PXMFTS-100 - Multifunction tool Ozito - Free user manual and instructions

Brand	Ozito
Model	PXMFTS-100
Product Type	Cordless Multi Function Tool
Power Source	Battery (cordless)
Speed Control	Variable speed dial
Accessories Included	Sanding pad, sandpaper (3×60 grit, 3×80 grit, 3×120 grit), wood plunge blade, metal plunge blade, semi-circular blade, scraper, accessory adapter
Battery Compatibility	Ozito battery (sold separately)
Warranty	5 years
Handle	Sure Grip Handle for comfort
Vibration Absorption	Yes, between battery and tool seating
Maintenance	Keep ventilation slots clean; blow air after use; no lubrication; store in dry, frost-free location
Safety Feature	On/Off switch with lock; requires battery removal before accessory changes
Compatible Accessories	Standard multi-tool accessories (with adapter if needed)

Frequently Asked Questions - PXMFTS-100 Ozito

How to insert and remove the battery?

Slide the battery into the seating at the back of the tool until it clicks into place. To remove, press and hold the battery release tab and slide out.

How to change accessories?

Ensure the tool is switched off and battery removed. Rotate the accessory locking lever anti-clockwise to open the spindle. Place the accessory onto the drive spindle, aligning holes with notches. Tighten the lever.

How to adjust the speed?

Rotate the variable speed dial to a higher number to increase speed. Lower numbers for slower speed.

What accessories are included with the PXMFTS-100?

Includes: sanding pad, 9 sheets of sandpaper (3×60, 3×80, 3×120 grit), wood plunge blade, metal plunge blade, semi-circular blade, scraper, and accessory adapter.

How to use the tool for sanding?

Attach the sanding pad to the spindle. Press sandpaper onto the pad, aligning holes. Use a slight pendulum motion while sanding. Suitable for wood, plastic, and painted surfaces.

How to use the sawing function?

Secure the workpiece and ensure blade is not blunt. Attach the appropriate plunge blade. Switch on and use a pendulum motion while cutting. Suitable for wood, plastic, and sheet metal.

What maintenance is required?

Keep ventilation slots clean. After use, blow air through the housing. No lubrication needed as bearings are sealed. Store in a dry, frost-free location out of children's reach.

What safety precautions should I follow?

Always read the manual. Wear eye protection. Keep work area clean and well-lit. Do not use in explosive atmospheres. Disconnect battery before maintenance. Use a residual current device (RCD) if operating in damp locations.

How long does it take to charge the battery?

Initial charge requires 5 hours. Subsequent charges take 3-5 hours. The battery reaches optimum charge after 4-5 charge cycles.

Does the tool have a warranty?

Yes, it comes with a 5-year warranty. To make a claim, return the product to your nearest Bunnings store. The warranty covers defects under normal use.

USER MANUAL PXMFTS-100 Ozito

Line drawing of a mechanical device with 'ozito' branding, no readable text or symbols beyond the label

STANDARD EQUIPMENT

Multi Function Tool

Accessories

5 YEAR

PXMFTS-100

WARRANTY

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS

The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law.

KNOW YOUR PRODUCT SETUP & PRE

CORDLESS MULTI FUNCTION TOOL

1. Accessory Lacking Lever

4Battery Seating

20n/Off Switch

1. Accessory Drive Spindle

2. Variable Speed Dial

3. Sure Grip Handle

ACCESSORIES

7 Sending Pad

10 Metal Flunge Blade

8Sarding Paper

11 Semi-Circular Blade

(3 × 60grit, 3 × 80grit, 3 × 120grit)

13 Scupper

9 Wood Plunge Blade

13 Accessory Adapter

RATION

1. FITTING THE BATTERY

Inserting & Removing the Battery

1 Slide the battery into the seating at the back of the tool until it clicks into place.

2 To remove, press and hold the battery release tab and then slide out.

Vibration Absorption

To absorb the vibrations which arise on the rechargeable battery, there is some play between the battery and the tool's battery seating. This is normal and has no effect on the performance of the equipment or the rechargeable battery.

2. FITTING ACCESSORIES

ENSURE THE TOOL IS SWITCHED OFF AND THE BATTERY IS REMOVED BEFORE PERFORMING ANY OF THE FOLLOWING TASKS.

Attaching Accessories

1. Rotate the accessory locking lever anti-clockwise to open spindle finnt.

2 Place the desired accessory onto the accessory drive spindle ensuring the holes in the accessory align with the notches on the tool.

Diagram of a mechanical component with red arrows indicating force or movement (no text or symbols)

3 When using other non-Ozito multi function tool compatible accessories, the accessory adapter may need to be fitted to secure correctly.

3. CONTROLS

Turning On and Off

1 To start the tool press the on/off switch forward into the on position.

2 To stop the tool press the on/off switch backward into the off position.

AFTER USE, HOLD THE TOOL AWAY FROM YOUR BODY UNTIL THE SPINDLE STOPS COMPLETELY.

Variable Speed Control

1 To increase the speed of the tool, rotate the variable speed dial to a higher number.

OPERATION

4. SANDING

With the sanding pad and sand paper fitted, the multi function tool can be used on materials such as wood, plastic and painted surfaces.

Fitting Sand Paper

1 The sanding pad must first be fitted to the spindle following the instructions in the previous section.

2 Press the sanding paper onto the sanding pad by aligning the edges and holes

Two triangular objects with holes and a central circle, one larger and one smaller, connected by a red arrow (no text or symbols)

3 To remove, peel away from the sanding pad starting from an edge.

5. SAWING AND SCRAPPING

Sawing or Cutting

When sawing, the multi function tool can be used on wood, plastic and sheet metal using the correct accessory.

Note: Ensure blades are not blunt or damaged in any way before commencing.

1 Ensure the work piece is securely held down and the accessory is secure.

2 Switch the tool on use a slight pendulum motion while cutting.

Technical diagram of a mechanical component with a red directional arrow indicating rotation (no text or symbols)

Scraping

When being used as a scraper, the tool can remove materials such as fabric, adhesives, vinyl or paint from wood, plastic and metal.

1 Ensure the necessary is secure

MAINTENANCE

ALWAYS ENSURE THE TOOL HAS LY STOPPED AND THE BATTERY IS PRIOR TO ANY MAINTENANCE.

• Keep ventilation slots of the multi function tool clean at all times to ensure efficient operation.
• After each use, blow air through the tool housing to ensure it is free from all dust, dirt, etc. Build up of dust, dirt particles may cause the tool to overheat and shorten the life of the tool.
• If the housing of the multi function tool requires cleaning, do not use solvents but a moist soft cloth or soft brush only.
• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.
• No lubrication is necessary as the tool has sealed bearings.
• When not in use, the multi-function tool should be stored in a dry, frost free location not within the reach of children.

Note: Czito Industries will not be responsible for any damage or injuries caused by the repair of the multi function tool by an unauthorised person or by mishandling of the multi function tool.

DESCRIPTION OF SYMBOLS

V	Volts	Hz	Hertz
ac/-	Alamating current	W	Watts
dc/-	Elect current		Diameter
mA	Milliamporax Ah Amp hour
	Regulatory Compliance Mark (RCM)	No	No load speed
	Warning		Read instruction manual

TROUBLESHOOTING

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall outlet.

Check the battery is firmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

The battery has a short run time

Ensure the battery is properly charged. It will take 4-5 charging cycles before the battery reaches optimum charge and run time. On the initial charge, the battery requires 5 hours of charging. Subsequent charging only requires 3-5 hours.

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

ELECTRICAL SAFETY

WARNING! When using mains-personal tools, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage.

Used the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool. Save these instructions and offer a quarter-controlled with this tool for experience.

In order, the company has granted for 750K and 740K only. Australia has the power supply correspond to the unit price of the company.

The time change is double in total, the amount is not required.

The application is target, it will be replaced by an electric power transfer in the circuit board. Note: Double resistance can not be a phase of normal wire penetration after operating this test. The current system is the ideal electrode assembly, scaling for the product of industrial facilities within the field.
Always use an approxed actor or fixed suitable for the power input of this test. Before use, inspect the extension load for signs of dynamic action and operation. Explains the actors or actual operational balance.
After using an extension load at a roof, always around the case completely. Use of an extension load not suitable for the power output. The load is which to cover or select the extension load in which it is possible after
The power supply for this product manager should be protected by a residual current device (used at 32 mA or less). A residual current device is defined as the risk of solar or ice.

Using an Extension Load

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to lose the warnings and reporting well in specific cases, he/she is not sure.

Since all warnings and instructions for future reference. The term "power tool" in the warnings

refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1. Work area safety

Keep work soon down and wait it. Dates reese to be

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power-take costs equals which navigate the doctor notes.

Keep children and byzanders away while operating a power tool. Detection system is

2. Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with sorted (grounded) power tools. Unusual chips and retarding outlets will value risk.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is a increased net of charge sheet every box in an heater rounded

Do not expose power tools to rain or wet conditions. When entering a power too will increase the ice crystal smoke shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Jirrings or interpolated ends represent the industrial disk.

1. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use the end suitable for outdoor use reduces the risk of a grid shock

If operating a power tool in a dump location is unavailable, use a residual current device (RCD) protected supply. Use clar if RCD requires the next electrical switch.

3. Personal safety

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A proper action on this exercise is important to say you're doing it.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust and sandblasting, dust, air, and water. We use the equipment to ensure reliable quality.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Applying power tools of their motor on the bolted or passive power loss that leads the switch in motion as sorts.

- Removes any adjusting key or research before turning the power tool on. A written be set attached to a listing part of the power put may read, in several injury.

1. Do not overreach. Keep proper footing and balance at all times. This means better result of the power
   Dross properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts, jeans clothes, ewels or etc. they can be carried up every
   If devices are provided for the connection of dust extraction and collection facilities, ensure
   these are connected and properly used, the first other can note a non-lined route. Do not let familiarity gained from frequent use of tools allow you to become complicate and ignore tool safety principles. A case is action on cause where injury within a tract or of a second.
   Do not force the power tool. Use the correct power tool for your application, to correct power
2. Do not use the power tool if the switch does not turn it on and off, any one or that can be
   • Do not use the power bus in the sixth class. • produce with a mix this to remove input (a project)
3. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Subcutaneous small measures include the load of storing the power tool accidentally.
4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Few tools are large in the hands during one
5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, from the power tool repaired before use, here is said are caused by both maintained power tools.
   Keep cutting tools sharp and clean. Paper, maintained cutting tool will shop cutting edge or collar, or bind and are easier to control
   Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use all the power tool or equipment offered from the steel and wood for a working situation.
6. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slipper handles and grasping surfaces are not allowed for solid handling and several of the metal in unexpected sources

4. Power tool use and care

5. Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will serve for service of basic units required.