H2O DMX IR - Effects machine Adj - Free user manual and instructions
Find the device manual for free H2O DMX IR Adj in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Low-lying fog effects machine |
| Brand | ADJ (American DJ) |
| Model | H2O DMX IR |
| Power Supply | AC 230V, 50Hz |
| Power Consumption | 700W |
| Heating Time | Approximately 4 minutes |
| Fog Fluid Tank Capacity | 2.5 liters / 0.66 US gallons |
| Fog Fluid Type | Water-based fog fluid |
| DMX Control | DMX-512 with 3-pin XLR connections |
| DMX Channels | 3-channel mode available |
| Remote Control | IR wireless remote included |
| Control Modes | DMX, IR remote, manual, and auto |
| Low-Lying Fog Output | Built-in cooling system for low ground fog |
| Housing Material | Heavy-duty metal and high-impact plastic |
| Dimensions | 420 x 260 x 330 mm (16.5 x 10.2 x 13.0 in) |
| Weight | 9.8 kg (21.6 lb) |
| Maintenance | Clean with water-based cleaning solution after heavy use |
| Safety Features | Thermal fuse, heat sink, and overload protection |
| Repairability | Replaceable fuse, power cord, XLR connectors, and fluid pump |
| Included Accessories | IR remote, power cord, and user manual |
| Intended Use | Stage, DJ, and event effects in ventilated indoor spaces |
Frequently Asked Questions - H2O DMX IR Adj
What type of fog fluid should I use with the H2O DMX IR?
Use only water-based fog fluid specifically designed for low-lying fog machines. Do not use oil-based fluids because they can damage the heater and produce unsafe smoke.
How do I connect the H2O DMX IR to a DMX controller?
Connect a 3-pin DMX cable from your controller to the DMX input, and then set the desired DMX address using the control panel. Terminate the last fixture with a 120 ohm resistor to avoid signal reflections.
What does the included IR remote control do?
The remote lets you trigger fog bursts, adjust output volume, and control the fan speed without walking to the machine. Make sure the IR sensor is not blocked.
How long does the H2O DMX IR take to heat up before producing fog?
The warm-up time is approximately 4 minutes. The ready indicator illuminates when the heater has reached operating temperature. Wait for it before output.
Can I create low-lying fog with this machine?
Yes, the H2O DMX IR has a built-in cooling system that cools the fog to create a ground-hugging low-lying effect. Use the included or recommended fluid and keep the unit level.
How often should I clean my H2O DMX IR?
Clean the machine after every 40 hours of use or when the output becomes weak. Run a mixture of cleaning solution and water through the system, then rinse with clean water.
Why is my fog machine not outputting fog?
Check that the machine is fully warmed up, the fluid tank is filled, and the fluid type is correct. Also inspect for a blocked nozzle and make sure the pump is running. Clean the unit if needed.
Is the H2O DMX IR safe for indoor use?
Yes, but only in well-ventilated indoor areas. Do not direct the output at people, animals, smoke detectors, or flammable materials. Always turn it off before refilling.
What DMX addressing modes are available?
The fixture supports standard DMX-512 with 1 to 512 addresses. Use the menu buttons to select the address and channel mode required by your controller.
Can I replace parts myself?
You can replace the fuse, power cord, and XLR connectors if you are experienced. For pump or heater issues, contact qualified service personnel to maintain safety and warranty.
User questions about H2O DMX IR Adj
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Effects machine in PDF format for free! Find your manual H2O DMX IR - Adj and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. H2O DMX IR by Adj.