Metal Zone MT-2WÙ - Guitar amplifier BOSS - Free user manual and instructions

Product Type	Guitar Distortion Pedal
Brand	Boss
Model	Metal Zone MT-2W (Waza Craft)
Dimensions	73 mm x 129 mm x 59 mm (2.9 x 5.1 x 2.3 inches)
Weight	440 g (0.97 lbs)
Power Supply	9V DC (PSA series adapter) or 6 x AA batteries
Current Draw	70 mA
Controls	Level, Distortion, EQ (Low, Mid, High), Presence
Input Impedance	1 MΩ
Output Impedance	1 kΩ
Connectors	Input (1/4"), Output (1/4"), AC Adapter (DC Jack)
Indicator	Check indicator (battery check/status)
Bypass	True bypass (switching)
Frequency Response	20 Hz - 20 kHz
Waza Craft Features	Enhanced circuit, premium components, selectable custom mode
Construction	Metal chassis
Accessories	Owner's manual, leaflet, rubber foot
Cleaning	Wipe with dry cloth; avoid solvents
Safety Precautions	Use only specified power supply; avoid moisture
Spare Parts & Repairability	Parts available through Boss service centers; user-replaceable battery

Frequently Asked Questions - Metal Zone MT-2WÙ BOSS

How do I power the MT-2W pedal?

You can power the MT-2W using a 9V DC power supply (Boss PSA series) or six AA batteries. The current draw is 70 mA.

What is the difference between the MT-2W and the standard MT-2?

The MT-2W is a Waza Craft version with upgraded components, a custom mode switch for extended tone shaping, and improved sound quality.

How do I engage true bypass?

The MT-2W features true bypass switching. When the effect is off, the signal passes through without any coloration.

What do the EQ controls do?

The pedal has a 3-band EQ with Low, Mid, and High controls, plus a Presence knob. These allow precise shaping of your distorted tone.

Can I use the MT-2W with bass guitar?

Yes, the MT-2W can be used with bass, though it is designed for guitar. The EQ allows you to dial in bass-friendly tones.

What is the custom mode switch for?

The custom mode switch, located inside the battery compartment, offers alternative EQ and distortion characteristics for more versatility.

How do I replace the battery?

Remove the screws on the bottom plate, open the compartment, replace the six AA batteries ensuring correct polarity, and close the plate.

What type of cable should I use?

Use standard 1/4-inch instrument cables. The input impedance is 1 MΩ, so it works well with most guitars.

Can I daisy-chain the MT-2W with other pedals?

Yes, but ensure the power supply can provide enough current (70 mA). Avoid using non-isolated daisy chains to reduce noise.

How do I clean the pedal?

Wipe the exterior with a soft, dry cloth. Do not use solvents, alcohol, or abrasive cleaners.

USER MANUAL Metal Zone MT-2WÙ BOSS

Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.

Main Features

• This is a WAZA CRAFT series effect pedal crafted with a high-quality analog original circuit design.
• This unit produces a wide range of harmonically rich and powerful high-gain distortion sounds.
• This unit also includes a Custom setting providing an even broader range of dynamics and response.

Panel Descriptions

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series; sold separately).

* Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet of the correct voltage.

* If the AC adaptor is connected while a battery is installed, the power supply is drawn from the AC adaptor.

* Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet of the correct voltage. * If the AC adaptor is connected while a battery is installed, the power supply is drawn from the AC adaptor.

AC Adaptor (PSA series; sold separately)

EQUALIZER LOW knob

This knob controls the tone of the effect sound at lower frequencies. Rotating the knob clockwise boosts the lower frequencies, while rotating it counterclockwise cuts the lower frequencies. The lower frequencies have a variable range of ± 15 dB.

EQUALIZER HIGH knob

This knob controls the tone of the effect sound at higher frequencies. Rotating the knob clockwise boosts the higher frequencies, while rotating it counterclockwise cuts the higher frequencies. Higher frequencies have a variable range of ±15 dB.

LEVEL knob

This knob adjusts the volume of the effect sound.

* No sound will be heard when this knob is rotated completely counterclockwise.

OUTPUT jack

Use this 1/4" output jack to connect to the input of your guitar amplifier or the input of additional effect unit.

Guitar Amplifier

Pedal switch

This switch turns the effects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the battery.

* For instructions on changing the battery, refer to "Changing the Battery."

CHECK indicator

This indicator shows whether an effect is ON/OFF, and doubles as the Battery Check indicator. The indicator lights when an effect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace the battery when the LED is dim or does not light. For instructions, refer to "Changing the Battery."
* The CHECK indicator shows whether the effect is on or off, and indicates the different functions. It does not indicate whether the power to the device is on or not.

EQUALIZER MID FREQ knob

This knob adjust the frequency of the Middle knobs gain. Rotating the knob clockwise increases the frequency center point. At Max the frequency center is 5 kHz. Rotating the knob counterclockwise decreases the frequency center point. At Minimum the frequency center is 200 Hz.

EQUALIZER MIDDLE knob

This knob boosts or cuts the frequency you set with the EQUALIZER MID FREQ knob. Rotating the knob clockwise boosts the level of the middle frequencies, while rotating it counterclockwise cuts the level of the middle frequencies.
* When the EQUALIZER MIDDLE knob is set to the center position, the EQUALIZER MID FREQ knob does not affect the sound.

DIST knob

Rotating the knob clockwise increases the gain and distortion effect.
* If you set this knob too high, the noise will increase and oscillation may occur.

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another effects unit).
* The INPUT jack also serves as the power switch. Power is turned on whenever a plug is inserted into the INPUT jack, and is turned off when the plug is disconnected. When not using the unit, you should disconnect any cord connected to the INPUT jack.

Mode switch
Switches the sound variation.

S (Standard)	Reproduces the original MT-2 sound by a newly crafted all analog circuit.
C (Custom)	Produces a custom sound which is fine-tuned for broader range of dynamics and response.

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
* Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn off the power to your guitar amp first.
* Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

Use of Battery

* The life of the included battery may be limited as its primary purpose was for testing during assembly.
If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (supplied on a separate sheet).
* When operating on battery power only, the unit's indicator will become dim when battery power gets too low. Replace the battery as soon as possible.
* Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward. * The pedal can be opened without detaching the thumbscrew completely.

1. Remove the old battery from the battery housing, and remove the s
2. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery's polarity (+ versus -).
3. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.
4. Finally, hold down the pedal while tightening the thumbscrew into the guide bush hole.

Main Specifications

BOSS MT-2W: Metal Zone

Nominal Input Level -20 dBu
Input Impedance	1 MΩ
Nominal Output Level -20 dBu
Output Impedance	1 kΩ
Recommended Load Impedance	10 kΩ or greater
Power Supply	DC 9 V: Alkaline battery (9 V, 6LR61),Carbon-zinc battery (9 V, 6F22), AC adaptor(sold separately)
Current Draw	35 mA* Expected battery life under continuous use:Alkaline battery: Approx. 18 hoursCarbon-zinc battery: Approx. 7 hoursThese figures will vary depending on the actual conditions of use.
Dimensions	73 (W) x 129 (D) x 59 (H) mm2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight(including battery)	440 g1 lb
Accessories	Owner's Manual, Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”), Alkaline battery (9 V, 6LR61)
Option(sold separately)	AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms
* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.
* Roland, BOSS, METAL ZONE, and 技WAZA CRAFT are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.