MicroTalk CX312 - Walkie-talkie COBRA - Free user manual and instructions

Product Type	Two-Way Radio (Walkie-Talkie)
Brand	Cobra
Model	MicroTalk CX312
Dimensions (H x W x D)	5.0 x 2.5 x 1.2 inches
Weight (with batteries)	3.6 ounces
Power Supply	3 x AAA alkaline batteries (not included)
Frequency Band	FRS (Family Radio Service) / GMRS (General Mobile Radio Service)
Channels	22 channels
Privacy Codes	121 tone codes (38 CTCSS / 83 DCS)
Range (typical)	Up to 16 miles (26 km) in ideal conditions
Output Power	0.5 watts (FRS compliant)
VOX (Voice-Activated Transmission)	Yes, with adjustable sensitivity
Scan Function	Yes, scans channels for activity
Weather Alerts	NO (no weather channels)
Battery Life	Approximately 20 hours (typical use)
Low Battery Indicator	Yes, audible and LED alerts
Display	Backlit LCD with channel and code display
Keypad Lock	Yes, prevents accidental channel change
Microphone	Built-in electret condenser
Speaker	0.3 watt, 8 ohm built-in
Antenna	Fixed flexible antenna
Belt Clip	Included, detachable
Wrist Strap	Included
Operating Temperature	14°F to 122°F (-10°C to 50°C)
Dust/Water Resistance	Not rated, avoid moisture
Maintenance	Wipe with dry cloth; do not use solvents
Safety	Do not operate near explosives or flammable gases
Spare Parts / Repairability	No user-serviceable parts; contact Cobra support
Accessories (Optional)	Earpiece/microphone (sold separately)

Frequently Asked Questions - MicroTalk CX312 COBRA

What is the maximum range of the Cobra MicroTalk CX312?

Under ideal conditions (open area with no obstructions), the maximum range is up to 16 miles (26 km). In urban or wooded areas, range is typically 1-2 miles due to buildings and terrain.

What type of batteries does the CX312 use and how long do they last?

The radio uses 3 AAA alkaline batteries (not included). Battery life is approximately 20 hours with typical use (5% transmit, 5% receive, 90% standby). Use of rechargeable Ni-MH batteries is supported but be aware that voltage may be slightly lower.

How many channels does the CX312 have and are there privacy codes?

It has 22 channels (FRS/GMRS). It also supports 121 privacy codes (38 CTCSS tones and 83 DCS codes) to reduce interference from other users.

Does the CX312 have VOX (voice-activated transmission)?

Yes, the CX312 features VOX mode with adjustable sensitivity levels. When enabled, you can transmit hands-free by speaking into the microphone.

Can I listen to weather channels on this radio?

No, the MicroTalk CX312 does not include NOAA weather channels or weather alerts. It is a basic two-way radio without that feature.

Is the CX312 compatible with other brands of walkie-talkies?

Yes, it can communicate with any other FRS or GMRS radio set to the same channel and privacy code. Many brands use standard frequencies and tones.

How do I clean and maintain my CX312?

Turn off the radio and remove batteries. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the contacts clean and dry. Avoid exposing to water or extreme temperatures.

What safety precautions should I take while using the CX312?

Do not operate the radio near explosives, flammable gases, or in hazardous environments. Do not use while driving unless in hands-free mode. Use only approved accessories. Keep out of reach of small children.

Can I use rechargeable batteries in the CX312?

Yes, you can use rechargeable AAA Ni-MH batteries. Note that rechargeable batteries have a lower voltage (1.2V vs 1.5V for alkaline), which may slightly affect range and battery indicator accuracy. Always recharge in a proper external charger.

Where can I find a user manual for the CX312?

The manual is available for free download on notice-facile.com or the Cobra website. You can use the AI question feature to ask about specific functions.

USER MANUAL MicroTalk CX312 COBRA

For Assistance in the U.S.A.

In this user's manual, you should find all the information you need to operate your microTALK® radio. If you require further assistance after reading this manual, Cobra Electronica offers the following customer assistance services:

Automated Help Desk

English only. 24 hours a day, 7 days a week, 773-889-3067 (phone)

Customer Assistance Operators

English and Spanish, 8:00 a.m. to 5:30 p.m. Central Time, Mercisu through Friday (except holidays) 773-889-2087 (phone).

Questions

English and Spanish. Faxes can be received at 773-622-2209 (fax)

Technical Assistance

English only. www.cobra.com (on-line: Frequently Asked Questions) English and Spanish. [e-mail] (e-mail).

For Assistance Outside the U.S.A.

Contact Your Local Dealer

chro Electronics Corporation

Chicago, Illinois 50706 U34

www.csc10.com

Product Features

1. Avenia
2. External Spesken
   MierphoneCharge Jack
3. Mode/Power Button
4. Weather/Lock Button
5. Channel
   Buttons
6. Backlit LCD Display

7 Speaker/Microphone
6. Volume Up/Down Buttons
9 Light/Max Range Button
10. Talk Button
1. Call Button
12. Wrist Strap Connection
13. Bet Clip
14. Battery Compartment

1. Battery Door Lath

Product Features

Features

• 22 Channels
Seven shared
(1) FRESSES.
seven FRS only.
eight SARS only

• 10 Channel

Weather Radio

(1) 2017年1月1日

- Weather Alert

• 121 Privacy Codes

(35 CTCSS codes

23 DCS online

• Heads-Free Operation

- hands-free operation YOU

- Fact

- Brain Chasein

CHINA

public

- Backlit LCD Display

• Call Alert

Fair selectable

0158

Dull, L.

• Button Lock

• Speaker!

Microphone

Charge Jack

a Spring Day

• Roger Bldg Selachie Co.

(1) 2017年1月1日

- Battery/Power Saver

• Kauwokka Towns

• Keystone Tules

• Battery Level

Indicator

• Auria Spanish

- Auto Equation

• Maximum

Range Extend

[Non-Text]

Backlit LCD Display

1. Battery Level Indicator

2. VOX Ibon

Scan Icon

1. Roger Dee

2. Lock Ison

3. Low Down

4. Low Power IEC

1/other men

1. Weather 1051

2. Vicalther, Bird Jeans

3. DECEITORS DIVER

4. DOS/CTCOS Privacy Code Number 10

5. Channel Numbers

6. Время/Трансии

7. 2023年1月28日星期六

Important FCC Licensing Information

This radio operation on General Mail. Basic Service (GMS) recurrence when required a Federal Communications Commission (FCC) license. Blue page 19 for Licensing and other relevant information.

Maximum range may vary and is based on uncalculated line-of-light communication under ideal conditions.

Warranty and Trademark Acknowledgement

Limited One-Year Warranty on Radio(s)

For Products Purchased in the U.S.A

Cobra Electronics Corporation warrants that its Cobra microTALK® radices and the component parts thereof, will be free of defects in workmanship and materials for a period of one year from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A.

Cobra will, without charge, repair or replace, at its option, defective microTALK radios, products or component parts upon delivery to the Cobra Factory Service department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.

You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Colors's expense, if the product is repaired or replaced under warranty. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Exclusions: This limited warranty does not apply: 1) In any product damaged by accident; 2) In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs; 3) If the serial number has been altered, detached, or removed; 4) If the owner of the product resides outside the U.S.A.

All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty. Cakes shall not be liable for any incidental, consequential or other damages, including, without limitation, damages resulting from loss of use or cost of installation. Some statutes do not allow limitations on how long an implied warranty lasts anchor do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not escape to you

For Products Purchased Outside the U.S.A.

Please contact your local dealer for warranty information.

90-Day Warranty on Rechargeable Batteries

For products purchased in the U.S.A. and Canada

Trademark Acknowledgement

Cobra®, microTALK®. Nothing Comes Close to a Cobra®, VibeAlert® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics Corporation™ is a trademark of Cobra Electronics Corporation, USA.

Nothing Comes Goes to a Cobra!

Introduction

Caring for Your microTALK® Radio

Your microTALK® radio will give you years of trouble-free service if cared for properly. Handle the radio gently. Keep the radio away from dust. Never put the radio in water or in a damp place. Avoid exposure to extreme temperatures.

Installing Batteries

To install or replace batteries:

1. Remove belt clip by releasing belt clip latch and sliding clip up.
2. Pull up on the battery door latch to remove the holiday compartment cover.
3. Insert three AA rechargeable batteries or non-rechargeable alkaline batteries. Position beliefs according to polarity markers
4. Replace battery compartment cover and bell clip.
5. Do not attempt to charge alkaline batteries.
6. Do not mix old and new batteries.
7. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
   To charge batteries in radio:
8. Check to see that the batteries have been inserted properly.
9. Insert the cable into the charge jack located at
   the top of the radio.
10. Plug the cable into USB-compatible power port.

Cobra recommends your radio is turned off while being charged. Non-rechargeable alkaline batteries can also be used in your radio. If you are planning to buy NiMh batteries, please purchase Cobra supplied batteries only.

Using Your Radio

Operative

Quick Start

1. Press and hold the Mode/Power button to turn on your radio.

2. Press the Channel Up or Channel Down button to select a channel.

Both radios must be tuned to the same channel/privacy code to communicate.

1. Press and hold the Talk button while speaking into the microphone.

2. When finished talking, release the Talk button and listen for a response.

Turning on Your microTALK® Radio

Press and hold the Mode/Power button until you hear a series of audible tones indicating the radio is on. Your microTALK® radio is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode except when the Talk, Call or Mode/Power buttons are pressed.

Battery Status Indicator

Indicator

The battery charge status is shown on the display. Four bars indicates fully charged.

Battery Low

When battery power is low, the final bar in the Battery Low icon will blink and an audible icon will sound twice before the radio shuts off. Your batteries should be replaced or recharged, if using rechargeable batteries.

The radio will display flashing battery icon while charging if the radio is on.

Auto Battery Save

If there are no transmissions within 10 seconds, the radio will automatically switch to Power Save mode and the Power Saver icon will flash in the display. This will not affect the radio's ability to receive incoming transmissions.

Communicating with Another Person

1. Press and hold the Talk button.
2. With the microphone about two inches (5 cm) from your mouth, speak in a normal voice.
3. Release the Talk button when you are finished talking and listen for a response. You cannot receive incoming calls while pressing the Talk button.

Both radics must be tuned to the same channel to communicate.

To Select a Channel

With the radio on, select any of the 22 channels by pressing the Channel Up or Channel Down button.

Both radios must be tuned to the same channel to communicate.

Channels 1 through 7 are shared with FRS/GMRS. Channels 8 through 14 are FRS only. Channels 15 through 22 are GMRS only. See page 14 for FRS/GMRS frequency allocations and compatibility charts.

Using Your Radio

Listening for a Response

Release the Talk button to receive incoming transmissions. Your microTALK ^® radio is always in Standby mode while the Talk or Call buttons are not pressed.

To Adjust Vol

Press the Volume Up or Volume Down button. A double beep sound is used to indicate the minimum and maximum volume levels (1 through 9).

Call Button

Press and release the Call button. The other person will hear a two-second call tone. This tone is used only to establish voice communications. See page 12 on how to select between five call tone settings.

To Illuminate Display

Press and release the Light/Max Range button to illuminate the display.

Auto Squelch/Maximum Range

Your microTAUR radio will automatically shut off weak transmissions and unwanted noise due to terrain, conditions or if you've reached your Maximum Range limit.

You can temporarily turn off auto squelch or turn on maximum range extender, allowing all signals to be received and extending the maximum range of your radio.

To temporarily turn off auto squelch: Press the Light/Max Range button for less than five seconds.

To turn maximum range extender on: - Press and hold the Light/Max Range button for at least five seconds until you hear two beeps which indicates the maximum range extender is on. To turn maximum range extender off: - Press and release the Light/Max Range button or change channels.

Lock Function

The Lock function locks the Channel Up, Channel Down and Mode/Power buttons to prevent accidental operation.

To turn the lock on or off: - Press and hold the Lock button for two seconds. A double beep sound is used to confirm your lock on or off request. When in Lock mode, the Lock icon will be displayed.

A double beep sound is used to confirm your lock on or off request. When in Lock mode, the Lock Icon will be displayed.

microTALK® Range

Your range will vary depending on terrain and conditions. Maximum Range In flat, open country your radio will operate at maximum range. Buildings and foliage in the path of the signal can reduce the range of the radio. Dense foliage and hilly terrain will further reduce the range of the radio. On RFS Channel 8 through 14, your radio automatically switches to low power, which will limit the range the radio can communicate. Reduced Range Remember: you can achieve maximum range by using maximum range according to see page 4 for details.

Nothing Comes Goes to a Cobra ^®

Using Your Radio

Scrolling Through the Mode Function

By scrolling through the Mode function, you will be able to select or turn on preferred features of your microTALK® radio. When scrolling through the Mode function, your radio features will be displayed in the same predetermined order:

Set CTCSS Privacy Codes Set DCS Privacy Codes Set Vox OrvOff Set Vox Sensitivity Set Channel Scan Set CTCSS Privacy Code Scan Set DCS Privacy Code Scan Set Cell Tones Set Roger Boep OrvOff

Privacy Codes

Your microTALK radio incorporates two advanced coded squelch systems that can help to reduce interference from other users on any given channel. CTCS (Continuous Tone Coded Squelch System) provides 38 privacy codes and DCS (Digitally Coded Squelch) provides 83 privacy codes. This provides a total of 121 Privacy Codes. Either system can be used on all channels, but both systems cannot be used on the same channel at the same time.

To successfully communicate using a privacy code, both the sending and receiving radios must be tuned to the same channel and to the same privacy code system (CTCSS or DCS) and privacy code number. Each channel will remember the last privacy code system and number you select.

The privacy code 00 is not a privacy code, but allows all signals to be heard on a channel that is set to 00 on both the CTCSS and DCS systems.

Set CTCSS Privacy Codes

To select a CTCSS privacy code:

1. After selecting a channel, press the Mode/Power button until the CTCSS icon appears and the small numbers next to the channel number flash on the display.

If DCS is turned on at the channel selected, the display will flash the CTCSS icon and "OFF." To switch from DCS to CTCSS, press the Channel Up or Channel Down button while the display is flashing "OFF." The display will then show the email numbers flashing and you will then be able to proceed to step 2.

1. Press using the Channel Up or Channel Down button to select a privacy code. You can hold the Up or Down button for fast advance.
2. When your desired CTCSS privacy code is displayed, choose one of the following: a. Press the Mode/Power button to enter the new setting and proceed to other functions.
   b. Press the Lock button to enter the new setting and return to Standby mode.
   c. Do not press any buttons for 15 seconds to enter the new setting and return to Standby mode.

Mode Functions

Set DCS Privacy Codes

To select a DCS privacy code: 1. After selecting a channel, press the Mode/Power button until the DCS icon appears and the small numbers flash on the display (01 through 83). If CTCSS is turned on at the channel selected, the display will flash the DCS icon and "OFF." To switch from CTCSS to DCS, press the Channel Up or Channel Down button while the display is flashing "OFF." The display will then show the small numbers flashing and yo will then be able to proceed to step 2.

1. Press using the Channel Up or Channel Down button to select a DOS

2. When DCS privacy code is displayed, choose one of the following:

a. Press the Mode/Power button to enter the new setting and

proceed to other functions b. Press the Lock button to enter the new setting and return to Standby mode.

c. Do not press any buttons for 15 seconds to enter the new setting and return to Standby mode.

Voice Activated Transmit (VOX)

In VOX mode, your microTALK® radio can be used "hands-free," automatically transmitting when you speak. You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise.

1. Press the Mode/Power button until the VOX icon flashes on the display. The current On or Off selling is displayed.

2. Press the Channel Up or Channel Down button to turn VOX On or Off.

3. Choose one of the following: a. Press the Mode/Power button to enter the selected On or Off setting and proceed to other functions. b. Press the Lock button to enter the selected On or Off setting and return to Standby mode.

To set VOX sensitivity:

1. Press the Mode/Power button until the VOX icon flashes and the current sensitivity level is displayed.

The current VOX sensitivity level is displayed with letters "LE" and a Number 1 through 5, with Number 5 being the most sensitive level and Number 1 being the least sensitive level.

1. Press the Channel Up or Channel Down

button to change the setting.

1. Choose one of the following: a. Press the Mode/Power button to enter the selected setting and proceed to other functions.

b. Press the Lock button to enter the selected setting and return to Standby mode.

Mode Functions

Channel Scan

Your microTALK ^® radio can automatically scan channels.

During scanning (while receiving an incoming transmission),

you can choose from the following:

a. Press and hold the Talk button to communicate on that channel.
Your radio will remain on that channel and return to Standby mode
b. Does the Channel Up or Channel Down button to resume
b. Pleas the channel scanning channels
scanning channels
c. Press the Lock button to return to Standby.

During scanning (while receiving an incoming transmission).

you can choose from the following:

a. Press and hold the Talk button to communicate on that channel/privacy code. Your radio will remain on that channel/privacy code and return to Standby mode.
b. Press the Channel Up or Channel Down button to resume scanning privacy codes. If you do not press any button within 10 seconds, your radio will automatically resume scanning privacy codes.
c. Press the Lock button to return to Standby.

Privacy Code Scan

Your microTALK radio can automatically scan the Privacy Codes (either
CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only
one set of private code (ICTSS or DOS) can be scanned at a time.

To scan privacy codes:

1. While in Standby mode, press the Channel Up or

Channel Down button to choose the channel on

which you wish to swap private codes.

which you want to court privacy codes.

1. Press the Mode/Power button until either the

CTCSS or the DCS icon appears on the display

and the Scan icon and the privacy code number

flash on the display.

1. Pass 500 Channel Unit or Channel Down Button

2. Press the channel up of channel down button to begin scanning privacy codes within the

to begin scanning privacy codes within the

channel you selected.

During scanning (while receiving an incoming transmission).

you can choose from the following:

a. Press and hold the Talk button to communicate on that channel

rebeau code. Your radio will remain on that channel/rebeau code

privacy issues. Your risks will remain on that challenge privacy issues and return in Standby made.

and return to Standby mode.

b. Press the Channel Up or Channel Down button to

resume scarring privacy codes. If you do not press any button

within 10 seconds, your radio will automatically resume scanning

privacy nodes

Primary School

c. Press the Lock button to return to Standby.

Nothing Comes Closes to a Cobra ^®

Mode Functions

Five Call Tone Settings

You can choose between five different Call Tone Settings to transmit a call alert.

To change a call tone setting:

1. Press the Mode/Power button until the letter "C" and the current call tone number (01 through 05) is displayed. The current call tone will be found for one second.
2. Press the Channel Up or Channel Down button to hear the other call tone settings.
3. Choose one of the following: a. Press the Mode/Power button to enter the new setting and proceed to other functions. b. Press the Lock button to enter the new setting and return to Standby mode.

Roger Beep Confirmation Tone

Your listener will hear an audible tone when you release the Talk button. This alerts the other party that you are finished taking and it is OK for them to speak.

To turn roger beep on or off:

1. Press the Mode/Power button until the Roger Beep icon flashes. The current on or off setting is displayed.
2. Press the Channel Up or Channel Down button to select roger beep on or off.
3. Choose one of the following: a. Press the Mode/Power button to enter the new setting and return to Standby mode. b. Press the Lock button to enter the new setting and return to Standby mode.

Weather Radio Channels

You can use your microTALK radio to listen to weather channels transmitting in your area.

To listen to Weather Radio channels: 1. Press the Weather button until the WX icon and the currently selected weather channel is displayed.
2. Use the Channel Up or Channel Down button to change weather channels. 3. The WX weather icon will continue to be displayed when in weather mode. 4. To exit weather mode, press and hold the Weather button until On or Off is displayed.

Weather (WX) Alert Mode

Turning On the Weather Alert function will allow your radio to automatically receive NOAA Hazard Alert radio signals and warnings from designated NOAA broadcast stations. If the radio is turned ON, it will alert to Weather and other emergency alerts broadcast by NOAA.

Make sure the strongest Weather channel is selected for your area using the NOMA AI Hazards Radio Channels selection in the previous menu.

To turn Weather Alert On or Off:

1. Press the Weather/Lock button until the Weather Alert icon flashes on the display. The current On or Off setting is displayed.
2. Press the Channel Up and Channel Down button to turn Weather Alert On or Off.
3. Press and hold the Weather/Lock button again to save the new setting and exit the Weather Alert Mode and return to Standby mode.

This radio is rain resistant to JIS3 standards.

Nothing Comes Coes to a Cobra ^®

General Specifications and Licensing

General Specifications

FRS/GMRS Frequency

Allocation and Compatibility

Important: Please note that Cobra GMRS models with 15 Channels may designate different channel numbers for the same frequency. For example, a Cobra 16 Channel GMRS model would need to be tuned to Channel 11 in order to communicate with a 22 Channel GMRS tuned to Channel 15. Please refer to the chart below for channel frequency number compatibility.

A = Channel No. for 22 Channel FRS/GMRS Models

B = Channel No. for 15 Channel GMRS Models

C = Type of Radio Service D = Frequency in MHz

E = Frequency in

ABCDE

1	1	FRS/CMRS	462.5625 High
2	2	FRS/CMRS		462.5675 High
3	3	PRS/CMRS	462.6125 High
4	4	FRS/CMRS	462.6375 High
5	5	FRS/CMRS	462.6625 High
6	6	FRS/CMRS	462.6875 High
7	7	FRS/CMRS	462.7125 High
	8		FHS		467.5625 Low
	9		FHS		467.5675 Low
	10		FHS		467.6125 Low
	11		FHS		467.6375 Low
	12		FHS		467.6625 Low
	13		FHS		467.6875 Low
	14		FHS		467.7125 Low
15	11	CMRS		462.6500 High
16	8		CMRS		462.6750 High
17	12	CMRS		462.6920 High
18	9		CMRS		462.6950 High
19	13	CMRS		462.6100 High
20	10	CMRS		462.6700 High
21	14	CMRS		462.7000 High
22	15	CMRS		462.7350 High

IMPORTANT NOTICE: FCC LICENSE REQUIRED

This flow may vary accounts on GNAS (Recent Mobile Radio Services) recommendations which require an FCC Financial Communications Commission. License, a user must be registered prior to operating on Instagram: 1 through 7 on rich power or 16 through 22, which comprise the GNAS accounts of this radio. Serious generators could result for unemployment and job losses in the U.S. during the period of the year. Operation of this radio is subject to additional rules applied in 47 C.F.R. Port S5. Licensed users will be issued as a sign by the FCC, which should be used for platform identification when operating this radio. GNAS users should also constitute by engaging in permissive transactions only, avoiding discharge interference within other GNAS users, and being resident with the length of their permission time. For: Licensing information and application forms, please call the FCC herein at 800-4100-FORD. Request form #196 and form #305. Questioning regarding the license applications should be directed to the FCC or BISL 64.1. FCC is provided in the following form: 1 through 7 on rich power or 16 through 22. Channel 1 through 7 on rich power and channels 2 through 7 to participate the FCC Specialty Radio Services, but license is required to operate on the PRS.

Safety information for microTALK Radios

Your wireless handset provides transmission to a low power transmitter. When the link button is posted, it sends our radio frequency in a suitable time. The decision is authorized to operate at a duty factor rate to prevent GPS. In August 1968, the Federal Communications Commission (FCQ) subscribed FF exposure guidelines with safety levels for handheld wireless devices. Important FCQ FF Exposure Requirements For body water operation. This radio has been issued and meets the FCO FF exposure guidelines when used with color accessories as specified or designed for this project. Use of other accessories may not ensure compliance with FCO FF exposure guidelines. Use only the supplies antenna. Unfinished antenna, modifications or attachments could damage the transmission and may manage FCO regulations.

Normal Position

Find the transmitter approximately 2 inches from your face and speak in a normal voice, with the arbena pointed up and away.

This choice complies with part 15 of the FOS Rules. Operation is subject

to the following two cordless 31. The device may not be used to

In the case of the first time, we have

ECG: Wannow, Backwasser) or a relation of transistors, required codes or

other parts of a unique nature, with parts other than those recommended by

Gon may raise a version of the federal regulations of part 35 of the IC2

rules, or violation of type acceptance requirements of plan 2 of the rule

Nothing Comes Goes to a Cobra ^®

Product Service

Product Service Questions

For any questions about operating or installing this new Cobra product, or if parts are missing...PLEASE CALL COBRA FIRST...do not return this product to the store. See customer assistance on page AI.

For Products Purchased in the U.S.A.

If your product should require factory service, please call Cobra first before sending your radio. This will ensure the fastest turn-around time on your repair. You may be asked to send your radio to the Cobra factory. It will be necessary to furnish the following to have the product serviced and returned.

1) For warranty repair include a copy of the original sales receipt. If you need the original receipt, it cannot be refunded.

2) Send the entire product.

3) Enclose a detailed description of the problem along with the name and address of where the product is to be returned.

4) Pack radio securely to prevent damage in transit. If possible, use the original packing material.

5) Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or Priority Mail to avoid loss in transit to Cabra Factory Service:

Cabra Electronics Corporation

6500 West Corlund Street

6) If the radio is under warranty, it will be repaired or exchanged depending on the model.

Please allow approximately three to four weeks before contacting Cobra for status. If the radio is out of warranty, a letter will automatically be sent informing you of the repair charge or replacement charge. If you have any questions, charges and 379,000,000 for purposes.

For Products Purchased Outside the U.S.A.

Please contact your local dealer for product service information.