CA-CD800 - Car radio Fusion - Free user manual and instructions

Product Type	Car Stereo with CD/MP3/WMA/USB/SD/AUX/iPod/iPhone/Bluetooth
Power Supply	12V DC (11-16V), Negative Ground
Fuse	15A
Speaker Impedance	4-8 ohms
Power Output (Max)	MOSFET 4 x 50W
RMS Power Output	22W x 4 @ 10% THD
Pre-amp Output	5.0V (USB play mode; 1kHz, 0dB, 10kΩ load)
Subwoofer Output	5.0V (USB play mode; 61kHz, 0dB, 10kΩ load)
DAC	1-Bit
iPod/iPhone Charging	USB, 1A
Radio Bands	FM (3 bands), AM (2 bands), with RDS
Bluetooth	Version 2.0, Class 2, A2DP, HFP, range ~3m
Supported Media	CD, CD-R/RW, MP3/WMA discs, USB (2.0), SD card, AUX In (3.5mm)
File Systems	FAT32 (USB/SD), ISO9660 Level 1/2, Joliet
Display	LCD with 32K+ RGB variable color (customizable)
Equalizer Presets	FLAT, POP, USER, DANCE, ROCK, CLASSIC, JAZZ, VOCAL
Audio Functions	Bass/Mid/Treble with Center Frequency adjustment, EBX bass boost, Balance, Fader, Subwoofer control
Detachable Face	Yes, with security storage case
Steering Wheel Control Ready	Yes (3.5mm jack, aftermarket interface required)
Remote Control Option	CA-REM1 IR remote (optional)
Weight	Approximately 1.5 kg (estimated)
Dimensions (Approx.)	Standard 1-DIN (178 x 50 x 160 mm)

Frequently Asked Questions - CA-CD800 Fusion

How do I pair my phone via Bluetooth with the Fusion CA-CD800?

Enable Bluetooth on your phone, search for new devices, select 'FUSION' from the list. If prompted for a PIN, enter 0000. Once paired, the unit will automatically connect on future use.

How can I reset the unit to factory settings?

Locate the RESET button on the main unit (small hole). Use a ballpoint pen or similar object to press it. This resets all settings to default and can resolve freezing or error messages.

What should I do if the display shows 'ERR-1'?

'ERR-1' indicates the USB or SD device cannot be read. Ensure the device is formatted to FAT32 (Windows) file system and contains only MP3 or WMA files.

Can I control my iPod/iPhone directly from the device?

Yes. Connect your iPod/iPhone via the front or rear USB using an Apple data sync cable. Press the iPod/iPhone Internal/External Control button to switch between control from the head unit or the device itself.

How do I set the clock on the CA-CD800?

Press MENU and navigate to 'CLK' setting. Rotate the encoder to set hours, press to confirm, then set minutes. You can also toggle 12H/24H format in the system menu.

Why is there no sound or power?

Check that the ignition is on, the unit is powered on, and the fuse is intact. Verify speaker connections. If using an amplifier, ensure it is functioning. If all else fails, press the RESET button.

How do I change the display color?

Press and hold the ESC/END/RGB button to enter the 32K+ RGB color menu. Rotate the encoder to select a preset color or choose 'USER' to create a custom color by adjusting Red, Green, and Blue levels.

Can I use the auxiliary input for external devices?

Yes, the unit has a 3.5mm AUX IN jack on the front panel. Connect your device using a 3.5mm stereo cable and select 'AUX' as the source by pressing the SOURCE button.

What file formats are supported for USB/SD playback?

The unit supports MP3 (MPEG1/2/2.5 Layer 2/3) and WMA (Version 7/8/9) files. Sampling rates vary; bit rates from 32 to 320 kbps and VBR are supported. Maximum file/directory count is 999.

How do I store and recall radio presets?

Tune to the desired station, then press and hold one of the numbered preset buttons (1-6) for 2 seconds until 'SAVED' appears. To recall, simply press the corresponding preset button while in the same band (FM1/2/3 or AM1/2).

USER MANUAL CA-CD800 Fusion

MADE FOR:

iPhone 45 16GB 32GB 64GB

iPod touch 4th generation 8GB 32GB 64GB

IPod nano 6th generation 8GB 16GB

iPhone 4 16GB 32GB

iPod touch 3rd generation 32GB 64GB

iPod nano 5th generation (video camera) 8GB 16GB

iPhone 3GS 8GB 16GB 32GB

iPod touch 2nd generation 8GB 16GB 32GB

iPod classic

For the latest news on supported iPod models visit: www.fusionelectronics.com

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference,
AND
- This device must accept any interference received, including interference that may cause undesired operation.

CONTENTS

Precautions & Maintenance P3

Quick Start Guide P3

Dashboard Installation P4

Connecting the System P5

Removal / Re-Attachment of the Face P6

Basic Operations P6 Audio Functions P8

System Menu P9

Radio Operation P10

RDS Operation P10

iPod / iPhone Operation P11

Bluetooth H/F & A2DP Operation P13

Media Playback (CD/USB/SD/Aux In) P15

Additional Media Playback Functions P16

Steering Wheel Control Interface Ready P17

Optional Remote Control P18

Troubleshooting P18

How To Reset The Unit P19

RDS Program Types & Descriptions P20

Product Specifications P20

Supported File Types P21

Licensing P21

Register Your Product Online P21

Warranty P22-29

Notes P30-31

PRECAUTIONS & MAINTENANCE

GENERAL

• When cleaning the vehicle, do not get water or cleaning fluids on the unit.
• Do not attempt to open the unit chassis. There are no user servicable parts or adjustments inside.
• This unit has been tested with all compatible authentic iPod/iPhone models under normal expected operating conditions, free from any pre-existing defects in either the unit or iPod/iPhone and with unmodified or "jailbroken" software.
• No Responsibility can be taken for use of the unit other than under normally expected operating conditions in conjunction with fully functional and undamaged iPod/iPhone units which have been manufactured and authorised by Apple Inc.
• Ensure that only a Genuine USB data sync iPhone/iPod cable is used for connection to this unit.
• When the vehicle's air conditioner is in use, moisture may accumulate on the CD Laser lens. This may cause disc read errors. If this occurs, remove the disc and wait for the moisture to evaporate.

QUICK START GUIDE

When the unit is powered up for the first time (or the battery is disconnected or runs flat), you will need to set your tuner region.

1. When you press the power button to turn on the unit, ① [OCEANIA] will be displayed on the LCD screen as the default Tuner region.
2. Rotate the Encoder Volume Control to select an option: OCEANIA (Australia / New Zealand), USA, EUROPE or RUSSIA.
3. Press the Encoder Volume Control to store your selection and exit to the Tuner mode.

If you make the wrong selection, you may not be able to tune in to your desired stations. This setting can be easily changed from the SYSTEM MENU - see page 9

SELECTING THE MUSIC SOURCE

Press the source button S to cycle through the following sources

(if available) - Radio→ CD→ FRT USB→ REAR USB→ SD→ BT AUDIO→ AUX

BLUETOOTH PAIRING

1. Ensure Bluetooth is enabled on the phone to be connected to the unit.

2. Search for a new Bluetooth device on the phone.

3. Select "FUSION" on the Bluetooth device list.

4. Some devices may require you to enter a PIN.

If prompted, enter "0000" for the PIN.

Please see P12 for detailed Bluetooth operation.

RGB 32K+ SELECTION

The initial colour setting for this unit is Colour Scan. To quickly enter the 32K+ RGB colour menu, press and hold the ESC/END/RGB button

You can then rotate the Encoder Volume Control to select from the following pre-set display colours:

WHITE: GREEN1: GREEN2: GREEN3: AMBER: PINK1: PINK2: PURPLE1: PURPLE2: BLUE1: BLUE2: USER COLOUR: ORANGE

Press the ESC/END/RGB button button your selection.

See Page 10 for details on how to set the USER COLOUR

STORE DEMO MODE

When you connect the unit for the first time and press the Mute/Power button Ⓧ the unit will operate in Demo Mode. To exit Demo Mode, press the Mute/Power Button again. See Page 10 to turn Demo Mode off.

DASHBOARD INSTALLATION

The following illustration shows a typical installation.

If you have any questions or require information regarding installation kits, consult your car audio retailer.

If you are not sure how to install this unit correctly, have it installed by a qualified installer.

CONNECTING THE SYSTEM

Figure 2

ISO CONNECTOR WIRING DIAGRAM

P/N	WIRE COLOR	FUNCTION/LABEL
A4	YELLOW	12V CONSTANT(+)
A5	BLUE	CONNECT TO SYSTEM CONTROL TERMINAL OF THE POWER AMP OR AUTO ANTENNA RELAYCONTROL TERMINAL(max 150mA 12VDC)
A6	ORANGE/WHITE	DIMMER
A7	RED	12V ACCESSORIES (+)
A8	BLACK	GROUND
B1	VIOLET	RIGHT REAR SPEAKER(+)
B2	VIOLET/BLACK	RIGHT REAR SPEAKER(-)
B3	GREY	RIGHT FRONT SPEAKER(+)
B4	GREY/BLACK	RIGHT FRONT SPEAKER(-)
B5	WHITE	LEFT FRONT SPEAKER(+)
B6	WHITE/BLACK	LEFT FRONT SPEAKER(-)
B7	GREEN	LEFT REAR SPEAKER(+)
B8	GREEN/BLACK	LEFT REAR SPEAKER(-)

REMOVAL/RE-ATTACHMENT OF THE FACE

1. Press the Panel OPEN button.
2. After flipping down the front panel, push it to the right (A), then draw the left of the front panel outwards (B)
3. To re-attach the face, please complete the above steps in reverse

PLEASE NOTE

• If any function does not work, open the front panel & re-close.
• Do not touch the contact pins on the rear of the face as this could cause contact problems. If the contacts become dirty, please clean with a soft cloth.
• Petrol and other solvents must not come in contact with the front face
• Please use the supplied plastic case to store the front face when it is removed from the unit.
• For security purposes, please ensure that when removed, the face is stored out of sight if left in the vehicle.

BASIC OPERATIONS

1. OPEN

Press this button to flip open and detach the control panel.

2. ENCODER VOLUME CONTROL

Rotate the encoder volume to increase and decrease the volume.

1. iPod/iPhone INTERNAL/EXTERNAL CONTROL

Press this button to switch between iPod/iPhone control from either the unit or from the device itself.

4. ENCODER VOLUME CONTROL AUDIO/ENTER FUNCTIONS

a) AUDIO. Press this button to enter the Audio Menu mode.

b) ENTER. In Media playback mode and Menu functions, press this button to confirm a selection (ENTER).

1. MUTE - POWER ON/OFF Ⓡ①

a) Press this button to turn Mute ON or OFF

b) Press this button to turn the unit on. Press and hold to turn the unit off.

1. ANSWER KEY

In Bluetooth Handsfree mode:

a) Press this button to answer an incoming call.

b) Press & hold for 2 seconds to transfer the call from the CA-CD800 back to the Mobile Phone.

7. NUMERIC BUTTONS

a) In the Tuner mode, press the Numeric buttons to recall the preset stations. Press and hold these buttons for 2 seconds to store stations.

b) In Media playback mode, Press the Numeric buttons to perform the operations below:

Number	1	2	3	45	6
Button	Pause/Play	ntro Repeat	Random Folder	Up Folder	Down

8. SUBWOOFER - DIRECT SUBWOOFER LEVEL CONTROL

When a subwoofer is connected; use the DSLC buttons to adjust the subwoofer level up or down.

9. EQ/DISPLAY |||

a) EQ. Press this button to select the preset equaliser settings: FLAT->POP->USER->DANCE->ROCK->CLASSIC->JAZZ->VOCAL

b) DISP. Press & hold for 2 seconds.

- In MP3/WMA playback mode, press to display ID3 information: Track number and elapsed play Time - → File - → Album - → Title - → Artist, - In iPod/iPhone playback mode, press to display Album -→ Title -→ Artist

10. ESC/END/RGB

a) ESC - ESCAPE. Press to quick return previous menu or mode rather than having to cycle through all of the options in the menu. b) END - In Bluetooth Handsfree mode, press to END a call or to Reject an incoming call (before you answer).

c) RGB - 32K+ RGB COLOUR. Press and hold this button to access the 32k+ variable colour setting mode. See Page 9 for more information

11. BAND/SEARCH

a) In Tuner mode, press this button to cycle through Bands: FM1, FM2, FM3, AM1 [MW1] or AM2 [MW2].
b) In Media playback mode, press to access the folder / file search mode.
c) In iPod/iPhone playback mode, press this button to access the iPod/iPhone search functions.

12. MENU

Press to access the system menu. See Page 9 for menu options.

13. TUNE UP/DOWN, FILE & TRACK UP/DOWN

& FAST FORWARD/BACK

a) TUNE UP/DOWN. In tuner mode, press this button to Auto Seek to the next station or press and hold this button to manually tune in to your desired station. b) FILE & TRACK UP/DOWN. In CD or USB/SD media playback mode, press these buttons to skip a chapter, track or file. c) FAST FORWARD/BACK. In USB/SD media playback mode, press and hold momentarily to fast forward/rewind.

14. SOURCE S

Press the SOURCE button ☑ to cycle through the following sources (if available): Radio→CD→FRT USB→REAR USB→SD→BT AUDIO→AUX

AUDIO FUNCTIONS

All Audio functions are easily accessible on the CA-CD800.

AUDIO MENU. Press the ENCODER VOLUME CONTROL to access the Audio Menu mode. Then press ENTER or TUNE UP >>| to select the Audio Function to be adjusted, then rotate the ENCODER VOLUME CONTROL to select the desired setting. You can always return to the previous Audio Function by pressing the TUNE DOWN |<< button.

REMINDER

In the AUDIO MENU, or in any menu, you can quickly exit the menu by pressing the ESC/END/RGB button

QUASI-PARAMETRIC FUNCTION - CFQ ADJUSTMENT

As part of the available Audio Functions, you have the ability to adjust the Center Frequency of the Bass, Midrange or Treble controls. This gives you greater control of the adjustment of these functions by allowing you to select the preferred Center Frequency to adjust.

If you are unsure of which CFQ settings to use, please use the following Default settings: Bass CFQ 80Hz, Midrange CFQ 1.5K Hz & Treble CFQ 12.5K Hz

AUDIO FUNCTION ADJUSTMENT:

EBX ON/OFF: Turn ON or OFF the EBX (Encounter Bass Xtender) Bass Boost.

BAS Adjust the Bass level between -7 to +7.

BAS CFQ Select Bass centre frequency: 60 / 80 / 100 / 200Hz

MID Adjust the Midrange level between -7 to +7.

MID CFQ Select the Midrange centre frequency: 0.5K / 1.0K / 1.5K / 2.5KHz

TRE Adjust the Treble level between -7 to +7.

TRE CFQ Select the Treble centre frequency: 10.0K / 12.5K / 15.0K / 17.5KHz

BAL (Balance) Adjust the balance between the right and left speakers from 12R (full right) to 12L (full left).

FAD (Fader) Adjust the fader between the front and rear speakers from 12R (full rear) to 12L (full front).

(SUBWOOFER)

SW ON/OFF Turn On or Off the Subwoofer RCA output.

SW LPF Subwoofer low pass crossover: 80/120/160Hz

SWAM ON/OFF In AM mode, turn ON or OFF the Sub output.

NOTE

If the Subwoofer RCA output is set to "OFF", then the SW LPF & SWAM functions will not be displayed in the Audio Menu.

EQUALISER OPERATION

When you activate the Equaliser, the Pre-Set Equaliser settings override your existing Bass, Midrange & Treble Settings.

Press the Equaliser button repeatedly to cycle through the following pre-sets: FLAT-->POP-->USER-->DANCE-->ROCK-->CLASSIC-->JAZZ-->VOCAL

To return to the Bass/Midrange/Treble settings that were in use before the EQ was selected, please select the USER setting.

SYSTEM MENU

Press ☐(MENU) to access the System Menu and press again to select the item be adjusted, then rotate Encoder Volume Knob to select a value / option. To exit this menu at any time, press the ESC/END/RGB button

STORE (Auto store)

While in Tuner mode, press the ENCODER VOLUME CONTROL to activate Auto Store. The six strongest stations of the selected band will be saved in the preset channels automatically

RDS ON/OFF

While in Tuner mode, this selection turns On or Off RDS. RDS Functions are explained in more detail on Page 10. If RDS is set to OFF, then the RDS Functions indicated below with an * will not appear in the System Menu

PTY* (Program Type)

Press the ENCODER VOLUME CONTROL to enter program type, then rotate the ENCODER VOLUME CONTROL to select the category.

AF* ON/OFF

Turn On or Off the Alternate Frequencies function.

TA* ON/OFF

Turn On or Off the Traffic Announcement function.

REG* ON/OFF

Turn On or Off the Set Region for Alternate Frequencies function

CT* ON/OFF

Turn On or Off the CT function.

LOC* ON/OFF

(Local/Distance). Use this setting to Auto Seek to strong local stations (Local) or all stations regardless of their strength (Distance).

AREA

Select your country/region for the tuner: OCEANIA (Australia/New Zealand); USA; EUROPE; RUSSIA & press ESC/END/RGB ESC to save.

CLK (Clock)

To set the clock, rotate the Encoder Volume Control to set the hours (Note "A" or "P" will be displayed in the top-right hand of the LCD display indicating AM or PM if the Clock is in 12H mode – see below). Press the Encoder Volume control to select "minutes" then rotate the control to set.

CLK 12H/24H (Clock Format)

Select the time format 12H or 24H

BEEP ON/OFF

Select On or Off to activate button confirmation beep tones.

DEMO ON/OFF

Demo mode is activated when the unit is first connected to the vehicle, but is de-activated when the Power Button is pressed. It can, however, be activated again by pressing the Power Button. To stop this feature, set Demo Mode to off.

COLOUR

This unit is equipped with a 32K+ RGB variable colour display. By rotating the Encoder Volume Control, you can select the system colour from the following options:

COLOUR SCAN (default setting); WHITE; GREEN 1; GREEN 2; GREEN 3; AMBER; PINK 1; PINK 2; PURPLE 1; PURPLE 2; BLUE 1; BLUE 2; USER; DEFAULT.

USER (USER SELECTED COLOUR):

This allows you to select your choice of display colour from over 32,000 combinations (32K+). When you select USER in the colour menu, press the Encoder Volume Control to enter then rotate to select the intensity of Red, Green & Blue (from between 0 and 32) to make your own custom colour.

To switch between R (Red), G (Green) and B (Blue) setting modes, push the TUNE UP button >>|

Press ESC/END/RGB 📊 button once you have completed your selection.

RADIO OPERATION

TUNE INTO A RADIO STATION

1. Press the SOURCE button 📋 repeatedly until [RADIO] is displayed on the LCD screen.
2. Select your preferred listening Band (FM or AM) by pressing BAND 📋. There are 3 FM Bands [FM1] [FM2] [FM3] and 2 AM Bands [AM1] [AM2]. These multiple Bands allow you to store up to 18 FM stations & 12 AM stations in memory (see below).
3. To search for a radio station, press either the TUNE UP or DOWN >>1/1<< buttons to search for the next station higher than the current station frequency or lower than the current frequency.
4. To Manually tune to a radio station, press and hold either the TUNE UP or DOWN >>1/1<< button until the tuner frequency on the LCD display starts flashing. You can then release the TUNE

UP or DOWN button, and press it again repeatedly until you select your desired frequency. After 5 seconds, the display will stop flashing and the unit will be tuned in to that station.

HOW TO STORE YOUR FAVOURITE STATIONS

1. Select your preferred Band. Generally you would use FM1 or AM1 to save your favourite stations (6 stations per band). If you need to store more stations, you can use FM2/3 or AM2 for AM stations.
2. Tune in to your preferred station as per the steps above
3. Press and hold one of the Preset Station Buttons (1-6) for 2 seconds to store the station. The preset number and [SAVED] will be displayed on the LCD screen.

TUNE TO A SAVED or PRE-SET STATION

1. Select the relevant BAND
2. Press the Preset Station Number corresponding to your required Pre-Set station.

RDS OPERATION

The RDS (Radio Data System) function operates only in areas with FM stations broadcasting RDS signals. If you tune to an RDS station, an RDS icon and information about the presenter, station or program is displayed.

This unit supports the following RDS features:

(PTY) SELECT PROGRAM TYPE

Before tuning to RDS stations, you can select program type and let the unit search only for programs of the selected category. Press the MENU button to enter the System Menu, press ENTER again to confirm and select PTY type & search for that style station. Please see a list of PTY Types & descriptions on P20:

(AF) SELECT ALTERNATE FREQUENCIES

If the radio signal from the current station is poor, you can turn on the AF (Alternate Frequency) function to let the unit search automatically for another station with a stronger signal but with the same program identification as the current station.

(TA) RECEIVE TRAFFIC ANNOUNCEMENTS

If you do not want to miss a traffic announcement during music playback, you can turn on the TA (Traffic Announcement) function.

TA ON: When there is a traffic announcement; the unit switches to the tuner mode (regardless of the current mode) and begins to broadcast the announcement on traffic conditions. When the traffic announcement is over, the unit will return to the previous mode.

TA OFF Traffic announcement does not cut in.

(REG) REGION FOR AF TUNING

REG ON: Only stations in the current region will be tuned to automatically.

REG OFF: All stations can be tuned to automatically

(CT) CLOCK TIME

Turn CT on to set the clock time using RDS data. Turn CT off to set the clock time manually.

This unit is equipped with iPod/iPhone control which allows you to directly control and charge iPod/iPhones using the units controls – with display of iPod/iPhone track information appearing on the unit's LCD display.

Please read below for more detailed operation.

CONNECTING AN iPod OR iPhone

Insert the iPod/iPhone data sync cable to the Front USB or Rear USB socket as shown and the unit will start playing the iPod/iPhone automatically.

The Rear USB connection is ideal for positioning in a location such as the glove compartment so your iPod/ iPhone can be stored and charged securely out of sight.

NOTE

Only one iPhone or iPod can be connected to the CA-CD800 at one time. This means, for example, that if you have an iPod connected to the Rear USB, then the Front USB must be used for a USB storage device & vice-versa.

BASIC SEARCH - PLAYLIST/ARTIST/ALBUM/SONG on iPod/iPhone

Press BAND 🔔 to browse the iPod/iPhone menu.

Then rotate the Encoder Volume Control clockwise to and press ENTER to choose one of the following selections, then follow the steps below:

PLAYLIST Rotate the Encoder Volume control to select your desired Playlist and press ENTER to start play.

ARTIST Rotate the Encoder Volume Control to select your desired Artist then press ENTER. Rotate the Encoder Volume Control to then select an Album & press ENTER. Rotate the Encoder Volume Control again to select a song within the selected Album.

ALBUM Rotate the Encoder Volume Control to select your desired Album and press ENTER to select it. Then rotate the Encoder Volume Control to select a specific song within the selected Album.

SEARCH FOR FURTHER CONTENT on iPod/iPhone

In addition to the PLAYLIST/ARTIST/ALBUM seach functions, there are also additional fields you can search on your iPod or iPhone - the full list of fields is as follows:

PLAYLIST / ARTIST / ALBUM / SONG / GENRE / COMPOSER / AUDIOBOOK / PODCAST

1. Rotate the Encoder Volume knob to select the desired search field, then press ENTER to confirm.

2. Rotate the Encoder Volume knob to select the desired selection within the field then, press ENTER to confirm.

NOTE

When searching for Album, Artist, Song etc, rotate the Encoder Volume Control clockwise to search from A-Z or anti-clockwise for Z-A search.

RANDOM PLAY

Press RDM to cycle between the following modes:

RDM FLD - Plays the current album randomly.

RDM ALL – Plays the whole iPod/iPhone library randomly.

RDM OFF - Turns the Random function off.

iPod/iPhone MASTER CONTROL MODE

Press the 🔊 button to switch between the two control options

• Unit control mode: Use the head unit controls to select Track/Artist/Album/Playlist etc. This is the Default setting.
• iPod/iPhone control mode: Use the iPod/iPhone to select the Artist/Album/Track etc.

This mode is useful if you need to sort through a large amount of Tracks/Albums etc.

NOTE

Please ensure the iPod/iPhone cable is connected correctly to the USB port and only use an original iPod / iPhone data sync cable.

BLUETOOTH HANDS

FREE & A2DP

STREAMING OPERATION

You can make or receive phone calls with Bluetooth enabled phones and listen to music from an A2DP Bluetooth enabled device on the CA-CD800.

PAIRING A BLUETOOTH DEVICE

When connecting a Bluetooth device for the first time, you will need to pair the device with the unit.

For most devices, pairing only needs to be done once. Please follow these steps:

1. Ensure Bluetooth is enabled on the phone to be connected to the unit.
2. Search for a new Bluetooth device on the phone (this may take up to 30 seconds)
3. Select "FUSION" on the Bluetooth device list.
4. Some devices may require you to enter a PIN. If prompted, enter "0000" for the PIN.
5. [PAIRING OK] will be displayed on the LCD display if pairing is successful. The paired device will then connect to the CA-CD800 Automatically.

Note on some phones, you may need to select "SET AS AUTHORISED" or similar to ensure the CA-CD800 will automatically pair on subsequent usage.

PAIRED NOTIFICATION DISPLAY

When the Bluetooth device is paired with the CA-CD800, the Bluetooth Icon ➕ will appear on the LCD display. This should occur whenever you use the system and the paired device is in range.

HOW TO MAKE A CALL

1. Dial the desired number on the Mobile Phone.
2. Once dialling is in progress, [CALLING] will be displayed on the LCD screen.
3. When the call is in progress, [TALK] will be displayed on the LCD along with the elapsed call time.
4. The ANSWER 📋 button will also slowly flash to indicate you are in a call.

RECEIVING A CALL

1. If there is an incoming call, audio playback from the current Source will either be Muted or Paused (depending on the source) and [PHONE IN] will be shown on the Display along with the Caller ID if it is enabled by the Phone/Carrier.
2. Press the ANSWER button to accept the call.
3. To Reject the call, press the ESC/END/RGB button and it will not be answered.

HOW TO END A CALL

Once in a call, press the ESC/END/RGB 📊 button to end the call.

TO REDIAL A NUMBER

1. During normal head unit operation, press the ANSWER button to call the last number dialled by the paired mobile phone. [REDIAL] will be displayed on the LCD screen.
2. To confirm press either the ANSWER button again or ENTER on the Encoder Volume Control. [CALLING] will be displayed on the LCD screen.

HEAD UNIT / HANDSET CALL TRANSFER

You can transfer the call from the car speakers/head unit back to the phone during a call by pressing the ANSWER button for 2 seconds. [TRANSFER] will be displayed on the LCD display.

Press the ANSWER 📋 button again for 2 seconds to transfer the call back to the head unit.

BLUETOOTH A2DP AUDIO STREAMING

If the connected Bluetooth device supports Advanced Audio Distribution Profile (A2DP), you can listen to music stored on the device through the head unit.

BASIC OPERATION

1. Ensure the Bluetooth device is paired with the head unit.
2. Press the SOURCE button 📄 repeatedly to select the BT AUDIO source.
3. Open the music player on the device and select & play your desired track(s)

ADVANCED OPERATION

If the device also supports Audio Video Remote Control Profile (AVRCP), you can control basic playback functions (eg iPod music) via the head unit.
1. Follow steps 1 & 2 above as per Basic Operation
2. Press ▶/11 to start playback. Press again to pause.
3. Press either I/I to advance to the next track, or return to the beginning of the track.
4. Depending on the device, volume adjustment may be possible from the device. Please ensure it is not set too high to avoid distortion.

NOTE

ID3 type information – Title, Artist, Album etc is not available on the LCD screen in Bluetooth A2DP mode.

DISCONNECTING THE BLUETOOTH DEVICE

1. If the Bluetooth device is paired and you want to disconnect it from the CA-CD800, press MENU to enter the System Menu. Keep pressing until [DISCONN>] is displayed.
2. Press ENTER on the Encoder Volume Control. [WAITING] will be displayed on the LCD display, followed by [DISCONNECTED] when completed.

RE-CONNECTING THE BLUETOOTH DEVICE

Once paired, the phone should re-connect automatically every time you use the system. If not, or you have previously Disconnected the phone, you can manually re-connect it using the following steps.

1. Press MENU to enter the system menu. Keep pressing until [CONNECT>] is displayed.
2. Press ENTER on the Encoder Volume Control. [WAITING] will be displayed on the LCD display, followed by [CONNECTED] when completed.

MEDIA PLAYBACK (CD/USB/SD/AUX IN)

CD PLAYBACK

You can play the following format CD's

• Commercially Available pre-recorded CD's
• CD Recordable (CD-R)
• CD Re-writeable (CD-RW)
- MP3 CD's
• WMA CD's

NOTE: Please ensure that the disc contains these file types only.

1. Press OPEN on the front panel to open the flip down panel.
2. Insert a CD with the printed side facing up, then close the panel. The CD will start playing automatically.
3. Press ▶/11 to pause the music playback. Press this button again to resume music playback. NOTE the volume level can be adjusted while the unit is paused
4. Press the >>1/1<< to skip forward to the beginning of the next or previous chapter/track.
5. Press and hold >>1/ltcc fast forward or fast rewind through the track.
6. Press ▲ to eject the CD.

USB OPERATION

Insert the USB Device

1. Open the cover marked ↩ on the front panel.
2. Insert the USB device into the USB socket. The unit will start playing from the USB device automatically.
3. USB storage devices can be used in the Front, Rear USB port of both.

Removal of the USB Device

Before removing the USB device, always remember to switch to another Source then remove the USB device.

SD CARD OPERATION

Insert the SD Card

1. Press the OPEN button on the front face.
2. After flipping down the front face, push it to the right then draw the left of the face outwards to remove it.

1. Insert the SD card into the slot with label facing up until a "CLICK" sound is heard.
2. Replace the front panel and the unit will start playing files from the card automatically.

Removal of the SD Card

Detach the face and press the card until you hear a click sound. The card is now disengaged. You can then remove the card.

NOTE

Please ensure that USB devices & SD cards contain WMA or MP3 files only.

USING AUX-IN

Connect the external device to AUX in jack using a 3.5mm stereo Aux In cable (not supplied) located on the face, then press the Source button to select AUX mode.

Press the Source Button again to select other source options.

ADDITIONAL MEDIA PLAYBACK FUNCTIONS (CD/USB/SD)

PLAY OPTIONS

MP3/WMA File or Folder Search

• Press the BAND 📞 button on front panel access the MP3/WMA file search mode.
• Rotate the Encoder Volume Control to search through all folders on the device then press ENTER to make your selection.
• Rotate the Encoder Volume Control to select the desired track within the previously selected folder and press ENTER to start it playing

INTRO PLAY

• During playback, press the INT button (Preset button 2) to start intro mode. The first 10 seconds of all tracks on the storage media will be played.
• Once you have found a track you like, press INT again to resume normal playback.
• To perform Intro Play on files in the current folder only, press & hold the INT button while in Intro Mode. [INT] will be displayed on the LCD along with the folder number. When you find your desired track, press INT Twice to play the track normally.

REPEAT PLAY

- During playback, press the RPT button (Preset button

3) to repeat all tracks on the storage media. [RPT ALL] is displayed.

• If you press RPT again, the current track will be repeated only [RPT TRK] will be displayed
• Pressing RPT again repeats all tracks in the current folder only [RPT FLD] is displayed
• Once a track is playing in repeat mode, or to check if Repeat is on, press the RPT button.
• To Cancel Repeat, press and hold the RPT button. The display will revert back to the standard track number & time elapsed display.

RANDOM PLAY

• During playback, press the RDM button (Preset button 4) to display the current Random Play Mode. If Random Play is off, [RDM OFF] will be displayed.
• Press RDM again to select Random Play for the current folder only [RDM FLD] is displayed.
• Pressing RDM again selects Random Play for all tracks on the storage media [RDM ALL] is displayed.
• To cancel Random Play, press RDM to display the current Random Play mode, then press RDM again to cancel Random Play

FOLDER SELECT

During music playback, use this button to jump to the previous/next folder on the storage device.

DISPLAY FUNCTION

During playback, pressing the DISP button will automatically cycle through the following information on the file being played on the LCD display:

FOLDER NAME→ FILE NAME→ ALBUM→ TITLE→ ARTIST

You can also keep pressing the DISP button to find the particular information you are after. Once you have cycled through all of the available track information by continuing to press the DISP button, the display will return to the standard Track Number & Time display. If you stop at this point, the Automatic Display function is cancelled.

STEERING WHEEL CONTROL INTERFACE READY

This unit includes a 3.5mm Steering Wheel Control interface. When used in conjunction with an after market Steering Wheel Control Interface, you can control some functions of this unit with the Vehicle's OEM Steering Wheel Controls.

There is even a provision to adjust the Direct Subwoofer Level Control if the vehicle has Preset Up/Preset Down controls.

Control Functions (if available on vehicle):

VEHICLE CA-CD800

Mode Source

Vol Up Volume Up

Vol Down Volume Down

Track Up Track Up

Track Down Track Down

Preset Down Sub Level Down

Preset Up Sub Level Up

Please visit www.fusionelectronics.com to check for available interfaces as they become available.

OPTIONAL REMOTE CONTROL

The CA-REM1 IR Remote Control is available to suit this unit.

Please consult you Car Audio retailer for pricing and availability.

TROUBLESHOOTING

Before going through the check list, please check the wiring connection diagram. If problems persist, please consult your Car Audio dealer.

No power or no sound

• Ignition is not on. Turn the Ignition to "accessories"
• Unit is off - press the power button to activate the unit.
• Fuse is blown. Please replace the fuse.
• If the speakers are connected to the speaker outputs, check the speaker connections.
• If the speakers are connected to amplifier/s only, check that they are operating correctly.
• If the above solutions do not help, please press the RESET button.

Noise in radio broadcasts

• Signals are too weak, turn LOC off.
- Check the antenna connection or replace the antenna if necessary.

Preset stations lost

- Yellow power cable is not correctly wired. Ensure it is connected to Constant 12V (+).

Unable to Eject Disc

- Press & hold the Eject button ▲.

Display shows ERR-1

- The USB or SD device cannot be read. Confirm the device is formatted to FAT32 (Windows) file system.

Display shows ERR-3

- USB/SD data error. Check to ensure only MP3 or WMA files are loaded on the storage devices.

Display shows ERR-5

- Communication error. The USB/SD device could be damaged or corrupted. Please re-format (Fat32 only) or try a different device.

Bluetooth

• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect with this head unit.
• As Bluetooth is a wireless communication protocol, there may be times where connection between the device and head unit is lost or disrupted due to interference or other signal quality disruptions.
• A2DP playback may be interrupted or playback speed may vary, or playback may not resume automatically after making or receiving a call.
• Some Bluetooth enabled mobile phones may only stream music data. In this case the resultant playback quality through the head unit will be low.
  • Music or noise may be heard for a moment if music streaming is taking place when starting and ending the call,
• There may be occurrences where music cannot be played through the head unit even though music is being played back on the mobile phone.

HOW TO RESET THE UNIT

Using the Reset button, you can reset the unit to its default settings.

• The RESET button is located on the main unit (as shown on the diagram). Press it in with a ballpoint pen or metal object to activate it.

• The reset button can be used under the following circumstances:

• Initial installation of the unit when all wiring is completed.

• If the unit "freezes".
• To RESET the unit to the factory configuration
• Error indication on the LCD display.

RDS PROGRAM TYPES & DESCRIPTIONS

NEWS News services

AFFAIRS Politics & current affairs

INFO Special information programs

SPORT Sports

EDUCATE Education and advanced training

DRAMA Radio plays and literature

CULTURE Culture, religion and society.

SCIENCE Science programming

VARIED Entertainment programs

POP M Pop music

ROCK M Rock Music

EASY M Easy listening music

LIGHT M Light classical music

CLASSICS Calssical music

OTHER M Special music programs

WEATHER Weather information

FINANCE Finance programs

CHILDREN Children's programs

SOCIAL Social affairs

RELIGION Religion

PHONE IN Talkback

TRAVEL Travel programs

LEISURE Leisure

JAZZ M Jazz music

COUNTRY Country music

NATION M National music

OLDIES M Old time music

FOLK M Folk music

DOCUMENT Documentary

A-TEST Alarm Test

ALARM Alarm function

PRODUCT SPECIFICATIONS

Power Supply 12V DC (11-16V), Negative Ground

Fuse 15A

Suitable Speaker 4-80

Impedance

Power output MOSFET 50W MAX x 4 channels

RMS output 22W x 4 @ 10% THD

Pre-AMP output 5.0 V (USB play mode; 1KHZ, 0dB, 10 k Ω load)

Aux-In level ≥300mV

Subwoofer output 5.0 V (USB play mode; 61KHZ, 0dB, 10 k Ω load)

DAC 1-Bit

iPod/iPhone

Charging USB, 1A

RADIO

-FM

Frequency Range 87.5 - 108MHz, 50kHz Step (Oceania)

87.5 - 107.9 MHz 200kHz Step (USA)

87.5 - 108.0 MHz 50kHz Step (Europe)

87.5 - 108 MHz (FM 1/2) (Russia)

+ 65MHz - 74MHz (FM3) (Russia)

Usable Sensitivity Better than 15dB at S/N 30dB

-AM(MW)

Frequency Range 522-1620KHz (Oceania)

530 - 1710 KHz (USA)

522 - 1620 KHz (Europe)

522-1620 KHz (Russia)

Usable Sensitivity Better than 45dB

USB DEVICES:

USB flash memory USB 1.1 & 2.0 compatible

BLUETOOTH

Output Power Class 2

Frequency Band 2.4000GHz - 2.4835GHz

Typical Range 3 Metres (no obstructions)

Standard Bluetooth 2.0 specification

SUPPORTED FILE FORMATS

MPEG1/2/2.5 Layer 2/3

WMA Version 7/8/9

Sampling frequency

MPEG1 32/44.1/48 kHz

MPEG2 16/22.05/24 kHz

MPEG2.5 8/11.025/12KHz

WMA 22/32/44/48KHz

Sampling Bit rate

MP3/WMA 32\~320Kbps & VBR

ISO9660 Level 1/2 & Joliet (unicode)

Max File/DIR. Count 999

Max DIR. Depth 255

Sorting Method Tree sorting

Max File/DIR. Name 64Byte

ID3 V1.0/1.1/2.0/2.3 [Max 32 Byte]

MP3 dir shown in manual as "Folder"

MP3 file referred to as "Track".

Maximum length of file name 28 characters.

Maximum length of directory 16 characters.

Supports Multi-Session recording.

NOTE: Product specifications are subject to change without prior notice.

REGISTER YOUR PRODUCT ONLINE:

For your own peace of mind, register your product purchase online at www.fusionelectronics.com

We'll keep you up to date with any news related to your product or new accessories to help you get the most from your product.

By registering your product you can be assured that if the unexpected occurs we'll have your details and be ready to help.

LICENSING

Made for

iPod iPhone

"Made for iPod and "Made for iPhone" mean that an electronics accessory has been designed to connect specifically to iPod or iPhone respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. Apple is not responsible for the operation of the device or its compliance with safety and regulatory standards.

iPod and iPhone are trademarks of Apple inc., registered in the U.S. and other countries.

Windows Media and the windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Bluetooth®

The Bluetooth word mark and logos are owned by the Bluetooth SIG, inc and any use of such marks by FUSION ELECTRONICS is under license. Other trademarks and trade names are those of their respective owners.

THE FUSION PROMISE OF QUALITY

LIMITED 1 YEAR CONSUMER WARRANTY

FUSION Electronics Limited 'FUSION' warrants this FUSION Speaker, Subwoofer, Amplifier Head Unit or genuine FUSION Accessory 'product' is free from defects in material and workmanship, according to the following terms and conditions:

• The limited warranty for the FUSION product purchased extends to the first twelve [12] months beginning on the date of purchase of the product.
• The limited warranty extends only to the original consumer purchaser (consumer) of the product and is not assignable or transferable to any subsequent purchaser/end user.
- The limited warranty extends only to consumers who purchase the product in one of the countries (or areas) set forth on www.fusionelectronics.com. The limited warranty is only valid in FUSION'S intended country (or area) of sale of the product.
- During the limited warranty period, FUSION or its authorised service network will repair or replace, at FUSION or FUSION'S authorised dealer, any defective product or parts thereof with new and return the product to the consumer in working condition. No charge will be made to the consumer for either parts or labour in repairing or replacing the product. All replaced parts and cosmetic parts should be free of defects at the time of shipment and, therefore shall not be covered under these limited warranty terms.

- Repaired product will be warranted for the balance of the original warranty period or for ninety (90) days from the date of repair, whichever is longer. - All warranty claims must be accompanied with a copy of this warranty card, and a copy of proof of purchase date.

The consumer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable:

- The product has been subject to: abnormal use, abnormal conditions, improper storage, exposure to excessive moisture or dampness, exposure to excessive temperature or other such environmental conditions, unauthorised modifications, unauthorised connections, unauthorised repair including but not limited to use of unauthorised spare parts in repairs, misuse, neglect, abuse, accident, alteration, improper installation, acts of God, spill of foods or liquids, maladjustment of customer controls or other acts which are beyond the reasonable control of FUSION, including deficiencies in consumable parts such as fuses, and breakage or damage to antennae unless caused directly by defects in materials or workmanship, and normal wear and tear of the product.

• FUSION was not notified by the consumer of the alleged defect or malfunction of the product during the applicable limited warranty period.

• The product serial number or the accessory date code has been removed, defaced or altered.

• The product was used with or connected to an accessory not supplied by FUSION or fit for use with FUSION product, or used in a manner other than its intended use.

If a problem develops during the limited warranty period, the consumer should take the following step-by-step procedure:

1. The consumer shall return the product to the place of purchase for repair or replacement processing.

2. The consumer shall also be charged for any parts or labour charges not covered by this limited warranty.

The consumer shall be responsible for expenses related to reinstallation of the product

1. If the product is returned to FUSION after the expiration of the warranty period, FUSION's normal service policies shall apply and the consumer will be charged accordingly.

THE BENEFITS CONFERRED BY THIS LIMITED WARRANTY APPLY TO THE EXTENT THAT THEY ARE NOT SUPERCEDED BY ANY OTHER RIGHTS AND REMEDIES UNDER ANY APPLICABLE LEGISLATION THAT CANNOT BE EXCLUDED. OTHERWISE, TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTY IS EXCLUDED AND THE FOREGOING WARRANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. TO THE EXTENT PERMITTED BY LAW, FUSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR A LOSS OF ANTICIPATED BENEFITS OR PROFITS, OUT OF USE OR INABILITY TO USE THE PRODUCT.

- Some states in America do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives your specific legal rights which may vary from state to state.

- FUSION neither assumes nor authorises any authorised service centre or any person or entity to assume for it any other obligation or liability beyond that which is expressly provided for in this warranty.

- All warranty information, product features and specifications are subject to change without notice.

AUSTRALIAN CONSUMERS

FUSON®

LIMITED 1 YEAR CONSUMER WARRANTY

Fusion Electronics Pty Limited, Unit 21/130 Kingston Road, Underwood, Queensland, 4119, Australia. EMAIL: [e-mail] PHONE: [phone]

THE FUSION PROMISE OF QUALITY LIMITED 1 YEAR CONSUMER WARRANTY

This warrant is given in addition to other rights and remedies available to the consumer under Australian Consumer Law. In addition to the Fusion Warranty our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any others reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

FUSION Electronics Limited 'FUSION' warrants this FUSION Product including Speaker, Subwoofer, Amplifier Head Unit or genuine FUSION Accessory 'product' is free from defects in materials and workmanship, in accordance with the following terms and conditions:

- The limited warranty for the FUSION product purchased is only available for [12] months after the date of purchase.

- The limited warranty extends only to the original consumer of the product and may not be assigned or transferred to any other person or consumer without Fusion's prior written consent being provided.

- During the limited warranty period, FUSION or its authorised service network will repair or replace any defective or faulty product or parts at its own cost.

• Repaired or replaced product will be warranted for the balance of the original warranty period or for ninety (90) days after the date of repair, whichever is longer.

- All warranty claims must be notified to Fusion or its authorised Dealer in writing during the warranty period accompanied with a copy of this warranty card, proof of purchase date and the product with an intact and unaltered serial number or accessory date code.

This Warranty will not apply if:

The consumer causes the Product to be of unacceptable quality or fails to take steps to prevent the Product from becoming of unacceptable quality and/or it is damaged by abnormal use. Examples of goods becoming of unacceptable quality or of abnormal use by the consumer include;

• Storage of product under improper conditions.

- Exposure to excessive moisture or dampness

- Exposure to excessive temperature extremes or other adverse environmental conditions.

• Unauthorised modifications of product, connections or otherwise unauthorised repairs including, but not limited, to the use of unauthorised parts in the repair of products

- Improper use of or installation of, or interference with, product adjustments or controls and or including antenna breakage or damage due to misuse

- Damage caused by consumables or by electricity supply.

- Acts of god [force majeurel, exposure of product to food spills, or any other type of fluid ingress

• Using the product in a way for which was not intended to be used or connecting it to an accessory not supplied by, specified by, or authorised by Fusion

- Any other abnormal use of or conduct causing product to become of unacceptable quality

Other exclusions;

- This warranty extends to the repair or replacement of Fusion product only and the consumer is responsible for any expenses relating to the removal or installation of the product or related services including the cost of delivering the product to Fusion or its authorised dealer.

- Repair work conducted by Fusion after this warranty has expired or if this warranty for any other reason this Fusion warranty does not apply is subject to Fusion's normal service policies and Fusion charges for labour and material may apply.

- This is a manufacturer's warranty provided to consumers of Fusion products. Variations to this warranty may only be made by Fusion and will be notified to the customer in writing or issued on the Fusion website. Fusion Dealers, agents and authorised dealers are not authorised to make changes or vary this Fusion warranty.

- All warranty information, product features and specifications are subject to change without notice.

- Fusion is not responsible for replacing or the cost of replacing any consumer data lost occurring either due to equipment failure, or during the repair and replacement process.

FRANÇAIS

LA PROMESSE DE QUALITE FUSION

GARANTIE LIMITEE 1 AN

FUSION Electronics New Zealand

093692900

FUSION Electronics Australia

1300 736 012

FUSION Electronics Europe

[phone]

FUSION Electronics USA

623 580 9000

FUSION Electronics Pacific

[phone]