SRS4-14 - Meuble audio-video encastrable Middle Atlantic - Free user manual and instructions

Brand	Middle Atlantic
Model	SRS4-14
Product Type	Sliding Rack Shelf / Rack Rail System
Mounting Style	19-inch rack-mountable
Construction Material	Steel (estimated)
Sliding Mechanism	Ball-bearing sliding carriage with rail stops
Locking Panel	Included for security
Squaring Panel	Included for equipment alignment
Cable Carrier	Optional (sold separately)
Mounting Points	12 points for secure attachment
Warranty	3 years from date of shipment
Compliance	ISO 9001 Registered Company
Maintenance	Clean with a dry, soft cloth; avoid abrasive cleaners
Included Hardware	Mounting screws, locking panel, squaring panel, rail stops
Intended Use	Professional AV equipment rack mounting

Frequently Asked Questions - SRS4-14 Middle Atlantic

How do I install the SRS4-14 sliding rack shelf?

Position and center the SRS in your millwork with the desired setback. Use two preliminary mounting holes to attach it, then remove the locking panel and slide the rack out. Secure using all 12 mounting points. Attach the rackrail to the sliding section with provided hardware. Finally, install the squaring panel about 1/3 down from the top of the rackrail.

What is the weight capacity of the SRS4-14?

The weight capacity is not explicitly stated in the manual. However, due to its steel construction and sliding mechanism, it is designed to support typical AV components such as amplifiers, patch panels, and small to medium-sized gear. For heavy loads, ensure proper installation and consider using additional support.

Is the cable carrier included with the SRS4-14?

No, the cable carrier is an optional accessory that must be purchased separately. If used, it should be installed before attaching the rackrail. Instructions for the cable carrier are provided on page 2 of the manual.

Can I adjust the rail stops?

Yes, the rail stops maintain a plumb position when the rack is closed. Mount two stops per side in the highest possible position while maintaining contact with the backside of the rackrail in the closed position. Wood screws for this attachment are provided.

What tools are needed for installation?

You will need a screwdriver (likely Phillips), a wrench or socket for hex bolts, and possibly a level. The manual mentions hardware provided, so check the included kit for specific sizes.

How do I clean and maintain the SRS4-14?

Clean the surface with a dry, soft cloth to remove dust. For stubborn dirt, slightly dampen the cloth with water. Avoid using abrasive cleaners or solvents that may damage the finish. Periodically check and tighten all mounting screws.

What is the warranty period for Middle Atlantic SRS series?

Middle Atlantic warrants the SRS Series to be free from defects for a period of 3 years from the date of shipment. This warranty covers material and workmanship under normal use. It does not cover damage from misuse, accidents, or unauthorized modifications.

Can the SRS4-14 be used in any 19-inch rack?

Yes, the SRS4-14 is designed for standard 19-inch rack mounting. The manual mentions compatibility with millwork, but it can also be installed in standard rack cabinets. Ensure the depth and mounting hole alignment match your rack.

How do I attach the rackrail to the sliding section?

Use the hardware provided to attach the rackrail to the sliding section. Finger tighten only initially. After installing the squaring panel and loading some equipment, final tighten the rackrail to the sliding section to ensure proper alignment.

Are there any safety precautions I should follow during installation?

Yes. Always follow the assembly instructions carefully. Ensure the rack is securely mounted to the millwork using all 12 mounting points. Do not exceed the load capacity. Use caution when sliding the carriage to avoid pinching fingers. If using the optional cable carrier, install it per the manual to prevent cable damage.

USER MANUAL SRS4-14 Middle Atlantic

ASSEMBLY INSTRUCTIONS

Interior view of a black rack-mounted audio workstation with CD and DVD units, no visible text or symbols on the equipment.

THANK YOU

Thank you for purchasing the SRS Series. Please read these instructions thoroughly before installing/assembling this product.

NOTE: If optional cable carrier is used it must be installed prior to rackrail. (See PAGE 2)

Technical line drawing of a mechanical bracket with mounting holes and a vertical plate (no text or symbols)

1) Position and center SRS in millwork with setback desired.
2) Using 2 preliminary mounting hole locations attach the SRS to the millwork.

3) Remove "Locking Panel" and slide rack out

4) Secure SRS using 12 mounting points indicated in drawing.

5) Attach rackrail to the sliding section using hardware provided, finger tighten only.

6) Install squaring panel approximately 1/3 of the way down from the top of the rackrail using hardware provided. NONOTE: The squaring panel remains in place until some of the equipment is loaded.

7) Final tighten the rackrail to the sliding section.

8) Test the sliding carriage operation. Adjust mounting positions as necessary should interference with the millwork occur.

9) Attach the Locking panel.

10) Rail Stops serve to maintain a plumb position when rack is closed. Mount 2 stops per side in the highest position possible while maintaining contact with the backside of the rackrail in the closed position. Wood screws are for this provided attachment. (see illustration above)

OPTIONAL

SRS Cable Carrier Instructions

NOTE: Carefully examine drawing for details of which side hinge mounting panel goes to

1) Attach the Hinge Mounting Plate to the rear surface of the SRS bottom pan with four 10-32 socket head screws.

2) Attach the Cable Carrier Hinge to the rear of the Hinge Mounting Panel with four 10-32 socket head screws.

3) Attach front of Cable Carrier to the SRS Chassis with four 10-32 socket head screws

Technical line drawing of a mechanical assembly with bolts and brackets (no text or symbols)

SRS Series rough-in pan mounting point locations

Middle Atlantic Products

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the SRS Series to be free from defects in material or workmanship under normal use and conditions for a period of (3) three years from date of shipment by the Company.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection thereof at the Company's factory. This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.

Corporate Headquarters

Corporate Voice 973-839-1011 - Fax [phone] / International Voice [phone] - Fax [phone]

middleatlantic.com - [e-mail]

Middle Atlantic Canada

Voice 613-836-2501 - Fax [phone] / middleatlantic.ca - [e-mail]

Factory Distribution

USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 Registered Company.

30% Recycled Paper