Roar Plus - Pregnant HP - Free user manual and instructions

Product Type	Portable Bluetooth Speaker
Brand	HP
Model	Roar Plus
Color	Black
Bluetooth Version	4.2
Wireless Range	Up to 10 meters
Audio Output Power	20W
Frequency Response	80 Hz – 20 kHz
Water Resistance	IPX7
Battery Capacity	2200 mAh
Playback Time	Up to 12 hours
Charging Port	Micro USB
Audio Inputs	Bluetooth, AUX (3.5mm), MicroSD card
FM Radio	Yes
Handsfree Calling	Yes (built-in microphone)
Dimensions (W x H x D)	180 x 75 x 75 mm
Weight	540 g
Included Accessories	Micro USB charging cable, AUX cable, user manual
Speaker Type	Full-range driver with passive radiator
Controls	Power, Volume +/-, Play/Pause, Track skip, Mode
Material	Fabric and rubber
Cleaning Instructions	Wipe with a soft, dry cloth
Safety Instructions	Do not expose to extreme temperatures or moisture beyond IPX7 rating
Spare Parts Availability	Not available from manufacturer
Repairability	Not user-serviceable; contact HP support for repairs

Frequently Asked Questions - Roar Plus HP

How do I pair the HP Roar Plus with my phone via Bluetooth?

Turn on the speaker and press the Bluetooth button. On your phone, enable Bluetooth and select 'HP Roar Plus' from the list. If prompted, confirm pairing. The speaker will emit a tone when connected.

Can I use the HP Roar Plus while it's charging?

Yes, you can use the speaker while it is charging. However, for optimal battery health, it is recommended to occasionally fully discharge and recharge the battery.

How do I reset the HP Roar Plus speaker?

To reset, press and hold the Power button and the Volume Up button simultaneously for about 5 seconds until the speaker turns off and restarts. This restores factory settings.

What does the IPX7 rating mean for the HP Roar Plus?

IPX7 means the speaker can be submerged in water up to 1 meter deep for up to 30 minutes without damage. It is resistant to rain, splashes, and can be used near pools.

How long does it take to fully charge the HP Roar Plus?

Full charging takes approximately 3-4 hours using a standard 5V/1A charger. Using a higher current charger may reduce charging time but is not recommended.

Can I use the HP Roar Plus as a speakerphone?

Yes, the HP Roar Plus has a built-in microphone for handsfree calling. When connected via Bluetooth, you can answer incoming calls by pressing the Play/Pause button.

How do I play music from a microSD card?

Insert a microSD card (up to 32GB) into the slot. Press the Mode button until the display shows 'SD' or 'Card'. The speaker will automatically play the audio files from the card.

What is the best way to clean the HP Roar Plus?

Unplug the speaker and remove any cables. Wipe the exterior with a soft, damp cloth. Do not use harsh chemicals or abrasive materials. Avoid getting moisture into the ports.

How do I enable FM radio on the HP Roar Plus?

Press the Mode button repeatedly until 'FM' appears on the display. The speaker will automatically scan for stations. Use the Volume buttons to tune to the desired frequency.

What should I do if the HP Roar Plus does not turn on?

First, ensure the speaker is charged. Connect it to a power source and charge for at least 30 minutes. If still unresponsive, try resetting the speaker (Power + Volume Up). If the issue persists, contact HP support.

USER MANUAL Roar Plus HP

HP Roar Plus Speaker

Other Features

© Copyright 2014 Hewlett-Packard Development Company, L.P.

Microsoft, Windows, and Windows Vista are U.S. registered trademarks of the Microsoft group of companies. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

First Edition: October 2014

Document Part Number: 791395-001

Table of contents

1 Pairing the speaker to your device .... 1
2 Pairing the speaker to your Windows® computer 2
Windows 7 and Windows Vista® 2
Windows 8 ...... 2
3 Pairing the speaker to a second device 3
4 Setting up True Wireless Stereo 4
5 Button features 5
Talk button 5
Muting a call 5
Resetting the speaker 5
6 Using your charger 6

1 Pairing the speaker to your device

1. Connect the HP Roar Plus Speaker to power and make sure that it is charged. The power button light blinks amber while the speaker is charging.
2. Press the power button. The speaker starts in pairing mode. The power button light blinks white while the speaker is on and in pairing mode.
3. On your device, connect to the speaker using Bluetooth®. See your device's documentation for instructions on making a Bluetooth connection.

When you next turn on the speaker, it automatically attempts to connect to one of the last six Bluetooth devices paired to the speaker.

2 Pairing the speaker to your Windows® computer

Windows 7 and Windows Vista®

To pair the speaker using Windows 7 or Windows Vista:

1. Make sure that your computer's Bluetooth function is turned on.
2. Click Start > Control Panel.
3. Windows 7: Under the Hardware and Sound section, click Add a device.

- or -

Windows Vista: Under the Hardware and Sound section, click Add a Wireless Device under Bluetooth Devices.

1. Turn on the speaker, which should start in pairing mode.

In a few moments, the speaker should appear in the list of discovered Bluetooth devices.

1. Select the speaker, and then click Continue to begin the pairing process.

Windows 8

To pair the speaker using Windows 8:

1. Make sure that your computer's Bluetooth function is turned on.
2. Press the Windows key + c to display the charms on the right side of the Windows 8 screen.
3. Click Settings.
4. Click Change PC settings on the bottom right of the screen.
5. Click Devices.
6. Click Add a device.
7. Turn on the speaker, which should start in pairing mode. In a few moments, the speaker should appear in the list of discovered Bluetooth devices.
8. Select the speaker, and then click Continue to begin the pairing process.

3 Pairing the speaker to a second device

After successfully connecting to one device, you can connect to a second device.

1. On your currently connected device, temporarily disconnect from the speaker.
2. When the light blinks white, pair the second device to the speaker. See your device's documentation for instructions on making a Bluetooth connection.
3. On your first device, start the Bluetooth pairing process. Your device automatically connects to the speaker.

TIP: To start music, press the pause button on the first device, and then press the play button on the second device. To switch control or to share songs, press pause on the second device, and then press play on the first device.

4 Setting up True Wireless Stereo

If you have two HP Roar Plus Speakers and a Bluetooth device, you can use True Wireless Stereo (TWS).

1. Power on one of the speakers.

2. Pair the Bluetooth device to this speaker.

3. Power on the second speaker.

4. Press and hold the talk button and the back button on the first speaker to make it the sender.

5. When the first speaker says, "Connect me," set the second speaker as the receiver by pressing and holding the talk button and the forward button.

6. When the speakers say, "Connected," they are in stereo mode. It takes about seven seconds for the sender to connect to the receiver.

To end stereo mode, turn off the receiver. The next time you turn on the speakers, they will attempt to pair with each other.

To disconnect the TWS pairing, turn off the receiver and then press and hold the talk button for six seconds. All previous pairing information is cleared from the speaker.

5 Button features

See the Quick Setup Poster included in the speaker packaging for an overview of the speaker buttons. This chapter covers some special features.

Talk button

To answer a call:

1. Pair a phone or phone app to the speaker using Bluetooth.

2. When the phone rings, press the talk button.

To answer a second call, press the talk button twice. To end a call, press and hold the talk button.

Muting a call

To mute a call, press the talk button. To unmute a call, press the talk button again.

Resetting the speaker

Use the following procedure to disconnect paired Bluetooth devices from the speaker.

▲ Press and hold the talk button for six seconds. The light blinks five times, alternating white and amber.

All previous pairing information is cleared from the speaker.

6 Using your charger

To charge your speaker:

1. Connect the micro USB end of the included micro USB-to-USB cord to the micro USB port on the speaker.
2. Connect the USB end of the cord to the included AC adapter, and then connect the AC adapter to a wall plug.
3. or -
   Connect the USB end of the cord to a powered USB port on a device such as a computer or docking station.

The power button light blinks amber while the speaker is charging. When the speaker is fully charged, the light is off if the speaker is turned off or the light is solid white if the speaker is turned on.

To charge a device using your speaker:

1. Connect the device to the device charging cable.
2. Connect the USB end of the device charger to the USB port on the speaker.

NOTE: Charging a device decreases the music playback time.

TIP: To charge an iPhone 4, press the talk button after connecting the charger to the speaker.