ACP-2415 - Compressor Ozito - Free user manual and instructions

Product Type	Air Compressor
Brand	Ozito
Model	ACP-2415
Dimensions (L x W x H)	50 cm x 30 cm x 50 cm
Weight	20 kg
Power Supply	230-240V ~ 50 Hz
Motor Power	1.5 hp (1100 W)
Tank Capacity	24 L
Max Pressure	8 bar (116 psi)
Air Delivery	200 L/min at 0 bar
Noise Level	75 dB(A)
Safety Features	Pressure relief valve, thermal overload protection
Maintenance	Drain water daily, check oil level weekly
Spare Parts	Available from Ozito service centers
Repairability	User-serviceable parts: air filter, pressure switch, valves
General Information	Portable compressor suitable for inflating tires, powering pneumatic tools

Frequently Asked Questions - ACP-2415 Ozito

What is the tank capacity of the Ozito ACP-2415 compressor?

The tank capacity is 24 litres, providing ample air storage for light to medium tasks.

What is the maximum pressure setting?

The maximum pressure is 8 bar (116 psi). Do not exceed this setting.

What type of oil should I use?

Use a SAE 30 non-detergent compressor oil. Check the oil level before each use.

How do I drain condensation from the tank?

Open the drain valve at the bottom of the tank daily to release moisture. Ensure the tank pressure is low.

Can I use an extension cord?

Yes, but use a heavy-duty cord with a minimum wire gauge of 14 AWG and keep it as short as possible.

What safety precautions should I take?

Always wear safety glasses and hearing protection. Never point the air stream at people or body parts.

How often should I check the air filter?

Inspect the air filter every 20 hours of operation and clean or replace it if dirty.

My compressor won't start. What could be wrong?

Check the power cord, thermal overload reset button, and ensure the pressure switch is in the 'on' position.

What is the recommended air pressure for tires?

Refer to the vehicle manufacturer's specification. Typically between 30-35 psi for passenger cars.

Where can I get spare parts?

Spare parts are available from Ozito authorized service centers or online retailers.

USER MANUAL ACP-2415 Ozito

Check the tank for signs of rust and damage each time before using. Do not use the compressor with a damaged or only tank

Cleaning

- Keep the safety devices free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

We recommend that you clean the appliance immediately after you use it.

Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive for the plastic parts in the appliance. Ensure that no water can get into the interior of the appliance.

You must disconnect the ho

compressor before cleaning. Do not clean the compressor with water, solvents or the like.

Removing

condensation water

The condensation water must be drained off each use by opening the drain plug, at the bottom of the tank. The drain plug can be opened by turning the screw in an anti-dockwise direction.

Cleaning the air filter

The air filter prevents dust and dirt being drawn in. It is essential to clean this filter after at least every 300 hours of service. A clogged air filter will decrease the compressor's performance dramatically.

... Remove the filter from the compressor by unscrewing the screw on the plastic cover.

Lift off the plastic cover and

Remove the intake air filter beneath.

. Carefully clean the filter by

stipping or blowing it with low pressure compressed air

(approte. 3 bar). To assemble proceed in reverse order.

5. STORAGE

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse.

For further information, or any parts not issued here, visit www.ozito.com.au or contact Ozito Customer Service: Australia 1800 069 486

New Zealand 0508 069 486 E-mail: [e-mail]

ELECTRICAL SAFETY

WARNING: When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage.

Read the above manual carefully and make sure you know how to switch the tool or in an emergency, before spreading the tool. Save these instructions and other documents supplied with this tool for future reference. The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. The tool is earthed in accordance with A5N25 60035-2002 Notes: This survey of 2018 (and 2019) are independent by Australia and Hong Kong.

If operating a power tool in a lamp location is unavoidable use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. If the supply cord is damaged, it must be replaced by an electrician or a power load repairer in order to switch RCD.

Using an Extension Lead Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power load of the tool or which is damaged or defective may result in a risk

GENERAL POWER TOOL SAFETY WARNINGS - PERSONAL SAFETY

Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (rented) power tool or battery-operated (wireless) power tool. 1. Block area safety

1. Keep work area clean and well lit. Cluttered or dark press invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of Rarmstadt liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with near-end (prombed) power loads. Unmutated plugs and matching sulfants will reduce risk of electric shock.

b. Avoid body contact with earthen or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthen or grounded.

c. De not-expose power tools to rain or wet conditions. Water entering a power tool will increase the risks of electric shock. d. De not abuse the sand. Never use the need for carrying, pulling or unplugging the power

1. Keep cord away from feet, oil, sharp-dages or moving parts. Damaged or enlarged cords increase the risk of elective shock.
2. When spending a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cont suitable for outdoor use reduces the risk of electric shock. If operating a power taxol in a damp location is unavoidable, use a residual current device (RCD) protected supply: Use of an RCD reduces the risk of electric shock.

1. Personal safety
2. Stay alert, watch what you are doing and see common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication

A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always near eye protection. Protective equipment

such as dust mask, non-lass safety shoes, helmet net, or hearing protection used for appropriate conditions will reduce personal injuries. 1. Prevent unidentional starting. Ensure the retail is in the off-position before connecting

d. Remove any adjusting key or wrench before turning the power tool on. A wrench of a key left attached to a totating part of the power tool may result in personal injury. d. Do not everreach. Keep proper feeling and balance at all times. This enables better control of the power tool in commercial situations.

Of the power too in unexplained conditions. F. Gross property. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

1. If devices are provided for the connection of dual exclusion and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

2. Power tool use and take

3. Do not force the power tool. Use the current power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect: the plug from the power source and/or the battery pack from the power tool

before making any adjustment, changing assessaries, or starting power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Stress info power tools out of the wards of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Whitmate power tools, if such for misalignment as kinds of motion parts, requires of

1. Maintain power tools. UNTK for misalignment of burning or blowing points, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained

- Keep rutting tools sharp and clean. Properly maintained rutting tools with sharp-rutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and their data etc. in accordance with these instructions, taking into account the working conditions and the work is to be performed. Use of the power tool for operations different from these intended could result in a hazardous situation.

1. Service a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

In. If the supply card is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

WARNING: Before connecting a tool for a power source (trains switch power joint receptacle, outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool

result in serious injury to the user, so well as damage to the tool. If in doubt, it is not plug in the tool, up a power source with a voltage less than the nameplate rating is harmful to the motor.

To reduce the risk of fire or explosion, never sprayy flammable liquids in a confined area. It is normal for the compressor motor and pressure outlet to produce sparks during use. If sparks come into contact with diesel vapours or sorrents, they may injite the vapours and cause a fire or explosion.

Always operate the compressor in a well ventilated area. Do not smoke while spraying. Do not spray where sparks or flames are present. Keep the compressor as far away from the spray area as possible.

The solvents trichloroethane and methylene chloride can chemically read with the aluminium used in some palm spray guns and form an explosion. If these solvents are used, ensure that only stainless steel spray equipment is connected. The compressor is not affected by the use of these

Ableeds. Never directly inhale the compressed air produced by a compressor and do not use it for charging breathing tanks.

Do not use welding equipment in bbls prokmity to the compressor. Do not use anything to the air tank of the compressor: this could dangerously weaken the tank and will void the warranty. Do not use the compressor outdoors when it is raining or on a wet surface; either situation could

Always shut off the compressor after use and before servicing. Push the on/off knob down, wait for the pressurized air to bleed from the tank from the release valve and then remove the electrical plug from the power supply.

Check the maximum pressure rating of any tools or accessories that you intend using with the compressor. The output pressure of the air from the compressor must be regulated so that it never secents the rated pressure of the tool or accessory.

To avoid the risk of burns and injury from moving parts, do not operate the compressor with the safety shield removed. Allow hot parts to cast before handling or servicing. Be uncertain to read all the labels on the containers of parts or other materials to be survived. Closely

follow all safety instructions. Use a respirator mask if there is a chance that you might otherwise inhale the spray materials. Carefully check the effectiveness of any respirator mask you intend using. Always wear safety goggles or glasses when using the air compressor. Never point the nozzle of an

necessary towards any joint of your body or towards another pension. Do not attempt to adjust the pressure switch or the release valve located under the pressure switch valves.

Drain the moisture from the tank daily. It will help prevent corrosion.

- Keep the compressor at local Journals from the request was to ensure adequate verification for cooling purposes. - Before transporting the compressor make sure that the pressurized air is dried from the tank and that the compressor is fully accounted.

- Protect the air hose and contact from damage. Inspect for weak or worn spots regularly and replace if necessary.

- Bursol using an extension cord with this product. Use additional air hose instead of an extension cord to prevent power ice and possible damage to the motor. Use of an extension cord voids the warranty. - The following periods external motor costs could be listed

- All long working periods external metal parts could be hot. - Always press the on/off button down is switch off the compressor before switching off the power or reminding the power plug.

- Under using the compressor, platon on the drive button, disconnect the power supply and open electrical valve to release the pressure. - Do not attempt to remove any part of the machine whilst it is under pressure.

- Use battery equipment including battery goggles or drums; bus (producers), mounting or friction masks and protective clothing. - Never attempt to remove any part of the compressor whilst the tank is under pressure.

She was a good, but the best of the person. She was a good, but the best of the person.

I be too much as users only for its predicted population, any user other than inside members in this manual will be considered a cause of release. The user and not the manufacturers shall be liable for any damage or injury resulting from such causes of release. The product are shall not be liable for any adverse events in the local area for any adverse conditions by

The international should not be liable for any changes made to the tool nor for any damage resulting in such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in corruption with the tool's construction and design

- Damage to the lungs if an effective breathing mask is not worn. - Damage to hearing if effective earmuffs are not worn. - Damage is the same if effective safety concerns or shield are not worn.

WARNING. In the event that an air line is cut or broken, the air supply must be turned off at the compressor. A broken air line which is not supported is extremely dangerous and can whip around very quickly. With the versatility of elite men, and blowout through particles into the air.

Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from the

YEAR REPLACEMENT WARRANTY

ACP-2415

WARRANTY

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 48

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.

The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law. Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above.

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the original date of purchase. If a product is defective it will

be replaced in accordance with the terms of this warranty. Warranty excludes consumable parts, for example: air filters and

WARNING

OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

KNOW YOUR PRODUCT

ONLINE MANUAL Scan this QF. Code with your mobile device to take you to the online manual.

SETUP & PREPARATION

1. ASSEMBLY 3. TROUBLE SHOOTING2.

Pre setup checks

- Examine the machine for signs of transit damage. If damaged, do not use, contact Qolio.

• The compressor should be set up near the area of use

- Avoid long air lines and long supply lines (extensions).

• Make sure the intake all is dry and cash-fed. • Do not set up the compressor in clamp or wet r

- The compressor may only be used in suitable rooms (with good

ventilation and an ambient temperature from 5°C to 40°C). There must be such a dry, uncoated, ablating vapor or inflammatory vapor in

be no cold, cold, vapour's, explosive gases or inflammable gases in the room.

• The compressor is designed to be used in dry rooms. It is prohibited

to use the compressor in Atlanta where work is conducted with sprayed water. Before you use the washing, make sure that the mains voltage

complies with the specifications on the rating plate.

Fitting the wheels

Note. You must fully answer

compressor before using it for the first time

1. Place a weather onto the bolt and fit the bolt into the wheel. New features and

bol into the wheel, NOW it washer and rufoc nut on the thread of the bolt and

tighten.

[Non-Text]

1. Insert the wheel bolt through the hole

in the wheel bracket, below the tank.

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

1. Form the inside of the vialool Implied

3 - From the value of the wheel scratch, place a spring washer on the wheel bol

Fasten the wheel bolt in position with a

(nuts and washers supplied).

[Non-Text]

[Non-Text]

[Non-Text]

1. Clin the hub can to the outer

face of the wheel.

5.2.1.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.58.59.60.61.62.63.64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.85.86.87.88.89.90.91.92.93.94.95.96.97.98.99.100

b. Repeat steps 1 to 4 with the second wheel

Bolivia 2019

RATION

Fitting the supporting foot

1. Align the hole in the supporting

foot with the hole in the supporting

foot bracket.

m = 311

Switching On/Off

1. Attach the desired tool to the

quick release regulated air

(3)

Adjusting the pressure

[Non-Text]

1. Once set up and On you can adjust

the air pressure by turning the pressure regulating knob.

1、本次发行的种类和面值

[Non-Text]

[Non-Text]

[Non-Text]

1. To increase the air pressure, rotate

the regulating knob clockwise. To decrease the pressure, relate the

decrease the pressure, rotate the regulating knob anti-clockwise.

。

Note. Air must be flowing through the

the attached air tool in order to obtain t

correct output reading on the pressure

Preset pressure

The minimum and maxi

tank pressure can be read from (the tank) pressure on the. This tank

the tank pressure gauge. This tank pressure is set at the factory and the

operator should not alter it.

2.1.1 2017年1月1日

Switch-on pressure 6 bar Switch off pressure 8 bar

Direct Port prestare o De

Note. When the maxims

tank pressure is reached, the motor the evaporated skin used. For new

the complicated air is used, the pressure will drop until it reaches the preset minimum pressure, when the minimum pressure is reached

the compressor will turn on again automatically to build up/maintain

pressure.

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

Checking the safety valve

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

Checking the safety valve

Turning Off

1. After the task

switch the con

printing down

[Non-Text]

[Non-Text]

[Non-Text]

[Non-Text]

2 Switch off the

and remove the

[Non-Text]

[Non-Text]

[Non-Text]

(五) 法律

1. Welcome first to the goal (blow our

(1) 2017年1月1日

Note: By pulling

Problem	Cause	Solution
The compressor (time not last)	1. No power supply	1. Check the power supply, including the power and its components, which are outside.
	2. Inufficient power supply	3. Rare uses that the power is not too long.
	3. Outside temperature to 50 °C	4. More open, where both are open and above it’s.
	4. Motor is overloaded	5. Allow the motor to a box down if frequently normally binds the motor, or otherwise, together.
The compressor still but there is no pressure	1. Look the low return value	1. Replaces the low return value
	2. The noise and damage	2. Check the noise and noise and any damage, then replaced by a serious noise.
	3. The dry plug level	3. Tighten the battery band check the seal on the floor, or replace it with the other.
The compressor still, pressure is shown on the pressure range to the other groups	1. Lose from connections	1. Check the connection to the air and beds and loads of the air and the lock.
	2. Look a stick-to-slick coupling	2. Check the stick-to-slick coupling and holds the recovery.
	3. Insufficient pressure not on the pressure	3. Open the pressure range.

YEAR REPLACEMENT WARRANTY

ACP-2415