PT20C - Collier de dressage Dogtra - Free user manual and instructions

USER MANUAL PT20C Dogtra

ATHFINDER2 SERIES PATHFINDER2: PT20C, PR20C PATHFINDER2 MINI: PT20C, PM20C EXPLORE MORE - ADVANCED GPS TRACKING & TRAINING Owner's Manual

Please read this manual thoroughly before operating the Dogtra PATHFINDERZ series.

IMPORTANT SAFETY AND PRODUCT INFORMATION WARNING Please read all safety and product information below before using your Dogtra product. Failure to follow these safety instructions could result in injury to you, your dog and others, or it could result in damage to your Dogtra product or other property.

DOG SAFETY Proper Use

Dogtra products should be used to train, educate, monitor, or track dogs. Each dog may have a different tolerance for and reaction to Dogtra products. Closely observe your dog when determining the right level of stimulation, receiver fit, and other settings of your Dogtra product.

Training Methods Dogtra products may be used with a variety of training methods that provide clear and consistent messages to your dog.

Proper fit and wear of your Dogtra product is important for the comfort of your dog as well as the functioning of your product. Dogtra receivers should

fit comfortably and not too tightly, so that the receiver stays in place and does not move around your dog's neck. Do not leave a receiver on your dog for an extended time. Although each dog is different, Dogtra recommends that its receivers be used a maximum of 4 to 6 hours at any one time on your dog.

A receiver that is used for overly long periods or that fits improperly may cause skin irritation or sores on your dog's neck. Regularly check the receiver's contact area on your dog's skin. If your dog exhibits skinirritation or sores, stop using the Dogtra product and consult with a veterinarian.

UNAUTHORIZED USE Dogtra products should be used only in a safe and responsible manner to train, educate, monitor, or track dogs. Dogtra products are not intended for use in any other manner; they are not intended for use with other animals or with humans; and they are not intended for use in unsafe situations or environments that could lead to death, injury, loss or damage.

BATTERY Your Dogtra product contains batteries. Do not attempt to replace the battery yourself. Contact Dogtra or your Dogtra retailer to replace your battery. Dispose of batteries as provided by your local regulations. Do not disassemble, crush, heat, or otherwise alter the battery as it may cause fire, explosion, injury and/or property damage.

OWNER SAFETY Handling and Repair

Dogtra products can be damaged or malfunction if dropped, especially on hard surfaces, or otherwise improperly handled. Do not use a damaged or malfunctioning product as it may cause injury or property damage. If your product is damaged or malfunctions, contact Dogtra to obtain service before using the product.

Your Dogtra product contains electrical components and batteries. Do not use or keep your product near heat or flammable sources. Such use or storage may damage your product and/or cause fire, explosion, injury, or property damage.

Only charge your Dogtra product with its accompanying Dogtra charger. Do not attempt to charge your product in any other manner or in temperatures less than 32°F (0°C) or over 113°F (45°C) as it may cause fire, explosion, injury, and/or property damage. If you notice damage to your product, its charger, or battery, obtain service from Dogtra before charging the product. Do not use more than one splitter cable with a single battery charger.

Medical Device Interference

Dogtra products contain electrical and magnetic components that emit low level electromagnetic waves and radio frequencies. These electromagnetic waves or radio frequencies may interfere with pacemakers, defibrillators, or other medical devices. Consult your physician or medical device maker before using your medical device with a Dogtra product. If you think that your Dogtra product is interfering with your pacemaker, defibrillator, or other medical device, stop using the Dogtra product.

Do not use Dogtra products with aggressive dogs as such dogs may react adversely and cause injury to people or other dogs. Seek the assistance of a dog-training specialist or veterinarian when dealing with aggressive dogs.

Children Dogtra products are not toys. Adult supervision and close attention are necessary when Dogtra products are used by or near children.

CONTENTS PACKAGE CONTENTS + MAIN FEATURES OVERVIEW +

Owner's Manual Battery Charger Splitter Cable

2-Second GPS Update Rate

Expandable to 21Dogs

PT IPX9K Waterproof M Certified

0 Enhanced A6! Contact Points

Nick/Constant Stimulation

22% Smaller than PATHFINDER2

Low-High Output in 1-100 Stimulation Levels

Battery Charging Receptacle

GPS Antenna Mic. Sensor Antenna Casing

Contact Points Battery Charging

PATHFINDER2 MINI GPS Receiver (PM20C)

1. BUTTON FUNCTION GPS Connector (PT20C)

POWER/CONNECT PHONE BUTTON

+ On: Press the button until a green LED light appears and 3 short beeps emit.

+ Off: Press the button until a red LED light appears and 1 long beep emits.

+ Use this button to pair a smartphone. Find out more on page 62.

CONNECT GPS RECEIVER BUTTON Use this button to pair a GPS receiver. Find out more on page 63.

FUNCTION BUTTON The Function button will emit the e-collar function selected in the app when pressed. Find out more on page 70.

GPS Receiver (PR20C, PM20C)

+ On: Press the button until a green LED light appears and 3 short beeps emit.

+ Off: Press the button until a red LED light appears and 1 long beep emits.

2. LED INDICATOR GPS Connector (PT20C)

The Power LED blinks every 2 seconds while turned on. The LED colors represent the battery life:

GPS Receiver (PR20C,PM20C)

The LED on the GPS receiver blinks every 2 seconds while turned on. The LED colors represent the battery life: Green: 50-100%

The LED on the GPS Receiver will show different color when E-Fence or Locate Light function is activated.

When the E-Fence mode is on, the LED Will blink in blue in between the battery life indication blinking.

When the Locate Light is on, the white LED will blink rapidly every 0.2 seconds without the battery life indication blinking.

1. DOWNLOADING THE PATHFINDER2 APP To download the app: = 1) Go to the Apple app store or ) App Store

Google play store on your device. 2) Search for "Dogtra PATHFINDER2" app. PF2 3) Download the app on your device. PATHFINDER2

Note: Make sure to download the Dogtra PATHFINDER2 app as the previous app version is not compatible.

The appis currently compatible with:

1) Bluetooth 5.0 and above. Check the version with the phone manufacturer. 2)i0S: 12. and above, iPhone 8 and above 3) Apple Watch Series 5 and above

4) Galaxy Watch 4 and up Android 6.0 and above

Compatibilities are subject to change.

2. ONLINE WEB MANUAL PATHFINDER.

Dounloading the PATHFINDERZ App.

Use the QR code to check out the full version of the PATHFINDER2 manual and more. For more information, please check https://dogtrapathfinder.com/fr/manuals,

*PATHFINDER2 app and screenshot images are subject to change as Dogtra continues to update the software

3. PAIRING YOUR DEVICE The PATHFINDER2 GPS connector connects a smartphone and receiver. These devices need to be paired for the system to work properly.

PAIRING THE GPS CONNECTOR TO A PHONE PATHFINDER2 —

Make sure the PATHFINDER2 app has

been downloaded on your phone. Turn on Bluetooth on your phone and place the GPS connector next to your phone.

Make sure the GPS connector is off. Press and hold the Power/Connect Phone Button until a green LED light flashes and a melody plays to search for your phone.

In the app, go to the Menu tab and click on ‘Connection Failed with GPS Connector: Press the 'Connect' button once the pairing screen shows on the app.

- GPS Receiver Button

Your phone should show a connection completion screen and the green

LED will blink slowly on your GPS connector.

PAIRING THE RECEIVER TO THE GPS CONNECTOR Make sure the receiver is turned off. Press and hold the power button for more than 3 seconds until the green LED rapidly flashes and a melody plays. Release the button.

Make sure the connector is turned on. Press and hold the Connect GPS Receiver Button until the green LED rapidly flashes.

The pairing is complete when the melody stops and the LED lights stop rapidly flashing.

4. KEY FEATURES OF PATHFINDER2 APP

The blue dot will show your location on the map. Press the My Position button on the bottom right corner to recenter your location on the map.

The dog icon shows your dog's current action status. It also provides Traveled Distance, Current Speed, Altitude, Battery, Updated Time, and Shared Device.

@ Create Marker Press the icon to add a marker. You can create markers for ‘My Truck’ (car location), Truck, Dog, Tree, Favorite, or Note.

© Map Selection Select general, satellite, or terrain map.

Zoom + Zoom in once: double tap the map with one finger.

+ Zoom out once: single tap the map with two fingers.

+ Use two fingers to pinch screen to zoom in and stretch the screen to zoom out.

Scroll + You can scroll by using one finger to drag the map to the area you want to view. Tilt + Tilt the map by using two fingers and dragging the map up or down.

Rotate + Rotate the map by using two fingers and applying a turning motion.

Default Status: No motion detected.

Bark: When the dog is barking.

Pointing: When the dog is not moving and pointing towards game.

Treeing: When the dog has two paws up on the tree to force animals up the tree.

Running: When the dog is moving quickly.

Hog: When multiple dogs bark within 20 meters of the receiver.

No GPS: Receiver cannot connect to GPS and cannot send location.

No RF: Devices are far apart. Move the GPS connector to a higher area to receive signal.

Recharge Battery: Less than 20% battery life remains.

Share: Appears when another user's devices are shared. Cannot use e-collar functions on shared devices.

E-Fence On: Receiver has been synced with the E-Fence.

4-2. TOOLS TAB Recording

Get directions on Google Maps

Recording: Record sessions for location and statuses. Replay sessions from the History List on the menu.

Stopwatch: Measure the amount of time that has elapsed, which will be visible on the map.

Track: View track lines on the map for past 5 hours and reset any track information.

Timer: Set a timer that will alarm at the end of a time interval, which will be visible on the map.

Distance: Measure the distance between two points on the map.

Navigation: Use Google Maps to navigate to the marked location. Google Maps must be installed.

4-3. COMPASS TAB The Compass tab allows you to:

- View the direction and distance of dogs, selected marker, or hunter at a glance by swiping the bottom slider up.

- See each marker by swiping the slider left or right on the smallest slider size.

- Add ‘My Truck’ marker to view distance and direction.

- Use the ‘View All’ button to view all dogs and hunters at once. Dogs and hunters are not displayed when hidden or offline.

+ Metal phone cases or metal objects attached to the phone will interfere With the compass.

+ The phone may need to be calibrated for the compass to work properly.

Nick/Constant Nick will emit a single rapid pulse of stimulation. Constant will provide continuous stimulation as long as the but ton is pressed, up to 12 seconds.

Stimulation Level Set the stimulation from level 1-100 using the slider. Press and hold the button on the slider to turn the Lock feature on or off. Ca)

Pager Press Pager to emit the Pager as long as the button is pressed, up to 12 seconds.

Tone Press Tone to emit a sound as long as the button is pressed, up to 12 seconds.

Locate Light Press the Locate Light button to turn the light on or off.

Pressing the ‘Disable E-Collars’ button will disable the e-collar function on all GPS Receivers and Connector to prevent accidental stimulation until re-activated. Press the same button again to activate the e-collar function. Slide the top edge of the E-Collar tab window upward to find the Disable E-Collar button under the stimulation buttons.

1. Select the device from map or list view.

2. Select Nick or Constant and set the stimulation level from 1 to 100, which can be set for each dog.

3. You can also send commandés such as Light, Tone, or Pager.

GPS Connector's Function Button

The last used e-collar command will be color selected in the app. The Function Button on the GPS connector will operate the last selected command on the last selected collar. Keep in mind that if the Lock is on in the app, the GPS connector Function button will be locked too.

Notes: The E-Collar tab is disabled when the Tracking Only Mode is turned on in the Settings menu. Dogs are not displayed when hidden or offline.

Setting for the GPS Connector’s Function Button

Press the ‘GPS Connector Function Button Setting' icon on the E-Collar tab to arrange the stimulation type through the GPS Connector's Function button. This setting page is ideal when you want to change the stimulation type and level without commanding the GPS Receiver.

Dé: ] Function Button Setting

Function Button Settingl

Function Button Setting ©

The arranged stimulation type and/or level from this page will apply to both on the app and GPS Connector. You cannot have two different stimulation types arranged for the PATHFINDER2 app and GPS Connector.

4-5. FENCE TAB The PATHFINDER2 offers three types of fences for you to either receive a notification of your dog crossing boundaries or to auto-correct your dog.

The types of fences included are:

1. Mobile-Fence: A fence setup that moves based upon your smartphone location and will send you a notification.

2. Geo-Fence: À static fence setup that will send you a notification.

3.E-Fence: À static fence setup that will send your dog an auto-correction and send you a notification.

1) Mobile-Fence (Notification Only)

GA Mobile-Fence Setting

- Mobile-Fence is created with a radius centered around your smartphone (the blue point on the map).

- Status: Indication of receiver in or out of the fence.

- Count: Number of times the receiver has crossed the fence.

- Set the radius from 10 to 2,000 metres.

- Set the Mobile-Fence Alarm settings by going to MENU = SETTING = MOBILE-FENCE.

+ The Mobile-Fence gives a notification on the smartphone, but does not auto-correct the e-collar.

- The automatic e-collar correction will only work on the E-Fence.

2) Geo-Fence (Notification Only)

- Create Geo-Fences for specific areas to get alerts on your device.

- Status: Indication of receiver in or out of the fence.

- Count: Number of times the receiver has crossed the fence.

- Set the Geo-Fence Alarm Setting by going to MENU =} SETTING =} GEO-FENCE.

….— CS } + The Geo-Fence gives a notification on the Geo-Fence ? smartphone, but does not auto-correct the e-collar.

? + The automatic e-collar correction will only work on the E-Fence.

1. Press the @ button.

2. Move the map and place the <- on the desired area.

3. Click'Drop Point’ to create a point for the fence boundary, then repeat this step to drop the next point.

4. Press Undo to delete the last point.

5. Click the save button on the top right.

- You can create up to 15 Drop Points and up to 15 Geo-Fences.

- Edit and delete file names and fence locations in the Fence List.

(Geo-Fence Alarm Geo-Fence Alarm Setting - You can create an alarm for both exiting and entering the Geo-Fence.

- You can select different alarm types.

3)E-Fence (Auto-Correction)

Set up the static E-Fence boundary to auto-correct your dog and get notifications on your phone. When using the E-Fence, keep in mind: - This device is GPS operated and cannot be used indoors.

- Do not use this as a permanent fence solution as your dog can still cross the Outer Fence. Previous retriever training is needed to train your dog to come back over the Outer Fence.

- The receiver will not emit stimulation when bringing your dog back over the Outer Fence to the IN area.

- Make sure that Bluetooth is on to sync your receiver to the E-Fence boundary.

- Make sure that when the E-Fence boundary is updated, the receiver is synced again.

- À smartphone or GPS connection is not needed to operate, but the track information and application notification will not be received.

Correct Pager vibation for 3 sens or seœnds " © outerFence OouT

@ OUT: When moving out of the boundaries, the e-collar emits Constant correction for 5 seconds.

@ NEAR: The receiver emits a Pager vibration for 5 seconds when within 5 yards of the Outer Fence or Inner Fence.

@IN: Safe area with no correction.

@ Outer Fence: One large fence on the outskirts.

@ Near Area: Automatically created within 4,50 metres of the Inner and

Outer Fence. @ inner Fence: Up to 3 Inner Fences can be created in the Outer Fence.

For the dog's safety, the stimulation will only last 5 seconds if the dog goes out of the boundaries. Make sure your dog comes back in the boundary after 5 seconds.

Boundary design requires following:

- Minimum 850 m° area (If adding the Inner Fence, need minimum 1700 m°area).

- Minimum distance of 20 metres between each Drop Point.

The fence boundary design The fence boundary design cannot cross over. cannot have sharp pointed areas

- ON/OFF: The E-Fence can be turned on/ off by toggling the button. When turned on, the E-Fence Outer Fence shows up and a blue light on the receiver turns on.

- Status: Current receiver status of IN, NEAR, or OUT. 'Need to update’ will show up if you need to update the latest E-Fence boundary information.

- Count: The number of times the receiver Mobie-foncs +! Gao-Fance = crossed the boundary.

E-Fence - Stim Lvl: Displays the correction level when activated. Ifit is not activated, it will show OFF and you will need to @ rue go to E-Fence Settings to activate the ® stimulation setting.

When the E-Fence feature is turned on, the receiver synced with the latest E-Fence boundary will have a blue LED. If there is no blue LED, sync the receiver to the boundary by referring to "Syncing E-Fence Boundary to the Receiver" on page 78.

< E-Fonce Boundary Setup < E-Fence Boundary

E-Fence Boundary Setup

Creating the E-Fence Click on Set E-Fence Boundary.

Setting up Outer Fence

1) Press the @ button for the Outer Fence.

2) Move the map and place the - on the desired area.

3) Click ‘Drop Point’ to create a point for the fence boundary.

4) Repeat the process above to complete the boundary. Create the fence so it goes in one direction.

5) Click the save button on the top right. Only one can be saved.

Setting up Inner Fence

1) The Outer Fence must be created first to create the Inner Fence.

2) Press the @ button for the Inner-Fence.

3) Drag the area of the map you want to create the fence to the center with the +.

4) Click ‘Drop Point’ to create a point for the fence boundary.

5) Repeat the process above to complete the boundary. Create the fence so it goes in one direction.

6) Click the save button on the top right. Three can be saved.

- You can create 1 Outer-Fence and 3 Inner-Fences. All fences can use up to 15 points.

Sync E-Fence Boundary with GPS Recaivers

Syncing E-Fence Boundary to the Receiver

In order to operate the E-Fence, the receiver must

1) Turn the receiver on near the smartphone.

2) Press the Sync E-Fence Boundary button.

3) Look at the list to make sure the receiver is synced.

: Notes: : + After changing the E-Fence boundary, you ? mustsyncit agai + Each receiver must be synced individually in order for the E-Fence to operate.

Applying Stimulation on the Receiver

1) Press the Y button for the receiver on the menu. 2) Set the stimulation level.

: button to turn the E-Fence operation on or off ? for each receiver.

E-Fence Alarm Setting

- Set the E-Fence Alarm Setting by going to MENU = SETTING = E-FENCE.

- You can create an alarm for both exiting and entering the E-Fence.

- You can select different alarm types.

4-6. MENU Bluetooth Connection:

View the smartphone and GPS connector Bluetooth connection. If the devices are not paired, turn both the GPS connector and smartphone's Bluetooth off and then back on.

Notification preset: COON HUNTING Device List: Find detailed device information and set individual settings.

History List: Play recorded history files. Convert files to GFX and KML files to share.

Map Settings: Manage Offline Maps and select the size and information of the marker.

Settings: Manage settings for different map Sleep Mode features.

Describes basic contents.

1. Initial setup describes GPS connector and receiver pairing.

2. Main function will describe each tab.

Terms of Use/Privacy Policy: Check Terms of Use and Privacy Policy before use.

Manual: Quickly browse the manual.

Sleep Mode: Puts the receiver to sleep to preserve battery life. In sleep mode, the GPS signal for the receiver is turned off and will reset when turned back on.

Activity mode: select the hunting type for your activity mode to change the settings to receive device status notifications.

Select the Activity Mode for Small Game, Upland, Hog Hunting, or Custom. The status alarm settings for Running, Treeing, Pointing, Bark, and Hog will change for each mode selected. You can select the alarm you want in Custom Mode.

- Select the device's alarms based on your specific needs.

- You can set each device's alarms by going to: Menu + Device List Select Device + Alarm Setting.

- Refer to the table below for possible settings.

Category pe of Alarm Setting Up Alarm Running, Treeing, Barking, Menu + Setting + Dog Status Pointing, Hog Barking. Activity Mode Exitina f t f Menu + Setting Mobile-Fence Exting ence, entering fence, or | Mobile-Fence + otn. Mobile-Fence Alarm Menu + Setting Geo-Fence ping fence, entering fence, or Geo-Fence + Geo- ob. Fence Alarm Menu + Setting E-Fence Exiting fence, entering fence, or E-Fence + E-Fence both: Alarm E-Collar Using e-collar commands. Automatic Battery Life 20%, 15%, 10%, 5% Automatic RF connection with the receiver Automatic Device Connection and if the receiver is working. Bluetooth Connect or disconnect status. Automatic Connection

OTHER FEATURES & DETAILS PATHFINDER PF2

Downloading the 'ATHFINDER2 App.

? Use the QR code to check out the full version of the PATHFINDER2 ? manual and more. Go to https://dogtrapathfinder.com/fr/

? manuals/pathfinder-2-series to see all the app features, such as:

? - History Record, File, Detail ? - Device List Options : - Device List Sharing & Receiving - Map Management - App Settings *PATHFINDER2 app and screenshot images are subject to change as Dogtra continues to update the software

1. RECEIVER FITTING Proper Fit

Fit the receiver on either side of the dog's windpipe so that the contact points press firmly against the dog's skin. You should be able to fit two fingers underneath the collar strap.

A loose fit can allow the receiver to move around on the dog's neck and cause irritation. If the receiver is too loose, the contact will be inconsistent and cause inconsistent correction.

While Dogtra uses medical grade stainless steel contact points and anti- microbial plastic to protect the dog's skin, leaving the receiver in the same location for an extended period of time can cause skin irritation due to the sensitivity from the contact points. Reposition the receiver every few hours to move the contact points and remove the receiver after 8 hours of use. Check for skin irritation each time you use the unit.

2. FINDING THE RIGHT STIMULATION

+ Open the PATHFINDER2 app to the E-Collar tab and select your dog and stimulation level.

+ The stimulation levels are from 1 (lowest) to 100 (highest).

+ Always start at the lowest level of stimulation and work your way up.

+ The appropriate level can be found when your dog responds to the stimulation with a mild reaction, such as a tensing of the neck muscles.

Note: Every dog has a different tolerance and reaction to the stimulation. Please look at your dog's reaction to find the right level of stimulation. The stimulation level may vary depending on the situation and distractions. A distracted dog will require a higher level of stimulation compared to when there is no distraction.

3. MAXIMIZING THE DISTANCE

+ The line of sight range are following: PATHFINDER2 up to 8 km,and PATHFINDER?2 MINI up to 5 km.

+ To get the greatest range, hold the GPS connector away from your body and avoid touching the antenna.

+ Keep your unit properly charged for maximum signal strength.

+ The GPS connector device must be near your phone for proper operation, preferably less than 10 metres.

Maximum range Typical range Minimum range

Operating the PATHFINDER2 near tall buildings and other steel structures will reduce the range of the GPS signal. Not acquiring a GPS signal for prolonged periods of time while outside may indicate issues with the unit.

1. CHARGING THE PATHFINDER2 SERIES Fully charge the PATHFINDERZ series GPS Connector and Receiver before the first use. The PATHFINDERZ series uses lithium polymer batteries.

+ Only use official Dogtra chargers with the PATHFINDERZ series devices.

+ Do not charge the PATHFINDER?2 series devices near flammable substances.

+ Fully charge the PATHFINDERZ2 series devices if storing for 1 month or longer.

+ When the LED is red on the GPS connector or receiver.

+ When the app displays low battery for the GPS connector or GPS receiver. + When the LED on the transmitter or receiver will not turn on.

1. Connect the charger to the GPS connector and receiver using the splittercable.

2. Plug the charger into a 110-volt outlet.

3. When fully charged, detach the cables and plug the rubber caps over thecharging ports on the GPS connector and receiver.

4.The LED will display red while charging and green when the unit is fullycharged. À depleted battery requires 3.5 hours to fully charge.

Splitter Cable Do not use more than one splitter cable with a single battery charger.

2. REPLACING THE ANTENNA For the GPS Connector

1. Twist the antenna counter-clockwise to remove.

2. Place the new antenna on the bolt and turn clockwise to tighten the antenna.

Open the antenna enclosure by removing the 5 screws and the contact points.

Remove the screw holding the antenna in place to replace the antenna.

3. CHANGING THE CONTACT POINT LENGTH The Dogtra PATHFINDER2 comes with 15mm male contact points that can be extended to 19mm for dogs with longer coats.

To increase the length:

1) Use the included adjustment tool side marked 5/8” to unscrew the contact points counter-clockwise.

2) Place the extension over the exposed threads, flat side down.

3) Place the contact points over the extensions and tighten clockwise using the adjustment tool side marked 3/4”.

Tighten until firmly in place. Be careful not to over tighten.

To shorten the length back to 15mm, use the adjustment tool marked 3/4" to remove the extensions and then tighten the contact points clockwise using

the side marked 5/8".

4. USING THE TEST LIGHT F7

1) Turn on the receiver and place the test light over the contact points.

2) Press the Nick button in the PATHFINDER2 app and the test light will light up momentarily.

3) Press the Constant button in the PATHFINDER2 app and the test light will light up as long as the button is pressed, for up to 12 seconds.

4) The test light will glow brighter at higher levels of stimulation and dimmer with lower levels.

Note: The test light may not be visible if the intensity level is set below level ten.

5. ATTACHING THE BELT CLIP Follow the instructions below to attach the included belt clip to the GPS

connector. 1) Align the belt clip to the grooves on th

e back of the GPS connector.

2) With a firm grip, screw on the belt clip's Phillips head screws with

Caution! Tighten until firmly in place. Be careful

not to over tighten.

+ Make sure the rubber charging cap is securely in place on the GPS connector or receiver when in use.

+ Carefully inspect the unit for any missing parts or damage to the casing after use. Damaged or broken casing may affect the waterproof guarantee on the unit.

+ The antenna must be securely in place for maximum range.

+ Charge the unit for 3.5 hours before storing for extended periods.

+ Charge the unit fully once a month while in storage or before use.

+ Do not keep the unit exposed to extreme climates.

+ Dogtra may include updates and improvements to the PATHFINDER2 app which can be downloaded through the App Store and Google Play.

TROUBLESHOOTING GUIDE

1. The dog does not respond to the stimulation.

- Make sure the system is on and the strap is tight enough so that both contact points are touching your dog's skin.

- Ifthe contact points are too short, you can either purchase longer contact points or trim the hair near your dog's neck.

- Increase the level until your dog responds with a subtle head or neck movement.

2. The LED indicator light comes on, but 1 do not feel any stimulation.

- Testing the system at various levels using the test light is the best way to test your system. Your tolerance may be higher than the level you are testing on yourself.

The battery may be low. Check the LED indicator lights or the app for battery life.

. The PATHFINDERZ2 has no range or the stimulation is weaker when my dog is farther away.

Keep objects away from touching the GPS connector's antenna as the range may decrease substantially.

- The range indicated is for line-of-sight flat terrain. Heavy brush, trees, hills, buildings, and/or moisture will affect the range of your unit. For the best range, hold the GPS connector vertically above your head, and/or try moving to higher ground.

- Any electrical conductors will affect the range, such as cars, chain-link dog runs, metal structures, and radio towers. For the best results, operate away from these structures.

4. The GPS connector or receiver is not holding a charge.

- The charging pin may be damaged. À metal pin inside the charging port should stand straight up and firm in the center. If the pin is wobbly, broken or missing, you will need to send the unit in for repair.

- The charging port must be clean prior to charging, clean out any dirt with a cotton swab and some rubbing alcohol. If your dog was in salt-water, be sure to rinse the GPS receiver and charging port with clean water.

- For Dogtra units over two years old from the purchase date, the batteries may need to be replaced. You can replace them yourself by contacting Dogtra for a replacement battery. Damages incurred to the unit due to improper battery installations are not covered under the warranty. Dogtra strongly recommends sending the unit in for inspection and repair.

5. My dog has skinirritation.

- This may be due to an improper fit or from wearing the receiver too long. If your dog exhibits signs of skin irritation, consult with a veterinarian. Once your dog's skin returns to a normal condition, continue to use the receiver and check your dog's neck each time you use the unit.

FCC WARNING FOR PT20C/PR20C/PM20C This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

- Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

The PATHFINDER2 complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

QG) This device may not cause harmful interference, and

€) This device must accept any interference received, including interference that may cause undesired operation.

This is a sensitive radio device. Any unauthorized changes or modifications to this device

that are not expressly approved by Dogtra will void the warranty and may void the user's

authority to operate the equipment. Please do not tamper or modify the unit.

Radio frequency Radiation Exposure for PT20C This portable transmitter with its antenna has shown compliance with FCC's SAR limits for general population/ uncontrolled exposure. The maximum listed SAR level is 2.55 W/kg (Limb), The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter.

Radio frequency Radiation Exposure for PR20C/PM20C To comply with FCC RF exposure compliance requirements, a separation distance of at least Tcm must be maintained between the antenna of this device and all persons. This device must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications (including the antenna) made to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment.

IC RESTRICTIONS This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is Subject to the following two conditions:

() this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired Operation of the device.

IC RF Radiation Exposure Statement: (PR20C/PM20C)

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 17cm between the radiator and your body.

IC SAR warning: (PT20C)

The highest SAR value reported under this standard during product certification for use in the hand is 2.55 W/kg.

WARRANTY AND REPAIR INFORMATION LIMITED WARRANTY For Dogtra Products Purchased from Dogtra Authorized Dealers

Two-Year Limited Warranty

Dogtra-Canada provides the original purchaser with a 2-YEAR LIMITED WARRANTY for the products sold by Dogtra-Canada and its authorized distributors/retailers. The warranty begins from the date of the original purchase. The replaceable batteries of YS100, iQ No Bark Collar, iQ CLiQ and BALL TRAINER are not covered by Warranty.

* The cost of shipping products under warranty back to Dogtra-Canada is the customer’s responsibility. Dogtra-Canada will provide/pay (via regular ground service) the shipping cost back to the customer. Any expedited shipping service will be at the customer's expense.

If a repair is not covered by warranty, the cost of Parts, Accessories, Labor fees, and Shipping fees incurred are the customer's responsibility. Labor fees will be variable depending on the extent of the work required.

To Qualify for the Dogtra Warranty A proof of purchase is required to initiate repair work under warranty. We strongly recommend keeping the original receipt.

Not Covered Under Warranty

Dogtra-Canada DOES NOT cover the cost of repairs and replacements due

to misuse by the owner or dog, improper maintenance, and/or lost units. Any water damage on the Water Resistant Transmitters of the Dogtra 175NCP, 180NCP, 200NCP, 400NCP, 410NCP, iQ PLUS, iQ CLiQ and BALL TRAINER and the Water Resistant Receivers of the RRS, RRD, RR Deluxe and BALL TRAINER, will not be covered. All replacement costs for either the transmitter or receiver will be the owner's responsibility. The warranty does not cover failure resulting from damage, abuse or loss of parts. The warranty is void if the unit has been altered or an unauthorized person has damaged the unit while attempting repair work. Battery replacement by the customer during the warranty period is not recommended. If the customer chooses to replace the batteries, any damage to the unit during the change-out by the owner will void the warranty. The removal of serial numbers from any Dogtra products will void the warranty. Dogtra reserves the right to retain and discard any parts or accessories that have been found damaged upon replacement and repair.

Out of Warranty Repair Work

For repair work that is no longer covered by warranty, the cost of repair will include parts, labor and shipping. The owner will be informed about the repair costs before the product is repaired. Write a note briefly explaining the problem. Include your name, address, city/zip code, phone number and email address.

Procedure for Repair Work

If the unit is malfunctioning, please refer to the “Troubleshooting Guide” in

the Owner's Manual and contact customer service by phone at 1-778-956-7922 or by email at Info.canada@dogtra.com, for technical support, before sending it to Dogtra-Canada for Service.

The cost of shipping products under warranty back to Dogtra-Canada is the customer's responsibility. Dogtra-Canada is not responsible for units damaged or lost in transition to Dogtra. Dogtra-Canada is not responsible for loss of training time or inconvenience while the unit is in for repair work. Dogtra-Canada does not provide loaner units or any form of compensation during the repair period. A copy of the sales receipt showing the purchase date is required before warranty work is initiated.

Please include a brief explanation outlining the problem and include your name, address, city/state/zip code, daytime phone number, evening phone number, and email address. If the repair costs are not covered under warranty, we

will call you for payment information and authorization. For any questions concerning your Dogtra products, call us at 1-778-956-7922, or email us at Info.canada@dogtra.com.

Dogtra-Canada 8661 201st Street, 2nd Floor Langley, BC, V2Y 0G9

The diagrams and representations in the manual may differ slightiy from the actual product depending on the model type.

Accus rechargeables en3,5h

ï ls— Menu principal ñ

8661 201st Street, 2nd Floor Langley, BC, V2Y 0G9