WIPG-300H - Wireless pointer Planet - Free user manual and instructions

Product Type	802.11n Wireless Interactive Presentation Gateway
Model	WIPG-300H
Brand	Planet
Dimensions (W x D x H)	150 x 59 x 25 mm
Weight	243 g
Power Supply	5V DC, 2.6A external adapter with interchangeable plugs (US, EU, UK, AU)
Video Output	VGA (D-sub 15-pin) and HDMI 1.4b, up to 1080p Full HD
Wireless Standard	IEEE 802.11a/b/g/n, dual band (2.4GHz and 5GHz), up to 300 Mbps
Interfaces	1× 10/100BASE-TX RJ45, 3× USB 2.0 Type A, 1× 3.5mm audio out
Antenna	2× detachable RP-SMA dual dipole antennas (2 dBi, omnidirectional)
Number of Wireless Clients	Up to 15 simultaneous wireless clients
Split Screen	4-to-1 split screen projection
Supported OS	Windows 7/8/10, Mac OS X 10.9+, Android 4.1+, iOS 4.3+
Key Features	Wireless projection, USB over IP (UoIP), WebSlides, SidePad remote control, AP/AP Client modes, GateKeeper network security
Management	Web-based UI, default IP 192.168.1.1, default password admin
LED Indicators	Green: power on; Red: init/firmware upgrade
Material	Metal enclosure
Operating Temperature	0°C to 40°C
Safety Compliance	FCC Part 15 Class B, CE RED 2014/53/EU
Spare Parts / Accessories	Antennas, power adapter with plug set, wall-mount kit, USB token, quick installation guide
Cleaning and Maintenance	Disconnect power, wipe with dry cloth; avoid liquids and abrasives.

Frequently Asked Questions - WIPG-300H Planet

How do I reset the WIPG-300H to factory defaults?

Power off the device, press and hold the reset button (using a paper clip) while plugging in the power adapter. Hold for 10–15 seconds until the LED indicates reset. Default username and password are both 'admin'.

Can I use HDMI output without changing settings?

Yes. To use HDMI directly, plug the HDMI cable into the WIPG-300H and the display, then power on the WIPG-300H. The default output is VGA, but if HDMI is connected before power-on, it will be automatically selected.

How many users can connect to the WIPG-300H simultaneously?

The device supports up to 15 wireless clients for projection. For WebSlides, up to 35 users can view slides with an update interval of 90 seconds.

What mobile apps are available for wireless presentation?

Use MirrorOp Sender for Windows/Mac, MirrorOp Presenter for Android/iOS, and MirrorOp Receiver for SidePad remote control. Download from the WIPG-300H web UI or app stores.

How do I enable the 4-to-1 split screen?

Connect up to four PCs/laptops to the WIPG-300H. In the MirrorOp utility or Conference Control web page, use the 'Play Split' buttons (#1–#4) to assign each client to a quadrant.

What is the default IP address and how do I change it?

The default IP is 192.168.1.1. To change it, log in to the web UI (user: admin, password: admin), go to Network Setup, and select 'Use the following IP address' to enter a static IP.

Can I use the WIPG-300H as a wireless access point for internet?

Yes. In its default AP mode, clients can access the internet via the WIPG-300H's LAN port. You can also enable AP Client mode to connect to an existing wireless network.

How do I update the firmware?

Download the latest firmware from PLANET's website. Log in to the web UI, go to Admin > Firmware Upgrade, browse to the file, and click Upgrade. Do not power off during the process.

Is the WIPG-300H compatible with Mac OS X?

Yes. It supports Mac OS X 10.9 and above. Download the MirrorOp Sender for Mac from the web UI. Additional installation of Soundflower may be required for audio projection.

How do I use a USB keyboard or mouse with the WIPG-300H?

Plug a standard USB keyboard or mouse into any USB port on the WIPG-300H. It will control the computer that is currently projecting remotely. Ensure 'Allows control inputs from receivers' is enabled in the MirrorOp preferences.

USER MANUAL WIPG-300H Planet

Black wireless router device with two antennas and ports (no visible text or symbols on body)

802.11n Wireless Interactive Presentation Gateway

WIPG-300H

Woman in business attire using a laptop on stairs (no visible text or symbols)

Copyright

Copyright © 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance, for example, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

CE mark Warning

This is a class B device, in a domestic environment; this product may cause radio interference, in which case the user may be required to take adequate measures.

CE Compliance Statement

This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when it is used at a safe distance of 20 cm from your body.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria Belgium, Denmark, Finland, and France (with Frequency channel restrictions). Germany, Greece, Ireland, Italy, Luxembourg. The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version of this device is also authorized for use in EFTA member states Iceland, Liechtenstein, Norway and Switzerland.

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

User Manual of PLANET 802.11n Wireless Interactive Presentation Gateway with 1080p Full HD

Model: WIPG-300H

Rev: 2.0 (March, 2017)

Part No. EM-WIPG-300H_v2.0 (2081-E60070-001)

Contents

Chapter 1.PRODUCT INTRODUCTION....6

1.1 Package Contents 6
1.2 Product Description....6
1.3 Product Features....10
1.4 Product Specifications 11

Chapter 2. HARDWARE INSTALLATION....14

2.1 Hardware Description 14

2.1.1 The Front Panel 14
2.1.2 LED Indications.... 14
2.1.3 The Rear Panel.... 15

2.2 Hardware Connection 15

Chapter 3.WINDOWS CLIENT UTILITY – MirrorOp .... 18

3.1 Starting Program 18
3.2 Control Panel 19
3.3 Preferences....20

3.3.1 General 20
3.3.2 Favorites 21
3.3.3 Advanced....22
3.3.4 Setup hotkeys 24
3.3.5 About 25

3.4 SidePad 26
3.5 WebSlides 33

Chapter 4.MAC OS X CLIENT UTILITY....37

4.1. Mac OS X Quick Connection....37
4.2. Download Mac OS X Client Utility 39
4.3. Main User Interface 43
4.4. Screen Projection....43
4.5. MAC Audio Projection.... 44

Chapter 5.WEB UI MANAGEMENT....48

5.1. WIPG-300H Homepage....48
5.2. Download 49
5.3. Conference Control....50
5.4. Admin 51

5.4.1. System Status....51
5.4.2. Device Setup 53
5.4.3. Network Setup 54
5.4.4. OSD Setup....59
5.4.5. Change Passwords 60
5.4.6. Reset to Default 60

5.4.7. Firmware Upgrade....61
5.4.8. Webslides Setup....62
5.4.9. Reboot System 63

Appendix A: Configuring the PCs....64

Appendix B: FAQ 68

Chapter 1. PRODUCT INTRODUCTION

1.1 Package Contents

The following items should be contained in the package:

WIPG-300H × 1

Antenna × 2

5V DC Power adapter + World-Wide Plug Set × 1

Product photo of a black electronic device with cables and two small accessories (no visible text or symbols)

Wall-mount Kit x 1

Metallic rectangular metal bracket with mounting holes and a small metallic connector attached (no text or symbols visible)

USB Token × 1

Quick Installation Guide × 1

If there is any item missing or damaged, please contact the seller immediately.

1.2 Product Description

Exterior view of a wireless router device with two antennas and ports (no visible text or symbols on the device body)

Featuring Full HD Resolution and High-quality Video and Audio

PLANET WIPG-300H 802.11n Wireless Interactive Presentation Gateway supports 1080p Full HD resolution and delivers high-quality audio and video projection. Thus, the WIPG-300H can be used not only for office presentation but also for home entertainment. Home users can easily share the multimedia on a big monitor and screen with friends without the hassle of cabling. Furthermore, the WIPG-300H's output resolution of up to 1920 x 1080 is perfect enough for giving presentations or playing videos.

Delivering Smooth Presentations Wirelessly

The WIPG-300H is based on the selectable IEEE 802.11n dual band technology. It is equipped with both VGA and HDMI video output interfaces and one 10/100Mbps Ethernet port for LAN connection. With the hardware decoding capability, the WIPG-300H can project high-definition video on the screen and audio through wireless or wired LAN connection. It wirelessly facilitates multiple users to freely display presentations, images and videos via wireless connection to a projector or LCD TV without much cabling.

Dual Video Output Interfaces

To be able to be interoperable with most of the popular display devices, the WIPG-300H is equipped with two types of video output interfaces: the VGA and HDMI connectors. You can connect it to any type of projector, LCD TV, or other large screen display wirelessly right away.

4-to-1 Split Screen Projection

With this 4-to-1 split screen feature, the WIPG-300H allows up to four PCs or laptop screens to be projected through one projector at the same time. Therefore, the participants can easily do a side-by-side comparison of the four PCs or laptops to make their meeting more efficient.

Interactive with UoIP and APP

The WIPG-300H features UoIP (USB over IP) technology which can touch screen by using USB cable to wirelessly control the touch screen. Both iOS and Android apps are offered to allow audience to use either of the web browser to view the speaker's slides or control the projection screen via mobile devices.

Easy to Use – Just Plug and Display

The embedded Windows-based utility enables the connected users to directly download the utility from the WIPG-300H web UI or simply execute the utility from the created USB token. It offers the most convenient way for the new user to access the presentation in seconds. Just link the PC or laptop to the WIPG-300H wirelessly or via Ethernet and the wireless projection can be immediately in use via the connected projector.

graph TD
    A["MacBook"] --> B["WIPG-300H"]
    B --> C["VGA"]
    C --> D["Projector"]
    E["Laptop"] --> F["WIPG-300H"]
    F --> G["VGA"]
    G --> H["Projector"]
    I["OR"] -.-> B
    J["Insert The WIPG PnS Token and Start Presentation"] --> K["WIPG-300H"]

Internet / Intranet Connectivity

The WIPG-300H is also a Wireless Access Point. The 10/100Mbps LAN port and 11n wireless performance ensures the participants in the meeting are able to access the Internet and Intranet all the time, even while wireless presentations are projecting.

AP Client Mode

When the AP Client Mode function is enabled, the WIPG-300H will act as the existing Access Point through Wi-Fi. This feature provides the flexibility of wireless network deployment in enterprise environment.

Wi-Fi AP Client Mode

Internet

Wireless Projector

Tablet

Wi-Fi AP / Router
AP Client Connection

Black wireless router with two antennas and a blue cable, emitting signal waves (no text or symbols visible)

WIPG-300H
AP Client Enable

Remote Desktop

When you plug the standard USB keyboard or mouse into the USB port of the WIPG-300H, you can control your PC remotely. You don't have to stand still by the PC or WIPG-300H when giving your presentation. Instead, you can move around when making the presentation.

Remote Desktop

Interior scene with a laptop, wireless network icons, and connected devices including a router, keyboard, and mouse (no text or symbols visible)

1.3 Product Features

■ Wirelessly project multimedia with PCs, laptops and mobile devices.
■ VGA/1080p HDMI output
■ 4-to-1 split screen projection
■ Audio and video streaming
■ Just Plug & Display
■ 802.11n dual band Wi-Fi AP and AP-client mode
- Remote control presenter's desktop over USB mouse/keyboard
■ USB over IP for touch screen and IWB
■ Web browser management
■ Windows 7/8/10, Mac OS X, iOS and Android support
■ WebSlides allows multiple users to view the presentation on any mobile devices
■ SidePad receiver allows mobile device to remotely control presenter's desktop
■ Compact size -- convenient for installation and placement

1.4 Product Specifications

Product	WIPG-300H
Hardware Specifications
Interfaces	Video	VGA Port: D-sub 15-pin female portHDMI 1.4b
	Audio Out 3.5mm	stereo jack
	LAN	10/100BASE-TX RJ45
	Wireless LAN IEEE	802.11a/b/g/n 5Ghz/2.4GHz selective300Mbps
	USB Port	3 x USB 2.0, Type A, 5V DC, 0.5A output
Antenna	Gain	2 x 2dBi RP-SMA detachable dual diapoleantenna
	Orientation Omni-directional
LED Indicators	Green: Power onRed: Init / firmware upgrade
Material	Metal
Dimensions (W x D x H)	150 x 59 x 25mm
Weight	243g
Power	External power adaptor: 5V DC input, 2.6AMulti-type swappable plug: US, EU,UK, AU
Reset Button	>10 sec while booting: reset to factory default
Wireless Interface Specifications
Standard	Compliance with IEEE 802.11nBackward compatible with IEEE 802.11a/b/g
Frequency Band	2.4GHz	FCC: 2.412~2.462GHzETSI: 2.412~2.484GHz
	5GHz	FCC: 5.180~5.240GHz, 5.725~5.850GHzETSI: 5.180~5.240GHz
Wireless Data Rate	Up to 300Mbps
Wireless Channel	2.4GHz	FCC: 1~11ETSI: 1~13
	5GHz	FCC:36, 40, 44, 48, 149, 153, 157, 161, 165ETSI:36, 40, 44, 485GHz channel list will vary in different countriesaccording to their regulations.
Receive Sensitivity	802.11b: less than -80 dBm (11Mbps)802.11g: less than -70 dBm (54Mbps)802.11n: less than -61 dBm at HT40 MCS7
	802.11n: less than -64 dBm at HT20 MCS7
Wireless Security	IEEE Standard 64/128 bit WEP / WPA / WPA2-PSK
Operation Mode	■ AP (Access Point)■ AP Client
Wireless Client	Supports max. 15 clients
Video Display
Supported Output Resolution	VGA:SVGA (800x600) / XGA (1024x768)WXGA(1280x768) / WXGA(1280x800)WXGA (1360x768) / WXGA+ (1440x900)UXGA (1600x1200)HDMI:720p (1280x720) / 1080i (1920x1080) / 1080p (1920x1080)
System Management
Protocol	TCP/IP
IP Configuration	Automatic: DHCPManual: Static IP address
Management	Web-based configuration
Supported Windows Account Right	AdministratorsLimited userGuest
Supported Operating System	■ Windows 7 / 8 / 10➢ CPU: Dual core 1.8GHz or above➢ VGA: nVIDIA/ATI graphic card with 64MB VRAM or above➢ RAM: 8GB DDR3 or above* Recommend at least Intel Core i5 2.6GHz for video streaming■ Mac OS X 10.9 and above➢ CPU: Intel Dual Core 1.4GHz or above➢ VGA: nVIDIA/ATI graphic card with 64MB VRAM or above➢ RAM: 8GB DDR3 or above■ Android 4.1 and above■ iOS 4.3 and above
Language Support	EnglishTraditional ChineseSimplified ChineseJapaneseKoreanFrench

Software Features
Software Name: MirrorOp Sender
Platform Windows MacOS
4-to-1 Split Screen	■	■
Audio Projection	■	■Extra utility required
Document Projection	■	■
Photos Projection	■	■
Video Projection	■	■
Virtual Extended Desktop	■	■
Conference Control	■	■
Gatekeeper	■	■
*Webslides	■	■
Software Name: MirrorOp Presenter
Platform	Android	iOS
4-to-1 Split Screen	■	■
Document Projection	■	■
Photos Projection	■	■
*SidePad App: MirrorOp Receiver	■	■
*Webslides	■	■
Remarks:
SidePad Feature	Allows mobile device to remotely control presenter's desktop through the MirrorOp Receiver App.
Webslides Feature	Allows audiences to view the presentation and save single slide directly on any mobile devices.
	Supports max. 35 clients (update interval: 90 seconds).
Standard Conformance
IEEE Standards	IEEE 802.11n (2T2R, up to 300Mbps)IEEE 802.11gIEEE 802.11bIEEE 802.11aIEEE 802.3 10BASE-TIEEE 802.3u 100BASE-TX
Environment
Temperature	Operating: 0 ~ 40 degrees CStorage: -10 ~ 60 degrees C
Humidity	Operating: 10 ~ 80% (non-condensing)Storage: 10 ~ 90% (non-condensing)

Chapter 2. HARDWARE INSTALLATION

Please follow the instructions below to build the wireless network connection between the WIPG-300H, display equipment and your computers.

2.1 Hardware Description

2.1.1 The Front Panel

The front panel provides a simple interface monitoring the wireless presentation gateway. Figure 2-1 shows the front panel of WIPG-300H.

Front Panel

Figure 2-1 WIPG-300H Front Panel

■ USB Port: USB 2.0 ports for USB keyboard and mouse.

User can control the projection of PC remotely by simply plugging standard USB keyboard or mouse into the WIPG-300H.

2.1.2 LED Indications

The front panel LEDs indicate instant status of system power and help monitor and troubleshoot when needed. The table below shows the LED indications of the Wireless Present Gateway.

LED (Green)	Description
On Power On
Off Power Off

2.1.3 The Rear Panel

Rear Panel

Figure 2-2 WIPG-300H Rear Panel

2.2 Hardware Connection

Step 1. Please turn off your projector first, and connect HDMI or D-sub cable of the projector to the WIPG-300H. Then you can power on the WIPG-300H.

Figure 2-3 VGA / HDMI Interface Connection

Step 2. When the projector shows the default screen as shown below, it indicates the WIPG-300H is ready now.

Figure 2-4 Projector Default Screen

Step 3. Use your laptop or desktop for site surveying the wireless signal of the WIPG-300H, and connect your PC with it wirelessly. The default SSID is WIPG-300H.

Figure 2-5 Windows Platform Wireless Site Survey
Step 4. Open the web browser and it will redirect to the WIPG-300H web page automatically, or you can enter the default IP address 192.168.1.1 to access it.

Figure 2-6 WIPG-300H Web UI Screenshot

Now you can configure the WIPG-300H and download the client utility (WIPG) of Windows 7 / 8 / 10 via web UI. For further information of the configurations, please refer to the following chapters.

You can download Utility for Windows from here.

Download (Windows 7/8/10)

Note:

For Internet Explorer 8 and above, please disable the "SmartScreen Filter" first to download and install this software.

Chapter 3. WINDOWS CLIENT UTILITY – MirrorOp

3.1 Starting Program

After installing WIPG (Wireless Interactive Presentation Gateway) utility downloaded from the web page of the WIPG-300H, please follow the steps below to start.

Step 1. Click MirrorOp icon

on the desktop to execute the program.

Step 2. The utility will start to search the available access points automatically if you have not connected your PC to the WIPG-300H manually. When the WIPG-300H is displayed in the list, please click it to connect and then enter the Login Code shown on the projector screen.

Figure 3-1 MirrorOp – Access Point Connection

Figure 3-2 MirrorOp – Access Point Login

Step 3. Click the

button to start projection

Figure 3-3 MirrorOp – Control Panel

3.2 Control Panel

graph TD
    A["Settings"] --> B["WIPG-300H Displaying"]
    C["Expand/Collapse device list"] --> D["Full/Split Screen"]
    C --> E["Pause"]
    C --> F["Stop"]
    C --> G["Mute"]
    H["Collapse/Expand the panel"] --> I["Minimize the interface"]
    J["Close the application"] --> K["Settings"]

Figure 3-4 MirrorOp - Control Panel Function Introduction

Button	Description	Button	Description
	Start Full Screen Projection		Display on bottom-right
[6D07]	Display on top-left		Stop projecting
	Display on top-right		Pause The Projection Screen
	Display on bottom-left

Please refer to the following sections for detailed instructions of the menu.

3.3 Preferences

Click "Preferences" to open the web UI page of WIPG-300H. To set your preferences, open the Preferences dialog from the Preferences button.

Figure 3-6 MirrorOp – Preferences

3.3.1 General

This is where you set the following general preferences.

Figure 3-7 MirrorOp -General

The page includes the following fields:

Object Description
Name	The name which is shown on the Conference Control list used to identify this sender. You can use any character or numbers up to 32 characters.
Functions	● Allows controlling from tablets:When this option is enabled, you can use a special mobile app to connect to the receiver, and then see the screen of your computer and control it while it's displaying. This is useful if you want to move around when presenting and use a tablet to control your computer.● Allows screen projection to be redirected to browsers:When turned on, when your screen is displaying on the receiver, users can also use any web browser to see your screen and save it as image files. This function must also be supported by the receiver device. A different receiver device may have a different term as to this function, for example, WebSlides, Remote View, etc. Please refer to the manual of your receiver device to understand how to enable this function.● Allows control inputs from receivers:When turned on, you can control this computer with input devices (mouse, keyboard, touch panel) that are attached to the receiver. If you don't want to let user control you computer from the receiver side, turn this option off.
Audio: (Windows only)	● Mute PC audio when projecting:When enabled, the PC will be muted when projecting to avoid echo in the same room. If you want to keep PC audio output, uncheck this option.
Others:	● Always on top:When enabled, the MirrorOp window will always be placed on top of all windows so that you can always access it even when using other applications. Always on top may not work if other application is running as full-screen mode, for example, some video players.

3.3.2 Favorites

Favorites list is useful if you mostly use the same receivers. You can tell MirrorOp to direct start from your favorites list without going through the discovery process. If you like to start MirrorOp from your favorites list, choose "Favorites". If you like to start by searching for receivers, choose "Auto Discovery".

Figure 3-8 MirrorOp -Favorites

You can also import or export favorites list in order to exchange list with other computers or colleagues.

To export your list, click the "Export" button, and then select the folder to save it.

To import favorites from a file, click "Import" and then locate the favorites file. The contents of the external file will be copied to the current list. The original contents of the current list will be over written.

3.3.3 Advanced

In most cases, you can skip this section. MirrorOp tries to use appropriate default settings chosen by the capabilities of your computer, network and receiver. However, if you want to adjust some settings to get better results yourself, you can do it here. You may want to make sure you know what you're doing before changing the settings. Usually it doesn't explode if a setting is inappropriate though.

Figure 3-9 MirrorOp -Advanced

The page includes the following fields:

Object Description
Mode	Choose "Duplicate" if you want to see the same image as on your main desktop. Choose "Extend" if you want to use virtual extended desktop.Additional driver may be necessary to enable the extended mode.Please download and install the driver when prompted.
Aspect Ratio	Determines aspect ratio on receiver screen when the aspect ratio of the computer and receiver display is different.Fit to full screen:Stretch image to fill the receiver display regardless of aspect ratio.Note that if the original aspect ratio of the computer and the receiver are very different, the resulted image may be obviously distorted.Keep aspect ratio:Keep the original aspect ratio of the computer. Stretch image to fit the receiver display so that it reaches horizontal or vertical edges.Note that if the original aspect ratio of the computer and the receiver are very different, there will be late black borders on the receiver display.
Remote USB Support:	● Universal multi-touch:Receives multi-touch commands from touch devices and translate into commands to fit sender OS. Please note that some special commands that require specific driver supports may not be supported.● Simulate local USB:Simulate remote USB device as local device in Windows. Windows will recognize the remote device and use original driver of that device.

3.3.4 Setup hotkeys

Hotkeys are handy if you use certain functions frequently. MirrorOp supports most system hotkeys, for example, copy-paste to input or edit text. There are some MirrorOp-specific controls you can also trigger with hotkeys. The default hotkey definitions are listed on this tab. If you prefer to use your own definition, you can also change the definition here.

Figure 3-10 MirrorOp – HotKey

To change a hotkey, click "Enable" to change the hotkey combination you want to use. The new definition should appear in the edit box. Please note that the definitions cannot conflict with other controls or system definitions, otherwise, they may not work properly. If you enter a combination which is currently used by another control, the definition will be assigned to the current control you're editing; the previous one will be cleared. When you're done editing, simply click "OK" (Windows) or close the dialog. If you would like to restore to default definitions, click the "Restore Defaults" button.

3.3.5 About

On the About tab you can check the version number, access Help file, visit MirrorOp web site, or re-visit the Start Guide.

Figure 3-11 MirrorOp - About

3.4 SidePad

SidePad is a function to allow the user to connect Pad/Smartphone (Android and iOS), PC and display/projector via the WIPG-300H. User can then control the projecting PC via Pad/Smartphone by the app, MirrorOp Receiver. Please refer to the image below for more information.

graph TD
    A["SidePad"] --> B["HDMI/VGA"]
    B --> C["WIPG-300H"]
    C --> D["User Interface"]
    D --> E["User Interface with Remote Icon"]
    E --> F["User Interface with Hand Icon"]

Remotely control your laptop with your mobile device when projecting

SidePad Control for Android /iOS device

■ Android: Download "MirrorOp Receiver" from Google Play
■ iOS: Download "MirrorOp Receiver" from Apple Store.

1. PC/Mac with WIPG utility installed
2. Click the "Setting" icon and select "Preferences".

3. Check "Allows controlling from tablets"

4. Set the pass code (default is: 1111)

5. Tablet/Smartphone with the "MirrorOp Receiver" app installed

Android

- Open the "MirrorOp Receiver" app. Long press the Menu button on your Android device, and click "Settings".

- Check "Search for sender on start".

• Close MirrorOp Receiver and reopen it.
• You will see the name of PC/Mac with WIPG utility installed.

- Select which PC/Mac you want to control and enter the pass code set earlier.

- Now you can remote control the PC/Mac from your Tablet/Smartphone.

iOS

- Go to "Setting" on your iOS device, and click "Receiver".

- Enable "Search for senders on start".

• Open the "MirrorOp Receiver" app.
• You will see the name of the PC/Mac with WIPG utility installed.

- Select which PC/Mac you want to control and enter the pass code set earlier.

- Now you can remotely control the PC/Mac from your Tablet/Smartphone.

3.5 WebSlides

WebSlides is an application to allow the user/presenter to broadcast the projecting screen/slides to allow multiple login users to receive the slides during a presentation and save the slides for note-taking later.

graph TD
    A["Presenter"] -->|WIPG-300H| B["Projector"]
    B --> C["Mac Books"]
    B --> D["Smart Phones"]
    B --> E["Tablet"]
    B --> F["Laptop"]
    C --> G["Signal waves"]
    D --> H["Signal waves"]
    E --> I["Signal waves"]
    F --> J["Signal waves"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#cff,stroke:#333
    style F fill:#ffc,stroke:#333

Open your web browser and view presentation slides on your devices

Note

Webslides is not available when Quad view is in use.

Presenter

● Make sure your PC/Mac is connected to WIPG-300H on the WebSlides Setup page.

PLANET

Networking & Communication

Wireless Interactive Presentation Gateway

WIPG-300H > Admin > WebSlides Setup

Logout »

System Status

Device Setup

Network Setup

OSD Setup

Change Passwords

Reset to Default

Firmware Upgrade

WebSlides Setup

Reboot System

Auto Refresh Interval (second)

Access Password Control

Manual Refresh

○10 *recommended maximum concurrent users. (10)
○20 *recommended maximum concurrent users. (15)
○30 *recommended maximum concurrent users. (20)
○45 *recommended maximum concurrent users. (25)
○60 *recommended maximum concurrent users. (30)
○90 *recommended maximum concurrent users. (35)

Disable

○ Use the same password as "Code"
Use the following Code:

(0-9)

Note

If there are more than 10 users logged into WIPG, it is recommended to connect WIPG to company network through Ethernet or bridge WIPG to a router due to wireless bandwidth concern. User should connect WIPG via company network or router in order to secure the projection performance.

Apply

Cancel

● Make sure the WebSlides function is enabled by the WIPG utility.

Audience

● The audience also needs to connect to WIPG-300H via Wi-Fi.
- Open the browser of the audience's device and enter the IP address of WIPG-300H on the URL of browser.

- Once the users are connected, they will see the image below on their devices. Click on the "Webslides" button to start receiving the presenter's slides and the image can be seen on the audience's browser.

Wireless Projection function and Conference Control function can support up to 64 users.

Note

The WIPG logged-in user is not identical to WebSlides user, and they both consume the wireless bandwidth for device connection. If there are more than 10 users logged into WIPG, it is recommended to connect WIPG to company network through Ethernet or bridge WIPG to a router due to wireless bandwidth concern. User should connect WIPG via company network or router in order to secure the projection performance.

The WebSlides user number should not exceed the recommended number on the web management page to prevent the failed connection or low projection performance.

Chapter 4. MAC OS X CLIENT UTILITY

4.1. Mac OS X Quick Connection

Step 1: Right-click on the network icon displayed in the system tray. The AirPort Network Connection menu will appear.

Figure 4-1

Step 2: Highlight and select the wireless network (SSID) to connect.

(1) Select an SSID [WIPG-300H].
(2) Double-click on the selected SSID.

Figure 4-2

Step 3: Enter the encryption key of the WIPG-300H.

(1) Enter the encryption key that is configured in Section 5.4.3
(1) Click the [Join] button.

Figure 4-3

If you want to connect this WIPG-300H in the future, check [Remember this network].

Step 4: Check if the AirPort is connected to the selected wireless network. If "Yes", then there will be a "check" symbol in front of the SSID.

Step 5: Open the web browser and it will redirect to WIPG-300H home page automatically. Or you can enter the default IP address http://192.168.1.1 to access it.

Figure 4-4

After a moment, the main screen appears as shown in Figure 4-5

Figure 4-5

4.2. Download Mac OS X Client Utility

Step 1. : Click "Download".

Step 2. : Choose the utility for "MAC" and then click the Download button and execute the installation program.

Figure 4-6

Figure 4-7

Step 3. : Install MirrorOp utility to Applications.

Figure 4-8

Step 4. Click the "MirrorOp" icon to execute the program.

Figure 4-9
Step 5. WIPG will start to search the available access points automatically if you have not connected your MAC to WIPG-300H manually. When the WIPG-300H is displayed in the list, please click it to connect and then enter the Login Code shown on the projector screen.

Figure 4-10

Step 6. Ready to execute the program.

Figure 4-11

4.3. Main User Interface

Figure 4-12

4.4. Screen Projection

Click the "Play" button for a full or split screen and you can project the main screen on to the display immediately. Click the "Pause" button and you can freeze you projection screen, and click the "Stop" button to stop projecting your screen.

Figure 4-13

Button	Description	Button	Description
	Start Full Screen Projection		Display on bottom-right
	Display on top-left		Stop projecting
	Display on top-right		Pause The Projection Screen
	Display on bottom-left

4.5. MAC Audio Projection

Before starting Audio Projection, please install the "Soundflower.mpkg" (MAC system extension for audio use) on your computer. Please find the software in USB Token.

1) Execute the "Soundflower.pkg" in the Mac OS.
2) It will pop up a window "Welcome to the Soundflower Installer" and then please click "Continue".

Figure 4-14

3) After reading the important information, please click "Continue" to go to the next step.

Figure 4-15

4) Click "Install".

Figure 4-16

5) Enter your Username and Password of the System. Then, click "Install Software".

Figure 4-17

6) When the installation is successful, click "Close".

Figure 4-18

7) After installation, you will see there is a sunflower icon displayed in the system taskbar. Then, you can configure your audio output per your preference.

※ If the icon is not displayed, please execute the program of WIPG-300H first.

Figure 4-19

Chapter 5. WEB UI MANAGEMENT

Please follow the steps below to enter the web UI of WIPG-300H.

Step 1. First, please connect your PC to WIPG-300H (via wired or wireless).

Step 2. Open the web browser and it will redirect to WIPG-300H home page automatically. Or you can enter the default IP address http://192.168.1.1 to access it.

After a moment, the main screen appears as shown in Figure 5-1.

Figure 5-1

The following sections will introduce the detailed instructions of the web UI functions.

5.2. Download

Please follow the steps below to download and execute the WIPG installation program.

Step 1. Click "Download".

Step 2. Choose the WIPG utility for "Windows 7 / 8 / 10" or "Mac OS" and then click the Download button and execute the installation program.

Figure 5-2

Step 3. Follow Installation Wizard instructions to proceed till the installation process is completed. Once

installation is completed, a MirrorOp utility shortcut

will appear on the desktop.

If the "Windows Security Alert" pops up, just press the "Unblock" button to continue the installation.

5.3. Conference Control

This function allows you to host a meeting without the projector cable swapping, and each participant is able to show their own presentation easily. Please follow the steps below to execute Conference Control.

Step 1. Click "Conference Control".

Step 2. Enter the password. The default value is "moderator". Then press the Login button.

Figure 5-3

Step 3. After login, you can see a user list on the screen which indicates the clients who have already logged in to the WIPG utility. There are three columns, "Name", "Play Control" and "IP Address".

There are six buttons:

Play (Full Screen)	Play Split #1 1	Play Split #2 2
Play Split #3 3	Play Split #4 4	Stop

Figure 5-4

5.4. Admin

This function allows you to login web management UI of WIPG-300H. Click "Admin", and enter the password.

The default value is "admin". Then click the Login button or press the Enter key.

Please refer to the following sections for further configuration of the web management UI.

Figure 5-5

Default IP Address: 192.168.1.1

Default Password: admin

After entering the password, the main screen appears as shown in Figure 5-6.

5.4.1. System Status

On this page, you can see the current status and some basic settings of the presentation gateway.

Figure 5-6

Object Description
Model Name	Product model name
Firmware Version	Product firmware version number
Network Status
IP Address	The IP address of WIPG-300H
Subnet Mask	The subnet mask
Default Gateway	The default gateway
Wireless MAC Address	The wireless MAC address
Wired MAC Address	The wired MAC address
Connection Status
Projecting Status	It shows “Waiting for projecting” or “Projecting”.
Total Users	The number of users who has already logged in to WIPG utility
Code	Login code

5.4.2. Device Setup

Figure 5-7

Object Description
Resolution VGA:	SVGA (800x600) / XGA (1024x768)WXGA(1280x768) / WXGA(1280x800)WXGA (1360x768) / WXGA+ (1440x900)UXGA (1600x1200)HDMI:720p (1280x720) / 1080i (1920x1080)1080p (1920x1080)
Code	You can select “Disable”, “Random”, or “Use the following code” to set a specified 4-character number.
IWB USB Port	You can configure the IWB USB port to support “IWB (HID)” device or “Mouse/Keyboard” device.

Note

The default setting of project output port is VGA. However, the HDMI cable will still work if you plug it before powering on the WIPG-300H.

Click the Apply button to make the changes to take effect.

5.4.3. Network Setup

This page is used to configure the parameters for the local area network which connects to the LAN port or wireless interface. Here you may change the setting for IP address, subnet mask, DHCP, etc.

Figure 5-8-1

Setup

The page includes the following detailed fields:

Object Description
IP Setup
Obtain IP address automatically	If you select this option, the WIPG-300H will detect the network environment automatically.■ When WIPG-300H is connected to a LAN that has DHCP server, the clients of WIPG-300H will assign an IP by that server and the built-in DHCP server of WIPG-300H will be disabled.■ When the WIPG-300H is connected to a LAN that does not have any DHCP server, the built-in DHCP server of WIPG-300H will be enabled and the clients of WIPG-300H will obtain IP address by itself.
Use the following IP address	Or you can select this option to use the fixed IP address for WIPG-300H. (Default Settings)
	IP Address	The default value is 192.168.1.1
	Subnet Mask	The default value is 255.255.255.0
	Default Gateway	The default value is 192.168.1.1
	DNS Server	The default value is 192.168.1.1

DHCP Server Setup

Object Description
Auto	Select “Auto” to enable the built-in DHCP server of WIPG-300H. (Default Settings)
	Start IP	The default value is 192.168.1.100
	End IP	The default value is 192.168.1.200
	Subnet Mask	The default value is 255.255.255.0
	Default Gateway	The default value is 192.168.1.10
	DNS Server	The default value is 192.168.1.10
Disable	Or you can select this option to disable the DHCP server of WIPG-300H.

Wireless Setup

Wireless Setup	Wireless LAN ○ Enable ○ Disable	Embedded AP SSID/ NAME WIPG-300H
	SSID Broadcast	○ Enable ○ Disable
	Band	○ 2.4 GHz ○ 5 GHz
	802.11mode	2.4G B/G/N mixed
	Channel	Auto
	Encryption	Disable
	Key	Hide characters
	Channel Bandwidth	○ 20MHz ● Auto

Figure 5-8-2

The page includes the following detailed fields:

Object Description
Wireless LAN	The option for enabling or disabling wireless LAN function
	Enable SSID	You can configure the SSID string here when Wireless LAN is enabled.
SSID Broadcast	The default value is “Enable”.
Band	Select 2.4GHz or 5GHz wireless network.
Channel	If you select “Auto”, the WIPG-300H will scan all of the wireless channels and choose a clear one automatically. Or you can select a fixed channel.
Encryption	The option of wireless security. You can select one of WEP / WPA / WPA2, or disable it.
Key	If Encryption is enabled, you have to set the key according to the encryption mode you selected.
Channel Bandwidth	Select from 20M or Auto (20M/40M)

AP Client Setup

Check the "Enable" radio button to switch WIPG-300H to AP client mode. It can join other access points wirelessly. Besides, the clients can also login WIPG-300H for presentation and surf the Internet via other AP simultaneously.

graph TD
    A["Internet"] --> B["Cable/DSL Modem"]
    B --> C["Staff Office"]
    C --> D["Private AP for employees only"]
    D --> E["Wireless Signal Repeat"]
    E --> F["Guest AP for Presentation and Internet"]
    F --> G["WIPG-300H"]
    G --> H["Wi-Fi Phone"]
    H --> I["Projector"]
    I --> J["Guest Room"]
    J --> K["2.4GHz 802.11n"]

Figure 5-8-3

Ap Client	Connect to Existing AP ○ Enable ● Disable	Existing AP SSID
		Scan
	Encryption	Disable
	Key
		Hide characters
GateKeeper	○ All Pass ○ All Block ○ Internet Only
SNMP	○ Enable ○ Disable

Figure 5-8-4

The page includes the following detailed fields:

Object Description
Connect to Existing AP	The option for enabling or disabling AP client mode. By this feature you can join other Access Points wirelessly. And LAN function will be disabled during AP client mode.
	Existing AP SSID	Enter the existing AP's SSID here when AP client mode is enabled.
Encryption	Choose the wireless security type of the AP you want to join.
Key	Enter the key of the AP you want to join.
GateKeeper	Gatekeeper is designed for ensuring the enterprise network security within WIPG-300H.
	All Pass	Allow the clients of WIPG-300H (guests) to access the whole office network. (Default setting)
	All Block	Block the clients of WIPG-300H (guests) to access the whole office network (LAN).
	Internet only	This option will block the clients of WIPG-300H (guests) from the office network (LAN) but still reserve the Internet connection capability.
SNMP	You can choose enable or disable SNMP function from here.

Click the Apply button to make the changes to take effect.

To enable the WIPG-300H to run as an AP Client to connect to other existing APs wirelessly, please set the wireless band to 2.4GHz and encryption security type to "WPA AES" or "WPA2 AES".

LAN function will be disabled during AP client mode.

5.4.4. OSD Setup

Users can customize their own OSD (on-screen display) standby image.

Figure 5-9

The web page includes the following fields:

Object Description
Restore to default	Restore to the default OSD standby image.
Image File Uploading	Upload the customized OSD standby image. Please refer to remark on screen when select the file.
Device Information	Show all or Hide all the device information on standby screen.When Device Information is set to Hide option, the "Overlay Device Information" & "Screen Saver Setting" will be disabled
Overlay Device Information	Enabling or disabling the device information will be shown on top of projection screen when doing projection.
Screen Saver Settings	Enable or disable the screen saver and also configure the idle time (Minutes). (Default is 5 minutes)

5.4.5. Change Passwords

Users can change the login password. The length of password is up to 8 characters.

Figure 5-10

Click the Apply button to make the changes to take effect.

5.4.6. Reset to Default

This page allows you to reset the current configuration to factory default.

Figure 5-11

Click the Apply button to restore the WIPG-300H to the factory default settings.

5.4.7. Firmware Upgrade

This page allows you to upgrade the WIPG-300H firmware to new version. Please note: DO NOT power off the device during the upload because it may crash the system.

Figure 5-12

If it is necessary to upgrade the firmware, please follow the steps below to operate carefully.

Step 1. First, download the latest firmware image file from PLANET website.

Step 2. Click the Browse button to specify the file you want to upgrade.

Step 3. Click the Upgrade button to start.

Step 4. There will be a warning message shown and countdown counter on the screen.

Please wait while System burns new firmware into your device.

Warning: It needs to take 1\~3 minutes to burn the file you transferred into flash memory. During this period, any interrupt such as shut down or reboot the system will cause system crash!!

Update Progress: : 15%

Step 5. After a few minutes, a complete message will show on the screen.

Step 6. Power off the WIPG-300H and then power on it again.

Step 7. Login the web UI, and click Reset to Default to take effect.

New firmware versions posted at the website of PLANET Technology can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.

When you upgrade its firmware, you may lose its current configurations. Do not turn off the WIPG-300H while the firmware is being upgraded; otherwise, the WIPG-300H may be damaged.

5.4.8. Webslides Setup

Click on "WebSlides Setup" option and you can: "Adjust Auto Refresh Interval", or activate "Access Password Control" Please pay attention to the note for information.

Figure 5-13

5.4.9. Reboot System

Press Reboot to reboot system. Please wait for a few minutes and reload web page again.

Figure 5-14

Click the Reboot button to restart the WIPG-300H.

Appendix A: Configuring the PCs

In this section, we'll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter's manual if needed.

1. Install TCP/IP component

1) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window.
3) Right-click the icon shown below and select Properties on the prompt page.

Figure A-1

4) On the prompt page shown below, double-click on the Internet Protocol (TCP/IP).

Figure A-2

5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.

Now you have two ways to configure the TCP/IP protocol below:

Setting IP address automatically

Select Obtain an IP address automatically, and then Obtain DNS server automatically, as shown in the Figure below:

Figure A-3

Setting IP address manually

1 Select Use the following IP address radio button.
2 If the device's LAN IP address is 192.168.1.1, type in IP address 192.168.1.x (x is from 2 to 254), and Subnet mask 255.255.255.0.
3 Type the device's LAN IP address (the default IP is 192.168.1.1) into the Default gateway field.
4 Select Use the following DNS server addresses radio button. In the Preferred DNS Server field you can type the DNS server IP address which has been provided by your ISP

Figure A-4

Now click OK to keep your settings.

Appendix B: FAQ

FAQ1 : How to reset the WIPG-300H to factory default

[ANSWERS]

1) Power off the WIPG-300H.

2) Press and hold the button with paper clip, and then plug in the DC jack of the AC adapter to power on WIPG-300H. After 10\~15 seconds, you can release the button.

3) Now, you should be able to login the WIPG-300H by default setting. (Default username and password are both "admin".)

FAQ 2: How to use WIPG-300H to output the screen to the projector or LCD via HDMI cabling

[ANSWERS]

You can switch the output interface through the web UI. The default setting is VGA. However, if you want to use HDMI interface directly without switching:

(1) Plug the HDMI connector and turn on the projector or LCD first.
(2) Then just power on the WIPG-300H to achieve it.

EC Declaration of Conformity

English	Hereby, PLANET Technology Corporation, declares that this 802.11n Wireless Presentation Gateway is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.	Lietuviškai	Šluo PLANET Technology Corporation,, skelbia, kad 802.11n Wireless Presentation Gateway tenkina visus svarbiausius 2014/53/EU direktyvos reikalavimus ir kitas svarbias nuostatas.
Česky	Společnost PLANET Technology Corporation, tímto prohlašuje, že tato 802.11n Wireless Presentation Gateway splňuje základní požadavky a další příslušná ustanovení směrnice 2014/53/EU.	Magyar	A gyártó PLANET Technology Corporation, kijelenti, hogy ez a 802.11n Wireless Presentation Gateway megfelel az 2014/53/EU irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Dansk	PLANET Technology Corporation, erklærer herved, at følgende udstyr 802.11n Wireless Presentation Gateway overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU	Malti	Hawnhekk, PLANET Technology Corporation, jiddikjara li dan 802.11n Wireless Presentation Gateway jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU
Deutsch	Hiermit erklärt PLANET Technology Corporation, dass sich dieses Gerät 802.11n Wireless Presentation Gateway in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 2014/53/EU befindet". (BMWi)	Nederlands	Hierbij verklaart, PLANET Technology orporation, dat 802.11n Wireless Presentation Gateway in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU
Eesti keeles	Käesolevaga kinnitab PLANET Technology Corporation, et see 802.11n Wireless Presentation Gateway vastab Euroopa Nõukogu direktiivi 2014/53/EU põhinõuetele ja muudele olulistele tingimustele.	Polski	Niniejszym firma PLANET Technology Corporation, oświadcza, že 802.11n Wireless Presentation Gateway spełnia wszystkie istotne wymogi i klauzule zawarte w dokumencie „Directive 2014/53/EU”.
Ελληνικά	ME THN ΠΑΡΟΥΣΑ , PLANET Technology Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 802.11n Wireless Presentation Gateway ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU	Português	PLANET Technology Corporation, declara que este 802.11n Wireless Presentation Gateway está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU.
Español	Por medio de la presente, PLANET Technology Corporation, declara que 802.11n Wireless Presentation Gateway cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU	Slovensky	Výrobca PLANET Technology Corporation, týmto deklaruje, že táto 802.11n Wireless Presentation Gateway je v súlade so základnými požiadavkami a dálšimi relevantnými predpismi smernice 2014/53/EU.
Français	Par la présente, PLANET Technology Corporation, déclare que les appareils du 802.11n Wireless Presentation Gateway sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU	Slovensko	PLANET Technology Corporation, s tem potrjuje, da je ta 802.11n Wireless Presentation Gateway skladen/a z osnovnimi zahtevami in ustreznimi določili Direktive 2014/53/EU.
Italiano	Con la presente, PLANET Technology Corporation, dichiara che questo 802.11n Wireless Presentation Gateway è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU.	Suomi	PLANET Technology Corporation, vakuuttaa täten että 802.11n Wireless Presentation Gateway typpinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Latviski	Ar šo PLANET Technology Corporation, apliecina, ka šī 802.11n Wireless Presentation Gateway atbilst Direktīvas 2014/53/EU pamatprasībām un citiem atbilstošiem noteikumiem.	Svenska	Härmed intygar, PLANET Technology Corporation, att denna 802.11n Wireless Presentation Gateway står i överensstämmelse med de væsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 2014/53/EU.