TA 1400 - Tea Maker Rommelsbacher - Free user manual and instructions

Product Type	Tea Maker & Water Kettle
Brand	Rommelsbacher
Model	TA 1400
Power Supply	220-240 V~ 50/60 Hz
Nominal Power	1200 - 1400 W
Protection Class	I
Standby Consumption	< 0.5 W
Water Capacity	0.5 L (min) - 1.2 L (max)
Number of Programmes	6 (Herbal, Black, Oolong, White, Green, Heat up)
Brewing Temperature Range	50 °C - 100 °C (adjustable in 5 °C steps)
Steeping Time Range	30 sec - 10 min (adjustable in 30 sec steps)
Keep Warm Function	Yes, 30 minutes at selected temperature
Quick-Start Boiling	Yes, dedicated BOILING button
Display	Digital with temperature and time indication
Material of Jug	Glass
Base Unit Material	Plastic
Accessories Included	Tea infuser, lid, lid insert for infuser
Decalcification Interval	Every 2-3 weeks
Safety Features	Overheat protection, auto shut-off, cool-touch handle
Cleaning	Wipe base with damp cloth; wash infuser, lid, and insert in hot soapy water (not dishwasher)

Frequently Asked Questions - TA 1400 Rommelsbacher

What is the minimum and maximum water capacity of the TA 1400?

The minimum filling quantity is 0.5 L and the maximum is 1.2 L. Observe the MIN and MAX markings on the glass jug to avoid overflow.

How do I select a tea program?

Press the MENU button to cycle through the 6 programmes: Herbal (100°C/6min), Black (100°C/3min), Oolong (90°C/3min), White (80°C/3min), Green (70°C/3min), and Heat up (100°C). The display shows the selected programme.

Can I adjust the brewing temperature and steeping time?

Yes. Press ▲ or ▼ to change temperature in 5°C steps (50-100°C). Press TIME/TEMP to switch to time mode, then adjust steeping time in 30-second steps (30s-10min). To memorize the new settings, press and hold TIME/TEMP for 2 seconds until a signal tone sounds.

How does the keep warm function work?

After the steeping time ends, the appliance automatically keeps the tea warm at the selected brewing temperature for 30 minutes. The display shows the elapsed keep warm time. If the jug is removed, you have 10 minutes to replace it and press START to resume.

What is the quick-start boiling function?

Press the BOILING button at any time to heat water to 100°C. The appliance will boil the water and then switch to selection-mode (programme 1 Herbal). There is no steeping phase.

How do I clean and descale the TA 1400?

After each use, wipe the base unit and glass jug with a damp cloth. Wash the infuser, lid, and lid insert in hot soapy water (not dishwasher). For descaling, mix 1/3 vinegar essence with 2/3 water, heat to about 80°C using the BOILING button, let it sit, then rinse. Repeat every 2-3 weeks.

What should I do if the display shows error code E1?

Error E1 indicates overheating. Unplug the appliance and let it cool down completely. Do not use cold water to cool it. After cooling, plug in and restart. If the error persists, contact service.

Can I use the appliance without the tea infuser?

Yes. Select programme 6 (Heat up) or use the BOILING button to simply heat water. The infuser is only needed for tea brewing programmes.

Why is the tea quantity less than the water I filled?

Tea leaves absorb water, and some water evaporates during heating. This is normal. The reduction depends on the type and amount of tea used.

Is the appliance safe to leave unattended?

No. Although it has safety features like overheating protection and auto shut-off, never leave the appliance unattended during operation. Always unplug after use.

USER MANUAL TA 1400 Rommelsbacher

Circular geometric pattern with vertical lines and a curved base (no text or symbols)

ROMMELSBACHER

Black-and-white photo of a Rommelsbacher water heater with digital display and glassware on a table (no visible text or symbols)

TA 1400

Tee- & Wasserkocher Tea maker & Water kettle

Produktbeschreibung – Product description

Control panel with display 3

Introduction 17

Intended use 17

Technical data 17

Scope of supply 17

Packing material 17

Disposal/recycling 17

For your safety 18

General safety advices 18

Safety advices for using the appliance ..... 19

Prior to initial use 20

Standby mode 20

Selecting programme, brewing temperature, steeping time 20

keep warm function 20

Operating the appliance 21

1. Connecting the base unit 21
2. Filling up with water and placing the lid .. 21
3. Selecting programme/function 21
4. Modifying brewing temperature and steeping time 22
5. Starting the operation 22
6. Programme sequences 22
7. Quick-start function (BOILING) 24
8. Switching off 24

Cleaning and maintenance 25

Cleaning the appliance 25

Decalcification 25

Troubleshooting 26

Signal tone 27

Bedienungsanleitung

Einleitung

Close-up of a metallic kettle with black and silver casing (no visible text or symbols)

Close-up of a metallic kettlebell with a black arrow pointing to the dial (no visible text or symbols)

Close-up of a transparent glass teapot with a black arrow pointing to the lid (no text or symbols visible)

We are pleased you decided in favour of this high-quality appliance and would like to thank you for your confidence. Its easy operation and wide range of applications will certainly fill you with enthusiasm as well. To make sure you can enjoy using this appliance for a long time, please read through the following notes carefully and observe them. this instruction manual safely. Hand out all documents to third persons when passing on the appliance. Thank you very much.

Intended use

The appliance is designed for heating water and making tea for domestic use only (in the kitchen, at table, in office, etc.). Other uses or modifications of the appliance are not intended and harbour considerable risks. For damage arising from not intended use, the manufacturer does not assume liability. The appliance is not designed for commercial use.

Technical data

Only connect the appliance to an isolated ground receptacle installed according to regulations. The rated voltage must comply with the details on the rating label. Only connect to alternating current.

Nominal voltage: 220-240 V\~ 50/60 Hz

Nominal power: 1200 - 1400 W

Protection class: I

keep warm function: 30 minutes

Standby consumption: < 0.5 W

Scope of supply

Check the scope of supply for completeness as well as the soundness of the product and all components (see product description page 2) immediately after unpacking.

Packing material

Do not simply throw the packing material away but recycle it. Deliver paper, cardboard and corrugated cardboard packing to collecting facilities. Also put plastic packing material and foils into the intended collecting basins.

PE-HD

PE-LD

PP

PS

In the examples for plastic marking PE stands for polyethylene, the code figure 02 for PE-HD, 04 for PE-LD, PP for polypropylene, PS for polystyrene.

Disposal/recycling

According to the Waste Electrical and Electronic Equipment Directive, this product must not be disposed of with your normal domestic waste at the end of its life-span. Therefore, please deliver it at no charge to your appropriately licensed local collecting facilities (e.g. recycling yard) concerned with the recycling of electrical and electronic equipment. Please approach your local authorities for how to dispose of the product.

For your safety

WARNING: Read all safety advices and instructions. Non-observance of the safety advices and instructions may cause electric shock and/or bad injuries!

General safety advices

• Always children under 8 away from the product and the power cord.
- Children from the age of 8 must be supervised when cleaning or maintaining the appliance.
- Children from the age of 8 and persons not having the knowledge or experience in operating the appliance or having handicaps of physical, sensorial or mental nature must not operate the appliance without supervision or instruction by a person, responsible for their safety. Never leave the appliance unattended during operation.
- Children should be supervised in order to ensure that they do not play with the appliance.
- Packing material like e. g. foil bags should be kept away from children.
- Do not operate this unit with an external timer or a separate telecontrol system.
- Prior to each use, check the appliance and the attachments for soundness. It must not be operated if it has been dropped or shows visible damage. In these cases, the power supply must be disconnected and the appliance has to be checked by a specialist.
- When laying the power cord, make sure that no one can get entangled or stumble over it in order to avoid that the appliance is pulled down accidentally.
- the power cord away from hot surfaces, sharp edges and mechanical forces. Check the power cord regularly for damage and deteriorations. Damaged or entangled cords increase the risk of an electric shock.
- Only use the original accessories.
- Do not misuse the power cord for unplugging the appliance!
- Never immerse the glass jug, base unit, power cord and power plug in water for cleaning.
- Do not store the appliance outside or in damp rooms.
- This electrical appliance complies with the relevant safety standards. In case of signs of damage to the appliance or the power cord, unplug the appliance immediately. Repairs may be executed by authorised specialist shops only. Improper repairs may result in considerable dangers for the user.
- Improper use and disregard of the instruction manual void all warranty claims.

Safety advices for using the appliance

WARNING: Hazard of injury and burns!

• The surfaces of appliance, glass jug, lid, lid insert, tea infuser as well as the liquids are getting hot during use and firstly stay hot after switch-off.
• Mind the hot steam coming out when removing the lid from the glass jug or the lid insert for the infuser respectively. Use e. g. a tea towel to protect your hands from scalding!
• Do not overfill the jug (observe the max. filling quantity)! Spilling and overflow during operation might cause hazard of scalding!
• The tea jug is made of glass. In case of breakage mind the sharp and pointed edges!
• Do not use a damaged tea jug!

Thus, act with caution:

• Before connecting the appliance mind to check the proper sitting of the tea jug and that the water container is filled sufficiently with water (observe the filling capacity of at least 0.5 l or max. 1.2 l).
• To avoid overflow the maximum filling capacity of 1.2 l must not be exceeded. Switch off and unplug the appliance immediately in case of spilling water!
• The central base with electrical connection must always be clean and dry. No water may be spilled on electrical connections!
• Let the appliance cool down before filling water into the water container. Only use cold tap water for this appliance.
• Do not heat other liquids like e. g. milk or similar.
• Only operate the appliance with jug lid in place. Do not remove the lid during operation.
• Do not use the appliance as a storing place and do not cover it during use.
• Observe the following when setting up the appliance:
  o Place it beyond children's reach.
  o Place the appliance on a heat-resistant, stable and even surface.
  o Do not operate the appliance in the vicinity of sources of heat (oven, gas flame etc.) or in explosive environments, where inflammable liquids or gases are located.
  o Leave a ventilation distance of at least 20 cm to all sides to avoid damage by heat or steam and to grant an unobstructed work area.
  o Make sure there are no objects or furniture sensitive to heat or moisture above the appliance. Make sure steam can draw off easily!
• Never operate the appliance without water.
• Do not handle the appliances with hands wet.
• For a safe switch-off pull the mains plug after each use.

Prior to initial use

- Prior to the first use it is necessary to clean the appliance and its accessories. Please refer to point "Cleaning and maintenance" for further information.

Standby mode

The appliance features a standby mode. In standby mode the display of the appliance is off.

• In case the base unit is connected to the mains and there is no further activation of any button within 1 minute, the appliance switches over to standby mode.
• When the glass jug is placed on the base unit already connected to the mains and there is no further activation of any button, the appliance switches over to standby mode and the display goes off.
• The appliance switches over to standby mode about 1 minute after the operation (incl. keep warm function) has been completed.
• Pull the mains plug after each use to ensure a safe switch off!

Selecting programme, brewing temperature, steeping times

The electronic control allows for choosing between 6 different programmes (5 tea types with pre-defined brewing temperatures/steeping times plus water kettle function with temperature selection).

The preset temperatures and steeping times can be individually adjusted to your personal taste and be memorized as well.

The table below shows the preset brewing temperatures and steeping times (default values):

programme	display	preset brewing temperatures (*)	preset steeping times (**)
1 Herbal	(fruit/herbal tea) 100 °C 06:00 minutes
2 Black	(black tea) 100 °C 03:00 minutes
3 Oolong	(Asian tea type) 90 °C 03:00 minutes
4 White	(white tea) 80 °C 03:00 minutes
5 Green	(green tea) 70 °C 03:00 minutes
6 Heat	up 100 °C ---
(*) the brewing temperature can be set and memorized from 50 °C – 100 °C in 5 °C steps(**) the steeping time can be set and memorized from 30 sec. – 10 min. in 30 sec. steps

Keep warm function

The appliance is equipped with a 30 minute keep warm function. This function is pursuant to the selected brewing temperature. The table below shows the temperature defaults.

brewing temperature

50 °C

55 °C

60 °C

65 °C

70 °C

75 °C

80 °C

85 °C

90 °C

95 °C

100°C

keep warm temperature

ca. 50 °C

ca. 55 °C

ca. 60 °C

ca. 65 °C

ca. 70 °C

ca. 75 °C

ca. 80 °C

ca. 85 °C

ca. 90 °C

Operating the appliance

WARNING: Hazard of injury and burns!

• The surfaces of appliance, glass jug, lid, lid insert, tea infuser as well as the liquids are getting hot during use.
  • Hot surfaces firstly stay hot after switch-off.
• Do not overfill the jug as hot liquid might spill over!

1. Connecting the base unit

• Connect the power plug to a properly fused socket.
  • The appliance switches into selection-mode.
• A signal tone sounds and the display shows programme 1 "Herbal".

Note: If no further button is activated within 1 minute, the appliance will switch over to standby mode and the display goes out.

2. Filling up with water and placing the cover

Note: In case the appliance is in standby mode, lifting the jug will put it into selection-mode. The display shows programme 1 "Herbal".

• Lift the glass jug from the base unit.
• Fill the glass jug with cold tap water. Observe the "MIN" and "MAX" marking. See to it that no water will spill on the central base or the underside of the jug.

Close-up of a metallic kettlebell with black and white casing (no visible text or symbols)

Close-up of a metallic teapot with a black arrow pointing to the lid area (no text or symbols visible)

Close-up of a mechanical component with a black arrow pointing to a circular opening (no visible text or symbols)

• Put the lid on the glass jug. Ensure a proper fitting.
• Fit the lid insert for the tea infuser in the jug's lid (position OPEN) and screw it to the right (CLOSE position).
• Put the lid on the glass jug.
• Place the glass jug on the base unit.

3. Selecting programme/function

Note: The standby mode can be switched to selection-mode by pressing any button (except BOILING button).

• The display shows programme selection 1 "Herbal".
• Choose between the different preset programs by pressing the "MENU" button.

• It is possible to switch between the display of temperature and time by pressing the "TIME/TEMP" button.
• The display will return to show the temperature after about 4 seconds.

4. Modifying brewing temperature and steeping time (if necessary)

a) Modifying the brewing temperature

o Press the "▲" or "▼" button until the desired temperature is displayed.
o The temperature can be altered in steps of 5 from 50 °C to 100 °C.

b) Modifying the steeping time

o Press the "TIME/TEMP" button to enter the time-mode. The display shows the set time.
o Press the "▲" or "▼" button until the desired time is displayed.
o The time can be varied in 30-second steps from 30 seconds up to 10 minutes.

c) Memorizing temperature or steeping time

To permanently memorize the changed parameters, press the "TIME/TEMP" button for at least

2 seconds. A signal tone will confirm the successful modification.

5. Starting the operation

- Once the desired setting has been completed, the appliance can be started by pressing the "START" button.

6. Programme sequences

Note: The tea preparation comprises 4 phases in total. The programme "Heat up" consists of phase "1" only.

Programme phase ① - heating water

Note: In case the glass jug is lifted from the base during this phase, the appliance will stop and return to selection-mode.

graph LR
    A["Herbal"] --> B["30 °C"]
    B --> C["Herbal 100 °C"]

o The water is heated to the set temperature.
o As of 30 °C the display shows the current temperature in steps of 5 °C.
o There is a 5-times signal tone to indicate that the set temperature has been reached.

Programme phase ② - insert tea infuser

Note: In case the glass jug is lifted from the base during this phase, the appliance will stop and return to selection-mode.

o The display shows "10:00": There are 10 minutes left to insert the tea infuser and to activate the steeping time. If there is no activation, the programme gets cancelled and the appliance switches over to selection-mode. The time counts back in steps of 1 second.

o Unlock the small lid insert for the tea infuser by turning it to the left. Take it out.
o Insert the filled infuser into the opening of the jug's lid. The filling quantity of the tea infuser depends on your individual taste, the type of tea and the amount of water.
o Place the lid insert for the tea infuser into the jug's lid. Screw it to the right for locking (mind the OPEN and CLOSE marking).

Warning: Mind the hot steam coming out when removing the lid insert for the tea infuser. Use e.g. a tea towel to protect your hands from scalding!

o Press the START button to start programme phase ③ (activation of steeping time).

Programme phase ③ - activating the steeping time

Note: In case the glass jug is lifted from the base during this phase, the appliance will stop and return to selection-mode.

o Press the "START" button. A signal tone will sound and the steeping time begins.
o The display shows the remaining time counting down.
o There is a 6-times signal tone to indicate that the set steeping time has run down.

Removing the tea infuser after steeping time has run down

o Now remove the tea infuser.
o To do so, disengage the small lid insert for the tea infuser by turning it to the left. Take out the insert.
o Grip the infuser at its handle and lift it out
o Then close the lid again by inserting the lid insert again. Turn it to the right for locking (mind the OPEN and CLOSE marking).

Warning: Mind the hot steam coming out when removing the lid insert for the tea infuser. Use e.g. a tea towel to protect your hands from scalding!

Attention: Be cautious when removing the tea infuser – hot liquid might drip!

Programme phase ④ - keep warm function

Note: In case no keep warm function is required, the programme can be interrupted at any time by just pressing the "START" button for 2 seconds or unplugging the unit from the mains.

o The appliance switches over to keep warm function automatically for 30 minutes.
o The display shows the keep warm time in ascending order.

Removing the jug during the keep warm cycle

o In case the glass jug is removed during the keep warm cycle, the keep warm time will pause.

o After the glass jug was removed, the display shows "10:00". Now there are 10 minutes left to put the jug back in order to continue the keep warm cycle. If the jug is not put back, the programme will be stopped and the appliance switches over to the selection-mode. The time counts back in steps of seconds.

Mind: The keep warm function will not be continued automatically.

After the jug has been put back, the keep warm function can be continued by pressing the "START" button anew.

Once the keep warm time has run down, there is a 6-times signal tone and the appliance will switch over to standby mode.

7. Quick-start function (BOILING)

• The appliance has a quick-start button for bringing water to the boil.
  • There is no preset order for this function.
  o To activate the quick-start function just press the "BOILING" button.
  o The appliance commences the boiling, indicated by a short signal tone.
  o As of 30 °C the display shows the current temperature in steps of 5 °C.
• Once the boiling has been completed, the appliance automatically switches over to selection-mode.
• The display shows the programme selection 1 "Herbal".

8. Switching off

• The running programme or function can be interrupted any time. The appliance is set in selection-mode.
• To do so, press the "START" button for 2 seconds or unplug the power plug from the mains.
  • After each use pull the mains plug to ensure a safe switch off!

Cleaning and maintenance

WARNING: Hazard of injury or burns!

• Always pull the mains plug prior to cleaning!
- Never immerse base unit, glass jug, power cord and mains plug in water nor clean under running water!
- Prior to cleaning let cool down the appliance and all accessories!

Cleaning the appliance

• Clean appliance and accessories after each use.
• Wipe the base unit and glass jug with a moist cloth and dry it afterwards.
• Wash tea infuser, jug's lid and lid insert for the tea infuser in hot dishwater and dry it afterwards.

o Discolorations at the glass jug or the tea infuser can be removed by using a special brewer cleaner (for coffee makers etc.), which is obtainable in specialist shops.

o You may alternatively use a solution of water with salt, baking soda or lemon juice.

• We recommend not cleaning the accessories in the dishwasher.
- Do not use abrasives or solvents; do not use sharp, scratchy objects!
- Do not treat the appliance or the accessories with a steam jet cleaner!

Decalcification

• A regular decalcification saves energy, grants full heating power and a long lifespan of the appliance.
• A thick layer of limescale may cause an overheating of the appliance and cause irreparable damage.
• The appliance should be descaled regularly to grant a proper functioning. Depending on the water hardness and the frequency of use, we recommend a decalcification every 2 - 3 weeks. This also applies if filtered water was used.
• Observe the following instructions for decalcification!
  • Always remove the tea infuser before descaling the appliance.
• For decalcification prepare 1 litre descaling agent (vinegar in water) by mixing 1/3 vinegar essence with 2/3 water and pour it into the glass jug.
• Operate the appliance through the "BOILING" button and heat up the liquid to about 80 °C. Then stop heating by either pressing the "START" button for about 2 seconds or removing the jug from the base unit.
• Allow to act on for some time.
• Then drain the descaling solution, rinse the glass jug and fill it with 1 litre of clear tap water.
• Operate the appliance 1x via the "BOILING" button and bring the water to the boil. Repeat this procedure as often as required.
  • Afterwards wipe the tea jug thoroughly.
• In case you use ordinary descaling agents observe the manufacturer's instructions.

Important: Non-observance of the decalcification instructions will void all warranty rights in case of claims caused by a faulty functioning due to excessive limescale deposits!

Troubleshooting

Detection Cause and remedy
Appliance has no function • Check if the plug is connected properly.• Check the mains outlet by connecting a different appliance for testing.• Check if power cord or plug are damaged. If so, do not use the appliance.
Appliance cannot be switched on • Check if the glass jug sits properly on the base unit.
The display shows error code “E1” • The appliance is overheated. Unplug and let it cool down. Do NOT use cold water for cooling!Then start the appliance anew.
Phase 3 (steeping time) cannot be started after phase 2 (inserting the infuser) has been completed	• The current water temperature is higher than the set brewing temperature. Wait until the water has cooled down to the set brewing temperature.Then re-start phase 3 by pressing the "START" button!
Appliance makes loud running noise during heating-up	• Appliance is scaled. Run a decalcification cycle as per instructions!
Tea making requires more time than usual	• Appliance is scaled. Run a decalcification cycle as per instructions!
Quantity of ready tea is less than quantity of filled water	• Mind that each tea type absorbs and s a different quantity of water. This is the reason why the tea quantity is less that the water quantity before. In addition during brewing a certain amount of water will vaporize as well.
Glass jug and/or tea infuser take on the odour of the used tea type	• The materials of glass jug and tea infuser might take on the odour of especially intense tea types (e. g. peppermint or other herbals) and also get discolorations. This is normal and no reason for complaint! Clean jug and infuser as per instructions.

Signal tone

This appliance features an electronic control where every activated function is confirmed by one or more acoustic signals.

Action Signal tone
plug in the mains plug	1 x 2.5 sec.
start programme	1 x 0.25 sec.
stop programme manually	1 x 2.5 sec.
set temperature reached	5 x 1 sec.
reminder that set temperature has been reached (+120 sec.)	5 x 1 sec.
start steeping time manually	1 x 2.5 sec.
steeping time completed	1 x 2.5 sec. + 5 x 1 sec.
reminder that steeping time has been completed (+ 40 sec.)	1 x 2.5 sec. + 5 x 1 sec.
end of keep warm time	1 x 2.5 sec. + 5 x 1 sec.
error E1	1 x 8 sec.
memorize change of brewing temperature and steeping time	1 x 1 sec.
open the change of parameter during phase 1	1 x 0.25 sec.
memorize the change of parameters during phase 1	1 x 0.25 sec.