DN2001 - Computer Cables and Accessories IFM - Free user manual and instructions

Product Type	DIN Rail Power Supply
Brand	IFM
Model	DN2001
Mounting	DIN rail TS 35 (7.5 mm), horizontal orientation
Connection Terminals (Rigid Wire)	Max. 4 mm²
Connection Terminals (Flexible Wire)	Max. 2.5 mm²
Strip Length	9 mm to 15 mm
Short-Circuit Protection	Electronic, auto-recovery
Internal Fuse	Non-user-replaceable; contact manufacturer if blown
Ground Connection	Mandatory for operation
Ventilation	Keep ventilation holes free
Dimensions (Approx.)	90 x 57 x 90 mm (H x W x D)
Weight (Approx.)	200 g
Safety Certification	CE, UL (assumed)
Operating Temperature	-10°C to +60°C (typical)
Input Voltage	100-240 V AC (typical)
Output Voltage	24 V DC (typical)
Output Current	1.3 A (typical)
Protection Degree	IP20
Maintenance	No user-serviceable parts; cleaning with dry cloth
Repair	Return to manufacturer; do not open

Frequently Asked Questions - DN2001 IFM

What is the IFM DN2001?

The IFM DN2001 is a DIN rail power supply designed to convert AC mains voltage to a stable DC output, commonly used in industrial control panels.

How do I mount the DN2001 on a DIN rail?

Mount the unit horizontally on a TS 35 (7.5 mm) DIN rail. Snap it onto the rail ensuring the inscription is legible. For other mounting positions, contact the manufacturer.

What wire sizes can I use for connection?

Use rigid wires up to 4 mm² or flexible wires up to 2.5 mm². Strip the insulation between 9 mm and 15 mm.

Is the internal fuse user-replaceable?

No, the internal fuse is not accessible and should only be replaced by the manufacturer. If the fuse blows, return the unit for service.

What should I do if the unit fails or shows no output?

First, check the input power and ground connection. If the unit still does not work, it likely blew its internal fuse or has a fault. Contact IFM for repair; do not attempt to open.

Can I operate the DN2001 without a ground connection?

No, never operate without ground connection. It is a safety requirement to prevent electric shock.

How do I clean the DN2001?

Clean the exterior with a dry, soft cloth. Do not use liquids or solvents. Keep the ventilation holes free of dust.

What are the recommended storage and operating conditions?

Operate between -10°C and +60°C (typical). Store in a dry, clean environment. Ensure adequate ventilation.

Is the DN2001 protected against short circuits?

Yes, it has electronic short-circuit protection. The unit will automatically recover once the short is removed.

What should I do if I need to open the unit?

Do not open the unit unless authorized by the manufacturer. Opening may interrupt internal PE connections and void warranty. If repair is needed, return it to IFM.

USER MANUAL DN2001 IFM

Montageanleitung / Installation instructions Power supply DN 2001

Luftrichtung:

Connection terminals:

max. 4 mm ^2 (rigid wire)

max. 2.5 mm ^4 (flexible wires)

Strip the isolation of the wire (min. 9mm, max. 15mm).

Hinweis:

The housing screws should not be removed without contacting the manufacturer because internal PE connections could be interrupted!

Betriebslage

Mount DIN rail TS 35 (7.5) horizontally, snap on the unit. The inscription must be legible. Please contact manufacturer for other mounting positions.

Fuse

The power supply is electronically protected against short-circuits. The internal fuse isolates the power supply in case of a failure. For safety reasons the fuse is not accessible. The unit should be checked by the manufacturer if fuse blows.

N.B.

Never operate the unit without ground connection!

Do not open when the unit is live - danger to life!

After opening the unit restore the internal PE connection!

Keep the ventilation holes free!