MG-120 - Water heater Emegé - Free user manual and instructions
Find the device manual for free MG-120 Emegé in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electric Water Heater |
| Brand | Emegé |
| Model | MG-120 |
| Capacity | 120 liters |
| Installation Type | Wall-mounted, vertical |
| Dimensions (Height x Diameter) | 1200 mm x 500 mm |
| Weight (empty) | 35 kg |
| Power Supply | 220-240 V, 50 Hz |
| Heating Power | 2000 W |
| Maximum Water Temperature | 75°C (adjustable) |
| Thermostat Range | 30-75°C |
| Pressure Rating | 0.8 MPa (8 bar) |
| Inner Tank Material | Enameled steel |
| Thermal Insulation | Polyurethane foam, 50 mm thickness |
| Corrosion Protection | Magnesium anode |
| Ingress Protection | IPX4 (splash-proof) |
| Main Functions | Adjustable thermostat, rapid heating, thermal retention |
| Safety Features | Overheat protection, pressure relief valve |
| Maintenance | Annual tank flush and anode inspection |
| Water Connections | 1/2 inch inlet and outlet |
| Included Accessories | Safety valve, mounting kit |
Frequently Asked Questions - MG-120 Emegé
What is the capacity of the Emegé MG-120 water heater?
The MG-120 has a 120-liter capacity, making it suitable for households of 3 to 4 people.
How do I set the water temperature on the MG-120?
Refer to the thermostat dial on the front panel. Turn it to your desired value between 30°C and 75°C. For energy savings, a setting around 60°C is recommended.
How long does it take to heat the full 120 liters?
With a 2000 W heating element, heating from 15°C to 75°C takes approximately 4-5 hours. Actual time may vary depending on the starting water temperature and ambient conditions.
How should I maintain the MG-120 water heater?
Perform annual maintenance by draining the tank to remove sediment, checking the magnesium anode, and inspecting the pressure relief valve. This prolongs the heater's life and ensures safety.
How do I replace the magnesium anode rod?
First, disconnect the power supply and close the water inlet. Drain the tank completely, then locate the anode mount (usually near the top or bottom flange). Unscrew the old anode and install a new one, then refill and power on.
Why does the pressure relief valve release water?
The valve releases water if the internal pressure exceeds a safe level, preventing tank damage. If it leaks continuously, the valve may be defective and should be replaced.
How energy efficient is the MG-120?
With 50 mm polyurethane insulation and a thermostat that cuts off heating at the set point, standby heat loss is minimal. Using off-peak electricity can further reduce operating costs.
What should I do if the water heater overheats or trips the reset?
Press the reset button on the thermostat after turning off the power. If the problem recurs, check the heating element, thermostat, and mains voltage. Seek professional assistance if needed.
Can the MG-120 be installed horizontally?
The MG-120 is designed for vertical wall-mounted installation. Horizontal mounting is not recommended and may damage the internal elements or affect performance.
Are spare parts available for the Emegé MG-120?
Yes, spare parts such as the heating element, thermostat, magnesium anode, and pressure relief valve are available from authorized Emegé distributors. Always use original parts for safety.
User questions about MG-120 Emegé
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual MG-120 - Emegé and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MG-120 by Emegé.
USER MANUAL MG-120 Emegé
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Emegé
Model : MG-120
Category : Water heater