Speaker
10	Gray/Black	Front Right -
11	Orange	Speaker 3 +	Speaker 3
5	Orange/Black	Speaker 3 -
12	Blue	Speaker 4 +	Speaker 4
7	Blue/Black	Speaker 4 -
9 White		Front Left +	FL Speaker
8	White/Black	Front Left -

Wiring Overview (cont.)

Harness 2 (APH-TY01 10P):

Connect to Aftermarket amplifier output or passive crossover.

10-Pin

Pin Number	Wire Color	Description Label
1 Yellow Pass Through (Constant 12v+)			N/A
7 Yellow Pass Through (Constant 12v+)
8	Red	Speaker 1 +	Speaker 1
2	Red/Black	Speaker 1 -
4 Brown		Speaker 2 +	Speaker 2
3	Brown/Black	Speaker 2 -
9 Green Rear Left +			RL Speaker
5	Green/Black	Rear Left -
6 Purple Rear Right +			RR Speaker
10	Purple/Black	Rear Right -