C35 - Hand blender Bogen - Free user manual and instructions

Product Type	Hand Blender (Immersion Blender)
Brand	Bogen
Model	C35
Dimensions (approx.)	40 x 7 x 7 cm
Weight (approx.)	0.8 kg
Power Supply	220-240 V, 50/60 Hz, 300 W
Cord Length	1.2 m
Functions	Blending, Mixing, Pureeing, Chopping (with accessories)
Speed Settings	Variable speed with turbo boost
Material	Stainless steel blending shaft, plastic handle
Accessories Included	Beaker, whisk attachment, chopper attachment
Cleaning	Removable blending shaft; dishwasher-safe parts (beaker, whisk, chopper)
Safety Features	Safety lock, non-slip grip, automatic shut-off when overloaded
Spare Parts Availability	Blade assembly, shaft, sealing ring available separately
Repairability	User-replaceable shaft and blade; professional repair for motor
Warranty	2 years limited warranty

Frequently Asked Questions - C35 Bogen

How do I clean the Bogen C35 hand blender?

Disconnect the blender from power. Remove the blending shaft and rinse it under running water. The shaft, whisk, and chopper attachment are dishwasher-safe. Wipe the motor unit with a damp cloth; do not immerse in water.

Can I blend hot liquids with the C35?

Yes, but allow them to cool slightly to below 80°C to avoid damage. Use a tall container and immerse the shaft fully to prevent splashing.

How do I attach the whisk or chopper?

Ensure the blender is unplugged. Align the accessory with the motor unit and push gently until it clicks. Refer to the manual for specific attachment instructions.

What is the maximum blending time?

Do not operate continuously for more than 1 minute. Allow the motor to cool for 2 minutes between uses to prevent overheating.

Why is my blender not turning on?

Check that the safety lock is disengaged and the plug is properly inserted. If it still doesn’t work, press the reset button (if available) or contact customer support.

Can I use the blender without the beaker?

Yes, you can blend directly in any sufficiently tall container. Ensure the container is stable and non-slip.

How do I replace the blade assembly?

Unscrew the retaining nut on the shaft end. Remove the old blade and seal, insert the new blade, and tighten the nut securely. Always replace the seal if worn.

Is the Bogen C35 suitable for crushing ice?

It can crush small ice cubes if pulsed quickly. For best results, use the chopper accessory and pulse in short bursts.

What does the turbo boost function do?

The turbo boost temporarily increases the speed to maximum for tough ingredients. Press and hold the turbo button while blending.

Where can I find spare parts?

Spare parts are available from Bogen authorized dealers or online. Use the model number C35 to find compatible parts like blade assemblies and seals.

USER MANUAL C35 Bogen

Classic Series Amplifiers C35, C60, & C100 Models

Installation and Use Manual

Notice: Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change.

WARNING: To reduce the risk of Fire or Electric Shock, Do Not Expose this apparatus to rain or moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

WARNING: Only connect unit to AC mains outlet providing protective earthing connection.

NOTE: Mains plug or an appliance coupler are used as disconnect devices from the mains and shall remain readily accessible and operable.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Always follow these basic safety precautions when installing and using the unit:

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean unit with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade, or the third prong, are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when not used for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY FRONT/BACK COVERS OR PANELS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions.

PANEL DESCRIPTIONS 2-3

Classic Series Front Panel 2

Classic Series Rear Panel ....3

INSTALLATION 4

Package Contents....4

Ventilation 4

Rack Mounting ....4

CONNECTIONS 5

Input Connections....5

Microphone Connections ....5

Auxiliary 5

AUX Muting 5

TEL....5

Output Connections 5

Speakers, General 5

Speakers, Low-Impedance....5

Tape/Booster Connection 5

WMT1A Connection 5

OPERATION 6-7

Front Panel Controls....6

Power 6

Input Volume Controls 6

MIC2, AUX1 Mode Switch 6

Bass and Treble Controls....6

Rear Panel Controls 7

TEL Volume Control 7

VOX Sensitivity Control 7

SPECIFICATIONS 8

TROUBLESHOOTING....9

LIMITED WARRANTY ....10

ACCESSORIES....10

Classic Series Front Panel

1. MIC1 Level Control

Individual level control for a dedicated microphone input.

2. MIC2/AUX1 Mode Switch

Switch selects either the MIC2 or AUX1 connection as the active input.

3. MIC2/AUX1 Level Control

Individual level control for a dedicated microphone input or for an auxiliary input depending on input mode selected.

4. AUX2 Level Control

Individual level control for a dedicated auxiliary input.

5. Treble Control

Controls the amount of cut or boost of treble frequencies above 10 kHz.

6. Bass Control

Controls the amount of cut or boost of bass frequencies below 100 Hz.

7. Power

AC Power switch. Illuminates when ON.

Classic Series Rear Panel

Models C35/60

1. Amplifier Output

Screw terminal strip containing all available speaker outputs.

2. Tape/Booster

RCA unbalanced signal level/output.

3. WMT1A

RCA output connection for Bogen's 600-ohm balanced line matching transformer Model WMT1A.

4. AUX Terminal

Screw terminal connection that allows externally controlled muting of AUX inputs with a contact closure.

5. Microphone Inputs

Screw terminal strip containing the MIC1 and MIC2 balanced, low-impedance inputs.

(MIC2 is switch-selectable.)

6. Auxiliary Inputs

RCA unbalanced, AUX1 and AUX2 high-impedance inputs. (AUX1 is switch-selectable.)

7. TEL Input

Screw terminal input for 600-ohm balanced telephone signal.

8. VOX Sensitivity Control

Variable control for adjusting TEL input signal level trigger point for automatic muting of AUX input.

9. TEL Volume Control

Adjusts the telephone input paging level.

Package Contents

• Classic Series Amplifier
- Instruction Manual

Ventilation

When using a shelf or table mount, the amplifier should stand alone with no equipment on top of it or below it.

Rack Mounting

A rack mount bracket kit (Model RPK50) is available as an accessory. (Not included.)

Input Connections

Microphone Connections

These inputs are for two low-impedance balanced dynamic microphones. Connect cable shield to center screw marked "GND."

Auxiliary

The AUX inputs provide unbalanced RCA inputs for connection to external signal-level equipment.

AUX Muting

For this function, a customer-supplied, normally-open contact closure (switch) must be connected to the AUX2 and MUTE terminals. When the contacts are closed, the AUX2 input will be muted. Typically activated by a switch in a push-to-talk style microphone. AUX 1, if selected, is not mutable by contact closure.

TEL

Connect the telephone line to the two outside terminals and the shield, if used, to the center terminal. TEL input signal will trigger automatic muting of AUX 1 and AUX 2. Input impedance is 600-ohm and is transformer balanced. Input is for "Dry" audio signals only, no DC voltage on the signal.

Output Connections

Speakers, General

The amplifier may be used with most conventional speaker systems. Connect one speaker lead to the screw terminal that corresponds to the impedance of the type of speakers used in the system and the other lead to the COM terminal. If the line is shielded, connect the shield to GND.

Connecting the GND to the COM terminal when using the transformer-coupled outputs references the transformer output to ground. Disconnecting the GND terminal from COM allows the transformer output to float electrically. This is sometimes useful under certain conditions where a ground connection is undesirable. It is generally a good idea to short the GND to the COM terminal regardless of output type (Trans or Direct).

Speakers, Low-Impedance

To connect a 4-ohm speaker, remove the the 4-ohm link and connect the speaker between 4-ohm and GND.

Tape/Booster Connection

To record the amplifier program, connect a patch cord from the TAPE/BOOSTER output jack to the input of a recording device. Can also be connected to the input of a booster amplifier.

WMT1A Connection

This output jack is directly connected to the 25V speaker tap and permits the connection of Bogen's general-purpose matching transformer (WMT1A). The WMT1A steps the signal down by a 5:1 ratio, giving you a 600-ohm balanced signal that can drive long cable runs.

Models C35/60

Model C100

Front Panel Controls

Power

The front panel ON/OFF switch applies power to the amplifier and is illuminated when power is ON.

Input Volume Controls

Each input module may be individually controlled by its corresponding volume control knob.

MIC2, AUX 1 Mode Switch

Activates the corresponding input that it is switched to, MIC2 or AUX1. The other input is inactive and any connections to the inactive input will not work.

Bass and Treble Controls

The Bass and Treble controls are used to adjust the tonal balance of the amplifier output. The center position of these controls provides flat frequency response. Counterclockwise rotation of these controls reduces the bass or treble response, while clockwise rotation increases such response.

The treble control has a cut/boost range of +/- 11 dB at frequencies above 10 kHz and provides a roll off after 20 kHz to reduce gain above the audio range.

The bass control has a cut/boost range of +/- 11 dB at frequencies below 100 Hz. When driving speakers using the direct-coupled output terminals, the bass filter's response is flat to 20 Hz.

Rear Panel Controls

TEL Volume Control

The TEL VOLUME control on the rear panel adjusts the TEL input's paging level. It does not affect the microphone level. Rotate the control counterclockwise to decrease the level. Rotate the control clockwise to increase the level.

VOX Sensitivity Control

When an input signal (such as voice) is detected through the TEL input, the music channels (AUX1 and AUX2) will be muted. The VOX Sensitivity control should be set so that only the desired signal is above the threshold level, while noise and unwanted signal is below it. To adjust the sensitivity of this circuit:

1. Rotate the control fully clockwise. While making a page announcement and talking at a low level, the sound should not be choppy nor missing parts of words. If it is choppy, or if intelligibility is poor, rotate the control counterclockwise to the point where the sound is clear and crisp (but not to the maximum counterclockwise position).
2. If the background music shuts down when no page is in progress, rotate the control clockwise until the music is restored.

Power Output (RMS)

C35: 35W

C60: 60W

C100: 100W

Frequency Response

& Distortion

Transformer†: 70 Hz to 16 kHz (± 2 dB) @ 1% max.

4-Ohm Direct Output: 20 Hz to 20 kHz (± 1 dB) @ 0.5% max.

Hum and Noise

MIC Input: 55 dB below rated output

AUX Input: 70 dB below rated output

TEL Input: 70 dB below rated output

Tone Control Action

Bass: +/- 11 dB @ 100 Hz

Treble: +/- 11 dB @ 10 kHz

Input Sensitivity

MIC Lo-Z Balanced: 600 μV

AUX: 85 mV

TEL: 75 mV

Outputs 8 ohms (C35 & C60 models only), 16 ohms, 25V, and 70V transformer-isolated balanced or unbalanced; 4 ohms direct unbalanced

Output Connections: Speaker screw terminal strip, TAPE/BOOSTER RCA jack; WMT1A RCA jack

Input Connections: (2) MIC Lo-Z screw terminals; (2) AUX Hi-Z RCA jacks, TEL screw terminals

Controls: MIC1, MIC2/AUX1 (switch selected), AUX 2, BASS, TREBLE, TEL, VOX

Thermal Emissions (Full Power)

C35: 119.5 BTU/hr.

C60: 228.8 BTU/hr.

C100: 399.6 BTU/hr.

Power Requirements: 120V AC, 60 Hz

AC Line Draw

C35: 85W

C60: 148W

C100: 220W

Dimensions: 14^1/2 " W x 3^3/4 " H x 11" D (all models)

Product Weight

C35: 15 lb.

C60: 17 lb.

C100: 19 lb.

Approvals: Listed to UL Standard 60065 for U.S. and Canada

PROBLEM	CONDITION	CAUSE
NO SOUND	Power Switch Indicator is OFF.	Amplifier not plugged in.AC outlet dead.Power switch off.Circuit breaker tripped.
	Power Switch Indicator is ON.	No signal from source.Volume turned down.Speakers not connected correctly.Link jumper not set correctly (pg. 5).
DISTORTED SOUND	Power Switch Indicator is ON.Volume Controls are turned up.Unit is extremely hot.Little volume.	Partial short on the output. Check speakers and wires.
	Power Switch Indicator is ON.Volume up. Good volume.	Signal from source is already distorted.Input signal too large for input type (reduce signal level applied to input).Poor speaker connections.Transformer output load on wrong tap.Bass control boosted too much.Output too great for speakers, reduce level.
POOR LOW FREQ. RESPONSE(NO BASS)	Power Switch Indicator is ON.Volume controls are in normal,operational position.	Speakers wired out of phase.Bass control set to cut.Note:Transformer-coupled speakers have less bass response.
NOISE/HUM	Power Switch Indicator is ON.Volume controls are in normal,operational position.	Poor electrical connections at input.Shields of cables not connected.Input cable routed near AC cables, power transformer, or other EMI radiating devices.Electrically noisy devices operating on the same AC circuit.Poor equipment grounding.Ensure that all AC safety grounds are connected.Make sure that all components in audio chain are tied to the same ground.

Limited Warranty; Exclusion of Certain Damages

Bogen Classic Series Amplifiers are warranted to be free from defects in material and workmanship for 2 (two) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period, will be repaired or replaced by Bogen, at Bogen's option, provided the product is shipped insured and prepaid to: Bogen Factory Service Department, 4570 Shelby Air Drive, Suite 11, Memphis TN 38118, USA. Repaired or replacement product will be returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN'S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department – same address as above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's expense. All returns require a Return Authorization number. For most efficient warranty or repair service, please include a description of the failure.

11/2014

Accessories

Two black metal-framed panels with mounting holes, shown from different angles (no text or symbols visible)

RPK50 - Rack Mounting Kit

• Adapts Classic Series amps (Models C35, C60, and C100) for 19" rack mounting, 2 rack spaces (3-1/2")
  • Heavy gauge steel construction

Close-up of a black USB cable with four circular connectors attached to a metallic device (no text or symbols visible)

WMT1A - Matching Transformer

• Hi-Z, 10k-ohm primary impedance
- Lo-Z, 600-ohm secondary impedance, balanced with center tap
- Matches high-impedance unbalanced or low-impedance balanced signals
- Jumper selection allows line level signal to microphone level signal conversion