GBS 305 UG - Saw Güde - Free user manual and instructions

USER MANUAL GBS 305 UG Güde

Industrial machine with blue frame and black base, no visible text or symbols on the device itself

GBS 305 UG

54991

GÜDE GmbH & Co. KG

Birkichstrasse 6

74549 Wolpertshausen

Deutschland

Güde

ENGLISH Please read the instructions carefully before starting the machine.

Scanned document with placeholder text and a blue 'OK' button, likely a software interface or report.

3D mechanical assembly diagram showing a presser with internal components and motor (no text or labels visible)

3D rendering of a rectangular electronic component with grid lines and two metallic pins (no text or symbols visible)

Mechanical component with a yellow tip and five separate T-shaped pins below (no text or symbols visible)

3D rendering of a mechanical lever assembly with a green and white component (no text or symbols visible)

1

Four identical rectangular electronic components with mounting holes, shown in side-by-side alignment (no text or symbols)

4

2
24 x

3

D	Montage	SLO	Montaža
GB	Assembly	HR	Montaža
F	Assemblage	BG	Монтаж
I	Montaggio	RO	Montaj
NL	Montage
CZ	Montáž
SK	Montáž
H	Szerelés

1

2-3

D	Inbetriebnahme	SLO	Uvedba v pogon
GB	Starting-up the machine	HR	Puštanje u rad
F	mise en service	BG	Пускане в действие
I	Messa in funzione	RO	Punerea în funcțiune
NL	Inbedrijfstelling
CZ	Uvedení do provozu
SK	Uvedenie do prevádzky
H	Üzembe helyezés

2

4 - 9

D	Betrieb	SLO	Delovanje
GB	Operation	HR	Rad
F	Fonctionnement	BG	Pábota
I	Esercizio	RO	Functionare
NL	Gebruik
CZ	Provoz
SK	Prevádzka
H	Üzemeltetés

3

10-11

1	D	Montage	SLO	Montaža
	GB	Assembly	HR	Montaža
	F	Assemblage	BG	Монтаж
	I	Montaggio	RO	Montaj
	NL	Montage
	CZ	Montáž
	SK	Montáž
	H	Szerelés

1 1 2 3 4 5

2 1 2 3 4 5 24x 2

3 4x 3 3

D	Montage	SLO	Montaža
GB	Assembly	HR	Montaža
F	Assemblage	BG	Монтаж
I	Montaggio	RO	Montaj

NL Montage

CZ Montáž

SK Montáž

H Szerelés

4 4

Technical line drawing of a metal frame structure with a folded panel and an arrow indicating direction (no text or symbols)

4 4x

3D mechanical setup with a vertical presser machine and motor, no visible text or symbols

1	D	Montage	SLO	Montaža
	GB	Assembly	HR	Montaža
	F	Assemblage	BG	Монтаж
	I	Montaggio	RO	Montaj
	NL	Montage
	CZ	Montáž
	SK	Montáž
	H	Szerelés

Mechanical assembly diagram showing a motor, clamping mechanism, and mounting plate (no text or symbols)

Industrial machine assembly diagram showing internal components and a close-up view of a motor assembly (no text or labels visible)

D	Montage	SLO	Montaža
GB	Assembly	HR	Montaža
F	Assemblage	BG	Монтаж
I	Montaggio	RO	Montaj

NL Montage

CZ Montáž

SK Montáž

H Szerelés

1

8 7

9 7

10 9 8

10 11

2	D	Bandgeschwindigkeit einstellen	SLO	Nastavite hitrost traku
	GB	Adjust the belt speed	HR	Podesite brzinu trake
	F	Réglez la vitesse du ruban	BG	Pegyliрайte скоростта на лентата
	I	Impostare la velocità del nastro	RO	Reglați viteza benzii
	NL	Bandsnelheid instellen
	CZ	Nastavte rychlost pásu
	SK	Nastavte rychlost pásu
	H	Állítsa be a szalagsebességet

graph LR
    A[" "] -->|m/min| B[" "]
    B -->|m/min| C[" "]
    C --> D[" "]

Technical diagram of a mechanical device with an open lid and internal structure, showing a close-up view of a lock mechanism (no text or symbols present)

Technical diagram of a mechanical device with a rotating wheel and housing, showing no text or symbols.

3

4

5

Simple illustration of a black rounded rectangle and two gray rectangular blocks on a white background (no text or symbols)

Technical line drawing of a mechanical device with a rotating wheel and directional arrow (no text or symbols)

8

2

D MikroschalterGB MicroswitchF Micro-interrupteurI MicrointerruttoreNL MicroschakelaarCZ MikrospínačSK MikrospínačH Mikrokapcsoló

SLO Mikro stikaloHR Mikro prekidačBG MikропревключвателRO Microcomutator

Technical line drawing of a mechanical device with two wheels and a central shaft (no text or symbols)

Technical diagram of a mechanical device with a green checkmark indicating a specific part, no readable text or symbols present.

Technical illustration of a mechanical testing machine with a green checkmark indicating a specific component (no text or symbols present)

GB Adjust the saw belt tension

F Réglez la tension du ruban de scie I Impostare la tensione della lama

NL Zaagbandspanning instellen

Technical diagram of a 3D printing machine with labeled components and measurement annotations including 1-2 mm scale and checkmark.

2	D	Gehrung einstellen	SLO	Nastavljanje kota
	GB	Set mitre	HR	Podesite kut rezanja
	F	Régler l'onglet	BG	Haстройване на скосяването
	I	Impostare la bisellatura	RO	Reglare oblicitate
	NL	Verstek instellen
	CZ	Nastavte zkosení
	SK	Nastavte úkos
	H	Gérvágás beállítása

45° 0

90° ✓

D Parallelanschlag

H Párhuzamos ütköző

GB Rip fence

SLO Stransko vodilo

F Butée parallèle

HR Rip ograda

Battuta parallela

BG Rip orрада

Mechanical assembly diagram showing a machine with rollers and a lock mechanism, no visible text or symbols

A X X

B X X

2	D	Parallelanschlag	H	Párhuzamos ütközö
	GB	Rip fence	SLO	Stransko vodilo
	F	Butée parallèle	HR	Rip ograda
	I	Battuta parallela	BG	Rip orpađa
	NL	De parallelle aanslag	RO	Rip gard
	CZ	Podélné pravítko
	SK	Ochranné zariadenie na pozdížne rezanie

3D technical illustration of a mechanical assembly with conveyor and actuator (no visible text or symbols)

TIP

GB Cutting height setting

Technical diagram of a mechanical assembly with labeled parts and dimensional annotations in millimeters

	D	Betrieb	SLO	Delovanje
	GB	Operation	HR	Rad
	F	Fonctionnement	BG	Pábota
	I	Esercizio	RO	Functionare
	NL	Gebruik
	CZ	Provoz
	SK	Prevádzka
	H	Üzemeltetés

START 1 2 STOP 3

DE Absaugung

GB dust collection

Technical diagram showing mechanical assembly with labeled components and directional arrows (no readable text or symbols)

2 1 2

Technical diagram of a mechanical device with a wheel and shaft assembly (no visible text or symbols)

Technical diagram of a mechanical assembly with a wheel and shaft, showing no text or symbols

D Sägebandwechsel

GB Saw belt replacement

HR Zamjena trake pile

Technical line drawing of a mechanical device with visible gears and shafts, no text or symbols present.

4	D	Stützlager einstellen	SLO	Nastavitev podpornega ležaja.
	GB	Adjust the support bearing	HR	Namještanje potpornog ležaja
	F	Régler le coussinet de support.	BG	Pegylirané na oporníra lagep
	I	Regolare il cuscinetto di supporto.	RO	Reglare lagäre de sprijin
	NL	Steunlagers instellen
	CZ	Nastavte opěrná ložiska
	SK	Nastavte oporné ložiská
	H	Támcsapágy beállítása

Technical diagram of a mechanical device with numbered components and labeled parts, including lock symbols and directional arrows.

D	Sägebandführung einstellen	SLO	Nastavite napeljavo traku žage
GB	Adjust the saw belt guide	HR	Podesite vodilicu trake pile
F	Réglez le guidage du ruban de scie	BG	Настройте преминаването на лентата на циркуляра
I	Impostare la guida della lama
NL	Zaagbandgeleiding instellen	RO	Grglați gjidajul benzii ferăstrăului
CZ	Nastavte vedení pásu pily
SK	Nastavte vedenie pásu píly
H	Állítsa be a fûrészszalag vezetését

Technical diagram of a mechanical device with labeled parts and directional arrows indicating movement or assembly.

	D	Transport	SLO	Transport
	GB	transport	HR	Prijevoz
	F	Transport	BG	Транспортиране
	I	Trasporto	RO	Transportul
	NL	Transport
	CZ	Přeprava
	SK	Transport
	H	Szállítás

3D mechanical assembly diagram showing a presser machine with tool handle and control panel (no text or symbols visible)

3D mechanical assembly diagram showing a presser or actuator with internal components and no visible text or symbols

Illustration of a person using a mechanical device to lift a tower, with a red X mark indicating no text or symbols.

Diagram illustrating a mechanical assembly process with two human figures and a magnified inset showing a device's internal structure.

Technische Daten

Read and understand the operating instructions before using the appliance. Familiarise with the

control elements and how to use the appliance properly. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties.

The operator is responsible for accidents or risks to third parties.

Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.

In case of any doubts about connection and operation refer please to our customer center

Specified Conditions Of Use

The band use is allowed for cutting wood or soft plastics. Only manufacturer-recommended bands are allowed for use. Firewood cutting is prohibited.

Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.

It is strictly prohibited to disassemble, modify I purposely remove the protective equipment on unit and fit other protective equipment instead.

Even when the device is used properly and all safety regulations are complied with, there still may be some residual risks.

• noise emissions
• dust emissions
  • vibrations to hand and arms
• Danger of burns
  Tool and workpiece heat up during operation.
• Risk of injury
  Sharp tools and workpiece edges

Emergency procedure

Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. If you seek help, state the following pieces of information: 1. Accident site, 2. Accident type, 3. Number of injured persons, 4. Injury type(s)

Symbols

WARNING/CAUTION!

WARNING - Read the operating instructions to reduce the risk of injury.

Wear eye protective goggles! Wear ear protectors!

Wear gloves!

Unplug the machine before any work on it.

Always keep hands away from the path of the saw blade.

Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.

Class II tool.

CE marking

General safety information

WARNING!

When using electric tools the following general safety instructions must be obeyed to protect yourself from electric shocks, injury and fire risks.

Read all these instructions before using this electric tool and keep the safety instruction in a safe place.

Keep your work area clean and tidy. Untidy workplaces and workbenches increase the risk of accidents and injuries.

Do not expose the appliance to rain and do not use it in wet or moisture conditions.

Provide adequate lighting or good lighting conditions when working with the machine.

Do not work with electric tools in conditions with flammable liquids, gases or dust. Electric tools produce sparks able to ignite dust or fumes.

Protect yourself from electric shock.

Avoid body contact with earthed objects (for example pipes, radiators, electric stoves and cooling units). There is an increased risk of electric shock if your body is earthed.

Keep children and bystanders away while operating a power tool. Do not touch the electric tool or the cable. When not concentrated, you may lose control over the machine.

Ensure that you store electric tools in a safe place. Tools which are not in used must be stored in a dry place as high as possible out of the reach of children or in an inaccessible place.

Do not overload the machine. Use appropriate electric tools for your work. Working with appropriate electric tools is better and safer when within the specified power range. They will work better and more safely in the specified power range. Do not use low-power machines for heavy work.

Do not use the electric tool for purposes for which it is not designed. For example, do not use a manual circular saw for cutting branches or logs.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. We recommend that you wear non-slip shoes when working outdoors. Wear a hairnet if you have long hair.

Use protective equipment which fit you. Wear safety goggles and ear protection at all times. A dust mask or respirator is also required. Wear tight-fitting gloves at all times when handling sharp blades and saw blades,

If dust exhausters and catchers are to be installed, make sure they are fitted and used properly. Using a dust exhauster may reduce the exposure to dust.

Do not use the cable in conflict with its designation, to carry or hang electric tools or to pull the plug out of socket. Protect the cable against high temperatures, oil, sharp edges or moving parts of the machine. Damaged or entangled cables increase the risk of electric shock.

Only workpieces that have a contact surface for safe guiding on the work table may be worked on. Round materials may only be cut with suitable holding brackets.

Avoid any abnormal body posture. Provide good stability and keep balance at all times. By this, electric tools are better controlled in unexpected situations.

Treat electric tools carefully. Check whether the moving parts work perfectly and do not drag, whether not broken or damaged to such an extent that functioning of electric tools could be affected. Have any damaged parts repaired before using the machine. Poor maintenance of electric tools is a cause of many injuries.

Keep the cutting tools sharp and clean. Carefully treated cutting tools with sharp edges get stuck less often and are easier to guide.

Follow the instructions for lubricating and changing tools.

Check the connection cable on the electric tool at regular intervals and have it replaced by an expert if it is damaged.

Check the extension cables at regular intervals and replace them if they are damaged.

Keep the handles dry, clean and free of oil and grease.

Pull the plug out of the socket and/or remove the battery when the tool is not in use before you make machine settings or change accessories, such as the saw blade, drill bit or cutter. This safety measure prevents unintentional starting of the electric tool.

Before starting any electric tool, remove any adjusting wrenches and screwdrivers. A tool or a wrench present in the rotating part of the machine may lead to injuries.

Prevent the machine from unintentional starting. Before plugging and/or connecting the machine to battery, handling or carrying, make sure the electric tools are switched off. Having a finger on the switch when carrying the electric tool or when the machine is on when plugging it may lead to injuries.

If you wish to work outdoors with an electric tool, only use extension cables which are approved for outdoor use and are marked accordingly. Using an extension cable suitable for outdoor use reduces the risk of electric shock.

Be careful, pay attention to what you are doing and use common sense when working with electric tools. Do not use electric tools when you are tired or under the influence of drugs, alcohol or pharmaceuticals. A moment if inattention when using electric tools may lead to serious injuries.

Check the machine for any damage Before using the equipment again, the protective equipment must carefully be checked if safe and working as designated.

Check the moving parts for perfect functioning, if working smoothly and if no parts are damaged. To provide safe operation of the equipment, all parts must be installed properly and meet all conditions.

Damaged protective equipment and parts must be professionally repaired or replaced by a recognised professional workshop, unless otherwise specified in the Operating Instructions.

Damaged switches must be replaced in a customer service workshop.

Do not use electric tools with a defective switch.

An electric tool that cannot be switched on or off is dangerous and must be repaired.

Have your electric tool repaired by an electrician.

This electric tools complies with the relevant safety regulations. Repairs may only be carried out by an electrician using genuine spare parts; otherwise the user may suffer accidents.

WARNING The use of other tools and other accessories may pose an injury risk for you.

Safety Warnings Band Saw

Wear ear protectors. Exposure to noise can cause hearing loss.

Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear and ear defenders.

Wear gloves when handling saw blades and rough materials.

The dust produced when using this tool may be harmful to health. Do not inhale the dust. Use a dust absorption system and wear a suitable dust protection mask. Remove deposited dust thoroughly, e.g. with a vacuum cleaner.

Connect the saw to a dust-collecting device when sawing wood.

Before using the tool please read the instructions. If possible have the tool demonstrated.

Before every sawing process, make sure that the machine is in a stable position. Keep the floor area free of loose material e.g. chips and cut-offs.

WARNING: Use only genuine saw bands. Do not use damaged or deformed bands.

Do not use saw blades not corresponding to the key data given in these instructions for use.

It is necessary to select a saw blade which is suitable for the material being cut.

Set the speed to suit the material you wish to cut.

Always use the protective shields on the machine.

The saw may only be used when the protective equipment is functioning properly, in good condition and in the correct position.

WARNING: Do not start the electric tool if the separating guard which protects the saw band is open.

WARNING: Do not clean the saw band while it is running.

Never reach into the danger area of the machine when it is running. Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the machine is running and the saw head is not in the rest position.

Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

Any faults with the machine, including any related to the safeguard or the saw blades, must be reported to the persons in charge of safety as soon as the faults are discovered.

In the event of a blockage, switch off the machine immediately. Pull out the mains plug and remove the jammed workpiece.

Chips and splinters must not be removed while the machine is running.

The push rod or the handle for a push rod should always be stored at the machine when not in use.

WARNING: Do not use protective equipment to transport or lift.

Mains Connection

Operation is only allowed with a safety switch against stray current (RCD max. stray current of 30mA).

Connect only to single-phase AC system voltage as indicated on the rating plate. It is also possible to connect to sockets without an earthing contact as the design conforms to safety class II. Only plug-in when machine is switched off.

Maintenance

⚠️ Unplug the machine before any work on it.

Carry out a visual inspection before switching the appliance on.

The appliance must not be used if damaged or safety equipment is defective. Replace any worn-out and damaged parts.

Caution! If the power cord of the appliance gets damaged, it must be replaced by the manufacturer or its customer service or a similarly qualified person to avoid danger.

Repairs and works specified in these Instructions may only be performed by qualified authorised staff.

Use only original accessories and original spare parts.

Be sure to disconnect the tool from the power supply before attaching or removing the saw blade.

Replace the table insert when worn

Keep the device, in particular the air vents, clean at all times. Never spray water on the device body!

Do not clean the plastics with solvents, flammable or toxic fluids. For cleaning, use a damp cloth only.

Apply environment-friendly oil to all moving parts.

Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.

If necessary, a list of spare parts can be found at www.guede.com.

Guarantee

Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.

The guarantee solely covers inadequacies caused by material defect or manufacturing defect. Original payment voucher with the sales date needs to be submitted for any claim in the guarantee period.

The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items. Failing to follow the operating and assembly instructions and common wear are also not included in the guarantee.

Important information for the customer

Please be sure to know that returning the product in or after the warranty period must be made in the original packaging.

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions?

We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label.

Tel.: [phone] / 700-360

Fax: [phone]

E-Mail: [e-mail]

WAARSCHUWING/OPGELET!

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives. In case of any change to the appliance not discussed with us the Declaration expires.

2006/95/EC 2004/108/

2009/105/EC 1907/2006/EC

2011/65/EC ROHS 2009/142/EC

□ 89/686/EEC (PPE) 1935/2004/EC

2006/42/EC

Annex IV

Notified Body 0197

Name: TUV Rheinland LGA Products GmbH

Adress: Nöstrasse 2 90431 Nürnberg Germany

Type Ex. Cert.-No.:

□97/68/EC_

Emission No.:

2000/14/EC_2005/88/EC