19093 - Wristwatch Stauer - Free user manual and instructions

Product Type	Hybrid Analog-Digital Watch
Brand	Stauer
Model	19093
Display Type	Analog dial (hour, minute, seconds) + Digital LCD
Main Functions	Time, Date, Day, Month, Alarm, Chime, Stopwatch, Split Timer, Backlight
Time Format	12/24 hour selectable
Stopwatch Capacity	23 hours, 59 minutes, 59 seconds
Alarm Duration	20 seconds (auto-stop) or manual stop
Backlight	Indiglo (E.L.) backlight for LCD
Crown Positions	Position 0 (normal) and Position 1 (time setting)
Band Adjustment	Removable links via pins; requires pointed tool and needle-nose pliers
Power Source	1x button cell battery (not included)
Battery Life	Typical 1-2 years (depends on usage)
Water Resistance	Not specified; avoid exposure to water
Care Instructions	Keep away from moisture, clean with soft dry cloth, avoid shocks
Repair	Professional service recommended for battery replacement and band adjustment

Frequently Asked Questions - 19093 Stauer

How do I set the time on my Stauer 19093 watch?

Pull the crown out to position 1 (see diagram part C). Rotate it clockwise to set the analog hands to the desired time. Push the crown back to position 0 to finish.

How do I set the digital display (date, month, etc.)?

Press the G button three times to enter setting mode. The seconds will flash. Press B to cycle through minutes, hours, date, month, and weekday. Use A to adjust each. Press G to return to normal time.

How do I set the alarm?

Press and hold B to show alarm time. Press G twice to make the hour flash, then adjust with A. Press B to switch to minutes and adjust with A. Press G once to exit.

How do I activate the alarm?

Press and hold B, then press A to toggle the alarm flag on/off. When the flag appears, the alarm is active. It will sound for 20 seconds or can be silenced by pressing A.

How do I use the stopwatch?

Press A to start timing, press A again to stop. Press B to reset. Press G to return to regular time.

How do I use the split timer?

Press A to start. While timing, press B to freeze the screen (split), press B again to unfreeze. Repeat as needed. To reset, stop with A then press B.

How do I adjust the watch band?

Remove an equal number of links from both sides of the clasp. Use a sharp pointed tool to push out the pins from the recessed side. Pull pins out with needle-nose pliers. Rejoin links and ensure pins are flush. Professional adjustment recommended.

How do I use the Indiglo backlight?

In any mode, press the H button to illuminate the LCD display. This is an electroluminescent backlight for better visibility in the dark.

How do I set the chime?

Press and hold B, then press G to toggle chime on/off. The chime is active when the alarm flag is shown (all day) and deactivated when the flag disappears.

What should I do if my watch stops or runs slow?

This likely indicates a low battery. Replace the coin cell battery with a new one (type CR2032 or equivalent). We recommend having it replaced by a professional to avoid damage.

USER MANUAL 19093 Stauer

A - Month, Date and Day of Week Button.

B - Alarm-Time.

C - Crown

D - Minute Dial

E - Seconds Dial

F - Hour Dial

G - Stop Watch function.

H - Indigo Light

TIMESETTING

Locate the crown on your Stauer watch (see diagram part C). Please note the two crown positions (0-1) in part C of diagram.

1. To set the time: Pull the crown out to position "1" (see diagram part C) which will allow you to position watch hands for proper time selection. Rotate the crown clockwise until the desired time is set.

2. When finished setting the time, push the crown back to the "0" (zero) position.

SETTING THE DIGITAL DISPLAY TIME

Press the "G" button three times: This will start time in setting mode. The "seconds/E" will start flashing.

1. Press the "B" button: The "MIN" will flash. Press "A" button to advance.

2. Press the "B" button: The "HOUR" will flash. Press "A" button to advance.

3. Press the "B" button: The "DATE" will flash. Press "A" button to advance.

4. Press the "B" button: The "MONTH" will flash. Press "A" button to advance.

5. Press the "B" button: The "Week-DAY" will flash. Press "A" button to advance.

6. Press the "G" button: Return to the regular-time display.

SETTING THE ALARM

Press & hold the "B" button: Alarm Time will show.

1. Press the "G" button twice: Alarm Time, "Hour" Flashes, Press "A" button to advance.

2. Press the "B" button once: Alarm Time, "Min" Flashes, Press "A" button to advance.

3. Press the "G" button once: Alarm Time setting-mode is complete, & will return to regular time read-out.

SET ALARM FUNCTION

Depress & Hold the "B" button, and press "A" button, Alarm "FLAG" will appear.

If you hear the alarm-sound, this will stop itself after 20 seconds, or can be silenced by pressing the "A" button. (the alarm will go off again same time the next Day.)

CHIME SETTINGS

Press & hold the "B" button and press "G" button to adjust Chime.

1) Chime is activated by Turning-On the Alarm setting, and the all day "FLAG" appears

2) Deactivate Chime by Turning-Off the alarm setting, and the all day "FLAG" disappears.

TIMESETTING CONT.

STOP WATCH FUNCTION

1. Press "A" to start timing, to stop press "A" again.

2. To reset timer press "B".

3. Press the "G" button to return to regular time.

SPLIT TIMER

1. Press "A" to start timing.

2. Press "B" to freeze the screen.

3. Press "B" again to unfreeze the screen.

4. Repeat steps 5 & 6 to split the time again.

5. To zero out the count timer repeat steps 1 & 2.

6. Press the "G" button to return to regular time reading.

In all time-modes, you can press the “H” button to illuminate LCD display for better viewing.

FEATURES

- Hour, Minute, second, day of the week, Month and Date functions.

- Split second function.

- Alarm with Chime.

- 12 / 24 Hour Display for user's option.

- Maximum Counting:23 Hrs 59 Min 59 Sec

- E. L Back- Light Function.

ADJUSTING CLASPS

To adjust the band: Remove equal number of links from both sides of the closure by carefully sliding out the pins in each link. To do this, you will need to use a sharp pointed tool. Insert it into the recessed side of the link. With a solid tap, push the pin out until it is easy to pull the pin using needle nose pliers. Once the required amount of links are removed, join the remaining links together using the removed pins. It is necessary to secure the pins in place by making sure that they are flush with one side of each link. To ensure that watch is fitted properly, we recommend that your Stauer watch be handled by a professional.

Visit us at, www.stauer.com to learn more about the fantastic benefits of owning a Stauer Watch! www.stauer.com

HERITAGE OF ART & SCIENCE
Stauer Hybrid Watch

INSTRUCTION MANUAL