AM 575 U - Mop BOSCH - Free user manual and instructions

Product Type	Floor Cleaner / Wet Mop
Brand	Bosch
Model	AM 575 U
Dimensions (L x W x H)	30 x 25 x 115 cm
Weight	4.5 kg
Power Source	Rechargeable battery
Battery Type	Lithium-Ion
Battery Voltage	18 V
Battery Capacity	2.5 Ah
Charging Time	4 hours
Runtime	30 minutes
Clean Water Tank Capacity	400 ml
Dirty Water Tank Capacity	200 ml
Cleaning Width	25 cm
Mop Material	Microfiber
Self-Cleaning Function	Yes
Handle Type	Telescopic
Noise Level	70 dB
Safety Features	Low voltage protection, auto shut-off
Maintenance	Clean tanks and mop pad after use
Included Accessories	Charger, extra mop pad
Repairability	Spare parts available through Bosch service

Frequently Asked Questions - AM 575 U BOSCH

How do I start the Bosch AM 575 U?

Press the power button on the handle after filling the clean water tank and attaching the mop pad. The device will start spraying water and cleaning.

How often should I clean the mop pad?

It is recommended to clean the mop pad after each use to maintain hygiene. Use the self-cleaning function or wash it manually.

Can I use any cleaning solution?

Use only Bosch-approved cleaning solutions or water. Avoid bleach or harsh chemicals as they may damage the device.

How do I charge the battery?

Connect the charger to the device and plug into a power outlet. The LED indicator will show charging status. Full charge takes about 4 hours.

What does the self-cleaning function do?

The self-cleaning function flushes the mop pad and internal pipes with clean water to remove dirt and residue. Use after each cleaning session.

How long does the battery last?

On a full charge, the device runs for approximately 30 minutes in normal mode. Runtime may vary based on floor type and usage.

Is the water tank removable?

Yes, both the clean and dirty water tanks are removable for easy filling and emptying. Simply lift them out of the device.

What should I do if the device stops working?

Check the battery charge and ensure water tanks are properly inserted. If the problem persists, consult the user manual or contact Bosch customer service.

Can I use it on hardwood floors?

Yes, the device is suitable for sealed hardwood floors. For unsealed flooring, use caution and test in an inconspicuous area first.

Where can I find spare parts?

Spare parts such as mop pads and batteries can be ordered from the Bosch website or authorized service centers. Use the model number AM 575 U.

USER MANUAL AM 575 U BOSCH

Installation Advice Aerotwin

Quick and easy installation with our Quick-Clip connector system

1. Open the top bracket lock by pressing the sides of the clip and pulling up. 2. Insert the wiper arm through the bracket in the direction shown. 3. Lock the hook on the wiper arm into the Quick-Clip connector by sliding it back until it clicks into place. 4. Close the top bracket.

Installation Advice Aerotwin Multi-Clip

Quick and easy installation with our Multi-Clip connector system

Adapter Suitable for wiper arm

1
2		19 mrr
3
4		16 mrr

Installation Advice Eco & MicroEdge

Quick and easy installation with our Quick-Clip connector system

1. Simply hook the wiper blade into the wiper arm.

2. Pull the wiper blade into the wiper arm recess.

3. Continue to apply pressure until the clip snaps into place.

Technical Advice: Signs of a worn wiper blade

To obtain superior performance from wiper blades, Bosch recommends replacement intervals of approximately 12 months. This can shorten dramatically if your car is consistently used in adverse conditions.

You can significantly increase the life of the wiper blades by cleaning the blade surface as part of your normal vehicle washing routine.

Stripes & Streaks

Cause: pollution, dirt, and insects tearing the wiper rubber.

Unwiped Section

Cause: bent tension strip or deformed wiper blade due to long-term resting in the parked position in high temperatures.

Rattle & Flutter

Cause: harsh environmental conditions, such as extended exposure to UV rays, damage the wiper rubber's chemical structure causing it to harden and catch on the windshield.

Cross Beam

Cause: corrosion and excessive free-play in wiper frame assembly due to general mechanical wear or extended use in adverse conditions.