Nyquist NQ-E7010 - Uncategorized Bogen - Free user manual and instructions
Find the device manual for free Nyquist NQ-E7010 Bogen in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Network IP audio amplifier for paging and background music systems |
| Brand | Bogen |
| Model | Nyquist NQ-E7010 |
| Amplifier Output | 60W continuous; supports 70V, 25V, and 8-ohm speaker lines |
| Network Interface | 10/100 Ethernet with RJ-45 connector, TCP/IP, SIP, multicast and unicast paging |
| Audio Inputs | Two balanced mic/line inputs plus one auxiliary line input with screw terminals |
| Audio Outputs | Speaker output terminal strip for 70V/25V/8-ohm loads; line output for daisy-chaining |
| Control Interfaces | Contact closures, page input, logic outputs for zone control and priority override |
| Configuration | Web-based configuration via built-in web server; DHCP and static IP support |
| Signaling | Supports call paging, SIP calls, contact closures, and scheduled tones |
| Front Panel Indicators | Power, network link/activity, amplifier status, and audio signal LEDs |
| Mounting | 19-inch rack-mount or wall-mount with included hardware |
| Dimensions | Approximately 17.0 x 1.7 x 8.3 in (432 x 44 x 211 mm) |
| Weight | Approximately 7.0 lb (3.2 kg) |
| Power Source | 24V DC external power adapter (100-240V AC input), low standby consumption |
| Operating Environment | 0°C to 40°C (32°F to 104°F), 20-80% non-condensing humidity |
| Care and Cleaning | Wipe exterior with dry soft cloth; do not use liquid or aerosol cleaners |
| Safety Warnings | Provide adequate ventilation; do not block air vents; disconnect power before cleaning |
| Spare Parts and Repair | Power supply and network module are replaceable by qualified service technicians; no user-serviceable components |
| General Information | 18-page multilingual installation manual included; designed for commercial paging systems |
Frequently Asked Questions - Nyquist NQ-E7010 Bogen
How do I assign an IP address to the NQ-E7010?
The device supports DHCP by default. Connect it to your network, find the leased address in your router's client list, then open that address in a browser to access the web-based configuration page. You can set a static IP there for permanent installation.
Can this amplifier be used for both paging and background music at the same time?
Yes, the NQ-E7010 can distribute background music while remaining ready for priority paging. Paging calls or contact-closure pages automatically duck the music and return to music after the page ends.
What speaker loads are compatible with the 60W amplifier?
Connect either 70V/25V distributed speaker lines or 8-ohm low-impedance speakers. Match the total speaker wattage to the 60W output and do not exceed the rated impedance or transformer tap.
How do I return the device to factory defaults?
Press and hold the Reset button on the front panel for about 10 seconds, or restore defaults from the web interface by selecting Factory Reset. Configuration is then reset to DHCP and default password.
Does the NQ-E7010 receive power over Ethernet?
No, the amplifier section requires a dedicated 24V DC power supply. The Ethernet port is used for control and audio streaming only and cannot supply enough power for 60W amplification.
Can I connect the unit to a VoIP telephone system?
Yes, it supports SIP registration, so you can connect to most VoIP/PBX systems and enable paging from call stations. It also supports multicast/unicast paging from Bogen Nyquist software and other compatible controllers.
How do I set up scheduled bells or tones?
Use the built-in schedule and tone generator. In the web interface, create time events and choose the tone or audio file to play over the selected zone at the programmed time.
What connections are used for microphones and line sources?
The rear panel includes two balanced mic/line inputs and one auxiliary line input. Connect using shielded cable to the screw terminals, set the input type, and adjust gain for each input.
How should I maintain and clean the amplifier?
Disconnect power before cleaning. Use a dry, soft cloth to wipe the casing and front panel. Do not use liquids or spray cleaners. Periodically check that ventilation openings are free from dust and ensure wiring screws remain tight.
Can I mount the NQ-E7010 in a rack?
Yes, the unit has a 19-inch rack-mount chassis and comes with rack ears. It can also be wall-mounted with the optional bracket, leaving enough space around the vents for proper airflow.
User questions about Nyquist NQ-E7010 Bogen
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual Nyquist NQ-E7010 - Bogen and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Nyquist NQ-E7010 by Bogen.
USER MANUAL Nyquist NQ-E7010 Bogen
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Bogen
Model : Nyquist NQ-E7010
Category : Uncategorized