CPV14-VI-P8-1/8-D - Uncategorized Festo - Free user manual and instructions

Product Type	Multiple Connector Plate for CPV Valve Terminal
Brand	Festo
Model	CPV14-VI-P8-1/8-D
Compatible Valve Terminal	CPV14 series
Mounting Cut-out Dimensions (P8)	A=42.6 mm, B=114.5 mm, C=55.6 mm, D=96 mm, N=6
Number of Screws (P8)	6
Screw Type	Corrosion-resistant M5 screws per DIN EN ISO 4762
Screw Depth	7.5 mm to 9.5 mm
Tightening Torque	5 Nm ±10%
Protection Class	IP65 (when properly sealed)
Seals Included	Yes; 3 and 4-part seals for end plates
Sealing Surface Requirements	Flat, free of marks and scratches
Material	Metal/plastic (typical industrial grade)
Function	Electrical connection and sealing for valve terminals
Assembly Requirement	Press seals into holes, position plate from inside, fasten with screws
Torque Tolerance	±10%
Series Variants	P2, P4, P6, P8 (different number of slots)
Certification	DIN EN ISO 4762 (screws)
Manual Page Count	2 pages

Frequently Asked Questions - CPV14-VI-P8-1/8-D Festo

How do I install the multiple connector plate?

First, press the supplied seals into the holes of the CPV valve terminal. Then position the plate in the mounting cut-out from inside. Fasten with corrosion-resistant M5 screws to the specified torque.

What is the correct tightening torque?

The permitted tightening torque is 5 Nm ±10%. Over-tightening may damage the assembly.

What screw depth is required?

Select screw length l so that a screw depth of 7.5 mm to 9.5 mm is ensured. Depth less than 7.5 mm may not hold, more than 9.5 mm may damage components.

What protection class does it achieve?

When properly sealed and the sealing surface is flat, the assembly achieves IP65 protection against dust and water jets.

What are the dimensions of the mounting cut-out for P8?

For P8 type: A=42.6 mm, B=114.5 mm, C=55.6 mm, D=96 mm with N=6 screws.

Which valve terminals is this compatible with?

It is compatible with Festo CPV14 series valve terminals. The plate variant (P2, P4, P6, P8) must match the terminal configuration.

Are seals included?

Yes, seals are supplied. For multiple connector plates, both 3-part and 4-part seals for end plates are provided.

What tools are needed for assembly?

You need a suitable screwdriver or wrench for M5 screws. Additionally, a torque wrench is recommended to maintain the 5 Nm ±10% specification.

How do I maintain the connector plate?

Ensure the sealing surface remains flat and free of scratches. Periodically check screw tightness. No lubrication is required.

Can I use this plate with other valve terminal models?

This plate is specifically designed for Festo CPV14 series. Using with other models may not fit or achieve proper sealing. Consult Festo documentation.

USER MANUAL CPV14-VI-P8-1/8-D Festo

Isometric line drawing of a multi-tiered electrical connector with terminal blocks and connectors (no text or symbols)

$$ l - t = 7, 5 \mathrm{mm} \dots 9, 5 \mathrm{mm} $$

$$ 5 \mathrm{Nm} \pm 10\% $$

Technical illustration of a mechanical assembly with pins and a housing (no text or symbols)

2. Preparing for assembly

• Note the dimensions of the cut-out for fitting (→ Table).
  In order to comply with protection class IP65:
• Make sure that the surface near the sealing surface:
• is flat.
• is free of marks and scratches.

Mounting cut-out for

CPV14-VI-P...-D 1

Type	A ± 0.1	B ± 0.1	C ± 0.1	D ± 0.1	N
CPV14-VI-P...-D 1
P2	42.6	30.5	55.6	12	4
P4	42.6	58.5	55.6	40	6
P6	42.6	86.5	55.6	68	6
P8	42.6	114.5	55.6	96	6

3. Assembly

Isometric line drawing of a multi-tiered electrical connector with terminal blocks (no text or symbols)

• Press the seals 3 supplied into the holes in the CPV valve terminal.
• Note that the 3 and 4-part seals supplied with the end plates of the CPV valve terminal are only required with multiple connector plate [2].
• Position multiple connector plate 1 or 2 in the mounting cut-out from inside.

$$ l - t = 7. 5 \mathrm{mm} \dots 9. 5 \mathrm{mm} $$

• Fasten the multiple connector plate 1 or 2 with corrosion resistant N x M5 screws as per DIN EN ISO 4762.
• Select the screw length l as follows. A screw depth of at least 7.5 mm to max. 9.5 mm must be guaranteed.
• Tighten the screws. Maintain the permitted tightening torque.

For mounting the valve terminal:

- Observe the assembly instructions for the pneumatic section of the valve terminal.

Technical illustration of a mechanical assembly with pins and a housing (no text or symbols)