Ovation F-55FC - Light projector Chauvet Professional - Free user manual and instructions

Product Type	Full-color RGBAL Fresnel-style light projector
Brand	Chauvet Professional
Model	Ovation F-55FC
Dimensions (L x W x H)	9.64 x 4.64 x 6.53 in (245 x 118 x 166 mm)
Weight	5.4 lb (2.4 kg)
Power Supply	Auto-ranging 100-240 VAC, 50/60 Hz
Power Consumption	28 W (120 V) / 27 W (230 V)
Fuse	T 1 A, 250 V
Light Source	3 RGBAL LEDs, 3-4 W each, 700 mA, 50,000 hours
Zoom Range	Manual 18° to 87° field angle
DMX Channels	1, 3, 5, 7, 10, 12, 13, 16 or HSV
DMX Connector	5-pin XLR
Control Modes	DMX, Master/Slave, Standalone
Virtual Color Wheel	Premixed colors and color temperature presets
Cooling System	Convection, max ambient 113°F (45°C)
IP Rating	IP20, indoor use only
Included Accessories	Quick Reference Guide, gel frame
Maintenance	Clean at least twice monthly; use soft brush and isopropyl alcohol
Repair	No user-serviceable parts; service by certified technicians
Safety Notes	Grounded circuit required; disconnect before cleaning/fuse replacement

Frequently Asked Questions - Ovation F-55FC Chauvet Professional

What DMX personalities are available on the Ovation F-55FC?

The Ovation F-55FC supports 1Ch, 3Ch, 5Ch, 7Ch, 10Ch, 12Ch, 13Ch, 16Ch, and HSV DMX personalities, allowing flexible control of dimmer, RGBAL, virtual color wheel, color temperature, and strobe functions.

How do I replace the fuse?

First, disconnect the product from power. Use a flathead screwdriver to unscrew the fuse holder cap, remove the blown fuse, and replace it with a T 1 A, 250 V fuse. Screw the cap back and reconnect power.

How can I set up Master/Slave operation?

Connect the products in a daisy chain. Set each slave to Slave mode in the Master/Slave menu. Set the master to Master mode and run a program (Auto or Static). Do not connect a DMX controller, as it may interfere.

What is the Virtual Color Wheel?

The Virtual Color Wheel provides over 30 premixed colors (e.g., C3050 Md Yellow, C1080 Md Red) and color temperature presets (2800K to 6500K). It is available as a standalone mode and as a DMX channel, simplifying color matching to gel colors.

How should I clean the Ovation F-55FC?

Clean at least twice a month. Unplug the fixture, allow it to cool, then use a vacuum or soft brush to remove dust from vents. Clean transparent surfaces with a mild soap solution or isopropyl alcohol applied to a lint-free cloth.

What are the mounting and safety requirements?

Mount only indoors (IP20) with adequate ventilation (20 cm from surfaces). Always secure with a safety cable and use a mounting clamp with sufficient weight capacity. The maximum ambient temperature is 113°F (45°C).

How do I reset the product to factory defaults?

Navigate to Reset Factory in the menu, select Yes, and press Enter. This restores all settings to their original values, including DMX address and white balance.

What is the expected LED lifespan?

The RGBAL LEDs have an average lifespan of 40,000 to 50,000 hours. To extend longevity, ensure proper ventilation and avoid running the LEDs at full intensity for extended periods.

Why is the fixture not responding to DMX?

Check the DMX address (001-512) to avoid overlap. Verify that the correct DMX personality is selected and that the 5-pin XLR cables are connected properly. Also, confirm the DMX controller is sending signals.

Is the Ovation F-55FC suitable for outdoor use?

No, the fixture has an IP20 rating, meaning it is only protected against objects larger than 12 mm. It must be used indoors and protected from dust, excessive heat, water, and humidity.

USER MANUAL Ovation F-55FC Chauvet Professional

OVATION

F-55FC

User Manual

Model ID: OVATIONF55FC

Edition Notes

The Ovation F-55FC User Manual includes a description, safety precautions, installation, programming, operation and maintenance instructions for the Ovation F-55FC.

Trademarks

CHAUVET, the Chauvet logo and Ovation F-55FC are registered trademarks or trademarks of Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.

Copyright Notice

The works of authorship contained in this manual, including, but not limited to, all design, text and images are owned by Chauvet.

© Copyright 2022 Chauvet & Sons, LLC. All rights reserved.

Electronically published by Chauvet in the United States of America.

Manual Use

Chauvet authorizes its customers to download and print this manual for professional information purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this manual or its content for any other purpose without written consent from Chauvet.

Document Printing

For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4 paper (210 x 297 mm), configure the printer to scale the content accordingly.

Intended Audience

Any person installing, operating, and/or maintaining this product should completely read through the guide that shipped with the product, as well as this manual, before installing, operating, or maintaining this product.

Disclaimer

Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest version from www.chauvetprofessional.com.

Document Revision

This Ovation F-55FC User Manual is the 7 ^th edition of this document. Go to www.chauvetprofessional.com for the latest version.

TABLE OF CONTENTS

1. Before You Begin .... 1

What Is Included 1

Claims 1

Manual Conventions 1

Symbols 1

Safety Notes 2

Personal Safety 2

Mounting and Rigging 2

Power and Wiring.... 2

Operation 2

Expected LED Lifespan.... 2

2. Introduction ...... 3

Description 3

Features 3

Product Overview.... 3

Product Dimensions 4

3. Setup 5

AC Power 5

AC Plug 5

Fuse Replacement 5

DMX Linking.... 5

DMX Personalities.... 5

Remote Device Management (RDM) 5

Master/Slave Connectivity.... 6

Mounting 6

Orientation.... 6

Rigging 6

Procedure....6

4. Operation 7

Control Panel Operation.... 7

Control Options 7

Programming.... 7

Configuration (DMX) 7

DMX Personalities.... 7

Starting Address.... 7

Menu Map 8

Configuration (Standalone) 10

Static Mode 10

Color X-Fade Speed 10

Auto Programs 11

Red Shift 11

Master/Slave 11

Dimmer Curve.... 11

Dimmer Profiles.... 11

White Balance 11

LED Frequency 11

Back Light 12

System Information 12

Factory Reset 12

Virtual Color Wheel (VCW) 12

DMX Values 13

16Ch / 13Ch / 12Ch / 10Ch / 7Ch / 5Ch / 3Ch.... 13

HSV 14

1Ch.... 14

1. Technical Information.... 15

Product Maintenance 15

1. Technical Specifications .... 16

Returns.... 17

Contact Us 18

1. Before You Begin

What Is Included

- Ovation F-55FC

• Quick Reference Guide

- Gel frame

Claims

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate customer's claim. In addition, keep the box and contents for inspection.

For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Manual Conventions

Convention	Meaning
1-512	A range of values
50/60	A set of values of which only one can be chosen
	A button on the product's control panel
Settings	A product function or a menu option

Symbols

Symbol		Meaning
		Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
		Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
		Important installation or configuration information. The product may not function correctly if this information is not used.
		Useful information.

The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data transmission protocol.

FCC Compliance

This device complies with Part 15 Part B of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Safety Notes

Read all the following safety notes before working with this product. These notes contain important information about the installation, usage, and maintenance of this product.

This product contains no user-serviceable parts. Any reference to servicing in this User Manual will only apply to properly trained, certified technicians. Do not open the housing or attempt any repairs.

All applicable local codes and regulations apply to proper installation of this product.

Personal Safety

• Avoid direct eye exposure to the light source while the product is on.
  • Always disconnect the product from the power source before cleaning or replacing the fuse.
  • Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product's housing when operating because it may be very hot.

Mounting and Rigging

• Do not operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it (IP20).
• Do not leave any flammable material within 50 cm of this product while operating or connected to power.
• CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to warm, humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• When hanging this product, always secure to a fastening device using a safety cable.
  • Use only the hanging/mounting bracket to carry this product.

Power and Wiring

• Always ensure that the product is connected to proper voltage in accordance with the specifications in this manual or on the product's specification label.
  • Never connect the product to a dimmer pack or rheostat.
• Never disconnect this product by pulling or tugging on the power cable.

Operation

• Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
  • The minimum startup temperature is -4°F ( -20°C ). Do not start the product at lower temperatures.
• The minimum ambient temperature is -22°F (-30°C). Do not operate the product at lower temperatures.
  • In the event of a serious operation problem, stop using this product immediately!

If your Chauvet product requires service, contact Chauvet Technical Support.

Expected LED Lifespan

Over time, use and heat will gradually reduce LED brightness. Clustered LEDs produce more heat than single LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity.

2. Introduction

Description

The Ovation F-55FC is a full-color RGBAL inkie Fresnel-style fixture. The virtual color wheel and color temperature presets are shared from Chauvet's other full-color Ovation fixtures. A manual zoom with a 32° to 87° field angle allows the product to have a soft field of light when needed.

Features

- Operating modes:

• 1-channel: dimmer
• 3-channel: dimmer, virtual color wheel, color temperature
• 5-channel: RGBAL
  • 7-channel: dimmer, RGBAL, strobe
  • 10-channel: 16-bit dimmer, RGBAL, virtual color wheel, color temperature, strobe
• 12-channel: dimmer, RGBAL, virtual color wheel, color temperature, strobe, auto program, auto speed, control
  • 13-channel: dimmer, 16-bit RGBAL, 16-bit dimmer, strobe

• 16-channel: 16-bit dimmer, 16-bit RGBAL, virtual color wheel, color temperature, strobe, control
  • HSV: hue, saturation, value

• Compact, full-color Fresnel for tight spaces and on-location lighting

• Soft and even field of light
  • 16-bit dimming resolution for smooth fades
  • Virtually silent operation for use in any situation
  • Manually controlled variable zoom range between 18° and 87°

Product Overview

Product Dimensions

3. Setup

AC Power

Each Ovation F-55FC has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each Ovation F-55FC, refer to the label affixed to the product or to the Technical Specifications chart in this manual.

The listed current rating indicates the maximum current draw during normal operation. For more information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.

• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

AC Plug

Connection	Wire (U.S.)	Wire (Europe)	Screw Color
AC Live	Black	Brown	Yellow or Brass
AC Neutral	White	Blue	Silver
AC Ground	Green/Yellow	Green/Yellow	Green

Fuse Replacement

1. Disconnect this product from the power outlet.
2. Using a flathead screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating (T 1 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.

Make sure to disconnect the product's power cord before replacing a blown fuse. Always replace the blown fuse with another of the same type and rating.

DMX Linking

The Ovation F-55FC can be linked to a DMX controller using a 5-pin DMX connection. If using other DMX-compatible products with this product, it is possible to control each individually with a single DMX controller.

DMX Personalities

The Ovation F-55FC uses a 5-pin DMX data connection for the 1Ch, 3Ch, 5Ch, 7Ch, 10Ch, 12Ch, 13Ch, 16Ch, and HSV DMX personalities.

• Refer to the Introduction for a brief description of each DMX personality.
- Refer to the Operation chapter to learn how to configure the Ovation F-55FC to work in these personalities.
• The DMX Values section provides detailed information regarding the DMX personalities.

For information about DMX standards, Master/Slave connectivity, or the DMX cables needed to link this product to a DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.

Remote Device Management (RDM)

Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally along existing DMX cabling. Check the DMX controller's User Manual or with the manufacturer, as not all DMX controllers have this capability. The Ovation F-55FC supports RDM protocol that allows feedback to make changes to menu map options.

Master/Slave Connectivity

The Master/Slave mode allows an Ovation F-55FC (the master) to control one or more Ovation F-55FC products (the slaves) without a DMX controller. One Ovation F-55FC becomes the master when running an auto or custom program, or by being in a Static mode.

Each slave's control panel must be configured to operate in Slave mode. During Master/Slave operation, the slaves will operate in unison with the master.

DO NOT connect a DMX controller to products operating in Master/Slave mode. The DMX controller signals may interfere with the signals from the master.

• The Operation section of this manual provides detailed instructions on how to configure the master and slaves.
• For more information about DMX standards or the DMX cables needed to link this product to a DMX controller, download the DMX primer from the Chauvet website: www.chauvetprofessional.com.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. For CHAUVET Professional line of mounting clamps, go to: http://trusst.com/products/.

Orientation

Always mount this product in a safe position, ensuring that there is adequate room for ventilation, configuration, and maintenance.

Rigging

Chauvet recommends using the following general guidelines when mounting this product:

• Before deciding on a location for the product, make sure there is easy access to the product for maintenance and programming purposes.
• Make sure that the structure onto which the product will be mounted can support the product's weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power-linking cables to reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.

Procedure

The Ovation F-55FC comes with a double-bracketed yoke that can be used as a floor stand or to which mounting clamps can be attached for hanging. Mounting clamps must be purchased separately. Ensure that the clamps can support the weight of this product. Use at least one mounting point per product where necessary.

Mounting Diagram

4. Operation

Control Panel Operation

Button	Function
	Exits from the current menu or function
	Enables the currently displayed menu or sets the currently selected value in to the current function
	Navigates upward through the menu list or increases the numeric value when in a function
	Navigates downward through the menu list or decreases the numeric value when in a function

Control Options

Set the Ovation F-55FC starting address in the 001-512 DMX range.

Programming

Refer to the Menu Map to understand the menu options. The menu map shows the main level and a variable number of programming levels for each option.

• To go to the desired main level, press repeatedly until the option shows on the display. Press to select. This will show the first programming level for that option.
• To select an option or value within the current programming level, press or until the option shows on the display. Press to select. This will show either the first option if there is another programming level, or the selected value.
• Press repeatedly to exit to the previous main level.

Configuration (DMX)

Use DMX configurations to operate the product with a DMX controller.

DMX Personalities

This setting allows the user to choose a particular DMX personality.

1. Go to the DMX Channel main level.
2. Select the desired personality (1Ch, 3Ch, 5Ch, 7Ch, 10Ch, 12Ch, 13Ch, 16Ch, and HSV).

• See the Starting Address section for the highest starting address suggested for each personality.
• Make sure that the starting addresses on the various products do not overlap due to the new personality setting.

Starting Address

In this mode, each product will respond to a unique starting address from the DMX controller. All products with the same starting address will respond in unison.

1. Go to the DMX Address main level.
2. Set the starting address (001–512).

The highest recommended starting address for each DMX mode is as follows:

DMX Personality	DMX Address	DMX Personality	DMX Address
1Ch	512	12Ch	501
3Ch	510	13Ch	500
5Ch	508	16Ch	497
7Ch	506	HSV	510
10Ch	503

Menu Map
Refer to the Ovation F-55FC product page on www.chauvetprofessional.com for the latest menu map.

Main Level	Programming Levels			Description
DMX Address	Address		001-512*	Selects starting address (*highest channel restricted to personality chosen)
DMX Channel	1Ch		Virtual Color Wheel	1-channel: dimmer
			Color Temperature
			Manual Color Mixer
	3Ch			3-channel: dimmer, virtual color wheel, color temperature
	5Ch			5-channel: RGBAL
	7Ch			7-channel: RGBAL, dimmer, strobe
	10Ch			10-channel: 16-bit dimmer, RGBAL, virtual color wheel, color temperature, strobe
	12Ch			12-channel: RGBAL, dimmer, virtual color wheel, color temperature, strobe, auto program, auto speed, control
	13Ch			13-channel: 16-bit RGBAL and dimmer, strobe
	16Ch			16-channel: 16-bit RGBAL and dimmer, virtual color wheel, color temperature, strobe, control
	HSV			3-channel: hue, saturation, value
Virtual Color Wheel	Virtual Color Wheel	C3050 - Md Yellow	Dimmer 0-255	Virtual Color Wheel simulates the output of each gel color. Refer to the Virtual Color Wheel Chart section for specific values.
		C3040 - Lt Yellow
		C3240 - Amb Yellow
		C2340 - VLt Amber
		C2040 - Lt Amber
		C2050 - Md Amber
		C2060 - Dk Amber
		C1050 - Lt Red
		C1080 - Md Red
		C1020 - NC Pink
		C1030 - Md Pink
		C1630 - Dk Pink
		C1250 - Md Red Amber
		C1060 - Dk Red Amber
		C1650 - Magenta
		C6170 - Dk Magenta
		C6020 - Lt Lavender
		C5030 - Lt Blue
		C5020 - VLt Blue
		C5430 - Lt Blue 2
		C5070 - Blue
		C5050 - Md Blue
		C5060 - Dk Blue
		C5690 - Indigo
		C5080 - VDk Blue
		C5081 - VDk Blue 2
Virtual Color Wheel (cont.)	Virtual Color Wheel (cont.)	C4370 - Yel Green	Dimmer 0-255	Virtual Color Wheel simulates the output of each gel color. Refer to the Virtual Color Wheel Chart section for specific values.
		C4070 - Green
		C4550 - Turquoise
		C4560 - Aqua
		C4570 - Blue Green
	Color Temperature	2800K	Dimmer 0-255	Preset white color temperatures. Emulates a tungsten lamp at the specified color temperature. Refer to the Color Temperature Chart section for specific values.
		3000K
		3200K
		3500K
		4000K
		4500K
		5000K
		5600K
		6000K
		6500K
	Manual Color Mixer	Red	0-255	Combine red, green, blue, amber, and lime to make a custom color (0-100%)
		Green
		Blue
		Amber
		Lime
	Color X-Fade Speed	Off		Turns off the fade transition between colors
		X-Fade Speed 1		Creates fade transition between colors when using colors in the Virtual Color Wheel or Color Temperature chart, from fast (X-Fade Speed 1) to slow (X-Fade Speed 4)
		X-Fade Speed 2
		X-Fade Speed 3
		X-Fade Speed 4
Auto Show	Auto 1-5		1-100	Selects automatic programs and auto speed
Red Shift	On			Mimics halogen lamp dimming
	Off
Master/ Slave	Master			Master mode
	Slave			Slave mode
Dimmer Curve	SCurve			Sets the dimmer curve
	Linear
	Square
	Inverse Square
Dimmer Mode	Off			Linear dimmer
	Dimmer 1-3			Dimming curves, from fast (Dimmer 1) to slow (Dimmer 3)
White Balance	Off			Uses factory default white setting
	Manual	Red	125-255	Sets red LED maximum value
		Green		Sets green LED maximum value
		Blue		Sets blue LED maximum value
		Amber		Sets amber LED maximum value
		Lime		Sets lime LED maximum value

Main Level	Programming Levels		Description
LED Frequency	600Hz		Selects the PWM output frequency
	1200Hz
	2000Hz
	4000Hz
	6000Hz
	25KHz
Back Light	10S		Turns off display backlight after 10 seconds of inactivity
	30S		Turns off display backlight after 30 seconds of inactivity
	2Min		Turns off display backlight after 2 minutes of inactivity
	Always On		Display backlight always on
Information	Fixture Hours	____H	Shows total product hours
	LED Hours	____H	Shows total LED hours
	Version	V__	Shows installed software version
	UID	____	Shows product UID
Reset Factory	No		Reset to factory defaults
	Yes

Configuration (Standalone)

Use standalone configuration to operate the product without a DMX controller.

Static Mode

The Static mode allows for an unchanging color without a DMX controller.

Virtual Color Wheel

1. Go to the Virtual Color Wheel main level.
2. Select Virtual Color Wheel.
3. Select the desired gel color (see Virtual Color Wheel Chart).
4. Select the desired output level (0–255).

Color Temperature

To select a color temperature, do the following:

1. Go to the Virtual Color Wheel main level.
2. Select Color Temperature.
3. Select the desired color temperature (see Color Temperature Chart).
4. Select the desired output level (0–255).

Manual Color Mixer

To do color mixing without a DMX controller, follow the instructions below:

1. Go to the Virtual Color Wheel main level.
2. Select Manual Color Mixer.
3. Select the color to edit (Red, Green, Blue, Amber, or Lime).
4. Select the desired output level for that color (0–255).
5. Repeat steps 3 and 4 until product outputs as desired.

Color X-Fade Speed

The Color X-Fade Speed sets the cross-fade speed for Virtual Color Wheel options.

1. Go to the Virtual Color Wheel main level.
2. Select Color X-Fade Speed.
3. Select the desired cross-fade speed (Off, X-Fade Speed 1–4).

Auto Programs

Auto programs allow for dynamic blinder effects without a DMX controller.

1. Go to Auto Show main level.
2. Select the desired auto program (Auto 1-5).
3. Select the desired speed (1–100).

Red Shift

The Red Shift function imitates the dimming of a halogen lamp. To toggle Red Shift:

1. Go to the Red Shift main level.
2. Select On or Off.

Master/Slave

The Master/Slave mode allows a group of Ovation F-55FC products (the slaves) to simultaneously duplicate the output of another Ovation F-55FC (the master) without a DMX controller.

To set each of the slaves:

1. Go to the Master/Slave main level
2. Select Slave.

To set the master:

1. Go to the Master/Slave main level
2. Select Master.
3. Select a static setting.

• The master is the one that runs a program whether in Auto or Static mode.
- Do not connect a DMX controller to the products configured for Master/Slave operation. The DMX controller may interfere with signals from the master.
• The master should be the first product in the daisy chain.

Dimmer Curve

To set the dimmer curve, follow the instructions below:

1. Go to the Dimmer Curve main level.
2. Select the desired option (SCurve, Linear, Square, or Inverse Square).

Dimmer Profiles

This setting determines how fast the output of the Ovation F-55FC changes when the output value is modified. It provides four different options to simulate the dimming curve of an incandescent lighting product. To select a specific dimmer profile, do the following:

1. Go to the Dimmer Mode main level.
2. Select a dimmer curve (Off, Dimmer 1, Dimmer 2, or Dimmer 3).

Off: The output is proportional (linear) to the dimmer channel value. Dimmer 1-3: The output follows the dimmer value based on the corresponding dimmer curve, Dimmer 1 being the fastest.

White Balance

This setting determines the maximum output values for each color, which affects the appearance of a full output white.

1. Go to the White Balance main level.
2. Select Off (the product will use a default setting) or Manual.
3. For Manual mode, select the color value to edit (Red, Green, Blue, Amber, or Lime Green).
4. Set the maximum value for the selected color (125–255).
5. Repeat steps 3 and 4 until the product outputs as desired.

LED Frequency

This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the Ovation F-55FC. To do so, follow the instructions below:

1. Go to the LED Frequency main level.
2. Select PWM Frequency (600Hz, 1200Hz, 2000Hz, 4000Hz, 6000Hz, or 25Khz).

Back Light

This setting allows for selection of the amount of time the backlight on the Ovation F-55FC's display stays on after the last button is pressed on the control panel.

1. Go to the Back Light main level.
2. Select 10S (10 seconds), 30S (30 seconds), 2Min (2 minutes), or Always On (remains on).

System Information

This option displays essential product information.

1. Go to the Information main level.
2. Select Fixture Hours, LED Hours, Version, or UID.

Factory Reset

This option restores the Ovation F-55FC to factory default settings.

1. Go to the Reset Factory main level.
2. Select No or Yes.

Virtual Color Wheel (VCW)

The Ovation F-55FC includes a feature called the Virtual Color Wheel (VCW). This feature is available as a standalone control mode for manual use and as a control channel in select DMX personalities. More than 30 premixed colors, blended by Chauvet engineers, are available to call up for easier programming.

The DMX values used to mix these colors are provided below. The overall intensity of the Ovation fixture can be adjusted to more closely replicate familiar industry-standard colors. A chart is available at www.chauvetprofessional.com to compare Chauvet's premixed colors with popular gel colors. This chart is for comparison purposes only and is not an assertion that Chauvet's colors match any listed gel color.

Virtual Color Wheel Chart

DMX Value	Display Readout	Red Value	Green	Blue	Amber	Lime
000 ⇔ 005	--	000	000	000	000	000
006 ⇔ 013	C3050 - Md Yellow	233	163	020	123	255
014 ⇔ 021	C3040 - Lt Yellow	224	158	047	255	231
022 ⇔ 028	C3240 - Amb Yellow	180	060	000	245	255
029 ⇔ 035	C2340 - VLt Amber	245	107	081	255	213
036 ⇔ 043	C2040 - Lt Amber	230	130	062	255	155
044 ⇔ 051	C2050 - Md Amber	255	000	025	255	194
052 ⇔ 059	C2060 - Dk Amber	255	000	024	255	150
060 ⇔ 067	C1050 - Lt Red	255	037	027	030	038
068 ⇔ 075	C1080 - Md Red	255	004	017	000	000
076 ⇔ 083	C1020 - NC Pink	238	135	129	255	255
084 ⇔ 091	C1030 - Md Pink	255	131	120	255	195
092 ⇔ 099	C1630 - Dk Pink	255	165	123	255	210
100 ⇔ 107	C1250 - Md Red Amber	255	000	041	195	055
108 ⇔ 115	C1060 - Dk Red Amber	255	000	045	120	030
116 ⇔ 121	C1650 - Magenta	255	050	115	255	115
122 ⇔ 130	C6170 - Dk Magenta	255	035	117	000	000
131 ⇔ 138	C6020 - Lt Lavender	127	122	142	251	255
139 ⇔ 146	C5030 - Lt Blue	000	255	197	100	255
147 ⇔ 154	C5020 - VLt Blue	158	255	189	000	255
155 ⇔ 162	C5430 - Lt Blue 2	000	255	180	000	243
163 ⇔ 170	C5070 - Blue	043	255	210	043	036
171 ⇔ 178	C5050 - Md Blue	000	255	218	000	181
179 ⇔ 186	C5060 - Dk Blue	000	210	206	000	118
187 ⇔ 194	C5690 - Indigo	065	000	210	040	055
195 ⇔ 202	C5080 - VDk Blue	000	203	230	000	040
203 ⇔ 210	C5081 - VDk Blue2	040	199	240	000	045
211 ⇔ 218	C4370 - Yel Green	027	255	028	016	104
219 ⇔ 226	C4070 - Green	049	255	055	120	090
227 ⇔ 234	C4550 - Turquoise	060	230	109	000	245
235 ⇔ 242	C4560 - Aqua	020	240	126	036	255
243 ⇔ 250	C4570 - Blue Green	000	255	079	030	053
251 ⇔ 255	--	000	000	000	000	000

The colors above are simulated renditions of the color output produced compared with other similar incandescent products. Chauvet makes no guarantee of the color output accuracy.

Color Temperature Chart

DMX Value	Display Readout	Red Value	Green	Blue	Amber	Lime
000 ⇔ 005	--	000	000	000	000	000
006 ⇔ 025	2800K	195	177	154	255	255
026 ⇔ 050	3000K	191	186	161	255	255
051 ⇔ 075	3200K	186	195	169	255	255
076 ⇔ 100	3500K	181	205	179	255	255
101 ⇔ 125	4000K	175	221	192	255	255
126 ⇔ 150	4500K	169	231	204	255	255
151 ⇔ 175	5000K	163	239	213	255	255
176 ⇔ 200	5600K	157	247	223	255	255
201 ⇔ 225	6000K	154	251	230	255	255
226 ⇔ 250	6500K	153	255	238	255	255
251 ⇔ 255	--	000	000	000	000	000

The color temperatures above are simulated renditions of the color output produced compared with a tungsten lamp at the specified color temperature. Chauvet makes no guarantee of the color output accuracy.

DMX Values

16Ch / 13Ch / 12Ch / 10Ch / 7Ch / 5Ch / 3Ch

3Ch	5Ch	7Ch	10Ch	12Ch	13Ch	16Ch	Function	Value	Percent/Setting
1	-	1	1	1	1	1	Dimmer	000 ⇔ 255	0–100%
-	-	-	2	-	2	2	Dimmer fine	000 ⇔ 255	0–100%
-	1	2	3	2	3	3	Red	000 ⇔ 255	0–100%
-	-	-	-	-	4	4	Red fine	000 ⇔ 255	0–100%
-	2	3	4	3	5	5	Green	000 ⇔ 255	0–100%
-	-	-	-	-	6	6	Green fine	000 ⇔ 255	0–100%
-	3	4	5	4	7	7	Blue	000 ⇔ 255	0–100%
-	-	-	-	-	8	8	Blue fine	000 ⇔ 255	0–100%
-	4	5	6	5	9	9	Amber	000 ⇔ 255	0–100%
-	-	-	-	-	10	10	Amber fine	000 ⇔ 255	0–100%
-	5	6	7	6	11	11	Lime	000 ⇔ 255	0–100%
-	-	-	-	-	12	12	Lime	000 ⇔ 255	0–100%
-	-	7	8	7	13	13	Strobe	000 ⇔ 010	No function
								011 ⇔ 255	Strobe, slow to fast
2	-	-	9	8	-	14	Virtual color wheel	000 ⇔ 255	Refer to the Virtual Color Wheel Chart
3	-	-	10	9	-	15	Color temperature	000 ⇔ 255	Refer to the Color Temperature Chart
-	-	-	-	10	-	-	Auto programs	000 ⇔ 010	No function
								011 ⇔ 060	Auto program 1
								061 ⇔ 110	Auto program 2
								111 ⇔ 160	Auto program 3
								161 ⇔ 210	Auto program 4
								211 ⇔ 255	Auto program 5
-	-	-	-	11	-	-	Auto speed	000 ⇔ 255	0–100%
-	-	-	-	12	-	16	Control(hold for 3 seconds)	000 ⇔ 007	No function
								008 ⇔ 015	Dimmer reset
								016 ⇔ 023	Red shift on
								024 ⇔ 031	Red shift off
								032 ⇔ 039	S-curve dimmer
								040 ⇔ 047	Linear dimmer
								048 ⇔ 055	Square dimmer curve
								056 ⇔ 063	Inverse square dimmer curve
								064 ⇔ 071	Dimmer speed mode OFF
								072 ⇔ 079	Dimmer speed 1 (fastest)
								080 ⇔ 087	Dimmer speed 2
								088 ⇔ 095	Dimmer speed 3 (slowest)
								096 ⇔ 103	X-Fade Speed: OFF
								104 ⇔ 111	X-Fade Speed: 1 (fastest)
								112 ⇔ 119	X-Fade Speed: 2
								120 ⇔ 127	X-Fade Speed: 3
								128 ⇔ 135	X-Fade Speed: 4 (slowest)
								136 ⇔ 255	Reserved for future use

HSV

Channel	Function	Value	Percent/Setting
1	Dimmer	000 ⇔ 255	0–100%
2	Saturation	000 ⇔ 255	0–100%
3	Value	000 ⇔ 255	0–100%

1Ch

Channel	Function	Value	Percent/Setting
1	Dimmer	000 ⇔ 255	0–100% (color set through display menu)

5. Technical Information

Product Maintenance

To maintain optimum performance and minimize wear, clean this product frequently. Usage and environment are contributing factors in determining the cleaning frequency.

Clean this product at least twice a month. Dust build-up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear.

To clean the product:

1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.

Always dry the transparent surfaces carefully after cleaning them.

6. Technical Specifications

Dimensions and Weight

Length	Width	Height	Weight
9.64 in (245 mm)	4.64 in (118 mm)	6.53 in (166 mm)	5.4 lb (2.4 kg)

Note: Dimensions in inches rounded to the nearest hundredth.

Power

Power Supply Type		Range		Voltage Selection
Switching (internal)		100 to 240 VAC, 50/60 Hz		Auto-ranging
Parameter	100 V, 60 Hz	120 V, 60 Hz	208 V, 60 Hz	230 V, 50 Hz	240 V, 50 Hz
Consumption	28 W	28 W	27 W	27 W	27 W
Operating Current	0.467 A	0.392 A	0.243 A	0.224 A	0.211 A
Fuse	T 1 A, 250 V	T 1 A, 250 V	T 1 A, 250 V	T 1 A, 250 V	T 1 A, 250 V
Power I/O		U.S./Canada		Worldwide
Power input connector		Fixed		Fixed
Power cord plug		Edison (U.S.)		Bare wire

Light Source

Type	Color	Quantity	Power	Current	Lifespan
LED	Red GreenBlueAmberLime	3	3–4 W	700 mA	50,000 hours

Photometrics

Zoom	Beam Angle	Field Angle	Zoom Range	Illuminance @ 5 m
Narrow	18°	32°	18°	36 lux
Wide	67°	87°	87°	18 lux

Thermal

Maximum External Temperature	Cooling System
113 °F (45 °C)	Convection

DMX

I/O Connector	Channel Range
5-pin XLR	1, 3, 5, 7 10, 12, 13 or 16

Ordering

Product Name	Item Name	Item Code	UPC Number
Ovation F-55FC	OVATIONF55FC	03031384	781462217327

UL 1573 CSA C22.2 No. 166 E113093

Returns

Send the product prepaid, in the original box, and with the original packing and accessories. Chauvet will not issue call tags.

Call Chauvet and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return.

To submit a service request online, go to www.chauvetprofessional.com/service-request.

Clearly label the package with an RMA number. Chauvet will refuse any product returned without an RMA number.

Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.

Before sending the product, clearly write the following information on a piece of paper and place it inside the box:

• Your name
• Your address
• Your phone number
• RMA number

• A brief description of the problem

Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended.

Chauvet reserves the right to use its own discretion to repair or replace returned product(s).

Contact Us

General Information	Technical Support
Chauvet World Headquarters
Address: 5200 NW 108th Ave.	Voice: [phone]
Sunrise, FL 33351	Fax: [phone]
Voice: [phone]	Email: [e-mail]
Fax: [phone]
Toll Free: [phone]	Website: www.chauvetprofessional.com
Chauvet Europe Ltd
Address: Unit 1C	Email: [e-mail]
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK	Website: www.chauvetprofessional.eu
NG16 6NT
Voice: [phone]
Fax: [phone]
Chauvet Europe BVBA
Address: Stokstraat 18	Email: [e-mail]
9770 Kruishoutem
Belgium	Website: www.chauvetprofessional.eu
Voice: [phone]
Chauvet France
Address: 3, Rue Ampère	Email: [e-mail]
91380 Chilly-Mazarin
France	Website: www.chauvetprofessional.eu
Voice: [phone]
Chauvet Germany
Address: Bruno-Bürgel-Str. 11	Email: [e-mail]
28759 Bremen
Germany	Website: www.chauvetprofessional.eu
Voice: [phone]
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B(Entrance by Calle 2)	Email: [e-mail]
Zona Industrial Lerma	Website: www.chauvetprofessional.mx
Lerma, Edo. de México, CP 52000
Voice: [phone]

Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U.K., Ireland, France, Germany, Benelux, or Mexico, contact the dealer of record.