S100 - Uncategorized UNGO - Free user manual and instructions
Find the device manual for free S100 UNGO in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Vehicle Security Alarm System |
| Model | S100 |
| Brand | UNGO |
| Compatible Voltage | 12 V DC vehicle electrical system |
| Control Unit Dimensions | 4.7 x 2.5 x 1.1 inches (119 x 63 x 28 mm) |
| Remote Key Fob Dimensions | 2.2 x 1.4 x 0.6 inches (56 x 36 x 15 mm) |
| Product Weight | 6.7 oz (190 g) for the main control unit |
| Operating Frequency | 433.92 MHz remote control signal |
| Standby Current Draw | Max 25 mA |
| Siren Output | 120 dB at 1 meter |
| Anti-Theft Features | Shock sensor, panic function, and immobilizer relay output |
| Remote Functions | Arm, disarm, panic, trunk release, and optional remote start interface |
| Status Indication | Built-in LED status light and siren chirps; valet mode available |
| Programming | Key fob programming using ignition cycle and valet button |
| Installation | Universal wiring harness; professional installation recommended |
| Operating Temperature | -30 to +70 C (-22 to +158 F) |
| Maintenance and Cleaning | Wipe the remote fob with a soft dry cloth; inspect wiring and antenna connections regularly |
| Safety | Fused 12 V power lead; disconnect the vehicle battery before installation or service |
| Spare Parts and Repairability | Replacement remote key fobs, button cell batteries, and wiring harness available; repair by authorized service center |
| Documentation | User manual and installation guide, 36 pages, in English |
Frequently Asked Questions - S100 UNGO
What is the UNGO S100?
The UNGO S100 is a professional-grade vehicle security alarm system designed for 12 V cars and light trucks. It provides keyless entry, shock detection, siren output, and an immobilizer-ready relay output to help deter theft.
Can I install the UNGO S100 myself?
The system is sold with a universal wiring harness, but professional installation is strongly recommended. It involves connecting the power, ground, door triggers, siren, and optional ignition wires. If you are not experienced with automotive wiring, consult a certified installer to avoid damaging the vehicle or the alarm.
How do I arm and disarm the system?
Press the lock button on the remote key fob to arm the system. Press the unlock button to disarm it. When armed, the LED status indicator flashes; when disarmed, the siren may chirp once or twice depending on the programmed settings. You can also use the valet mode to disable alarm functions during service.
How do I adjust the shock sensor sensitivity?
Locate the shock sensor adjustment knob on the main control unit. Use a small screwdriver to turn the knob clockwise for higher sensitivity or counterclockwise for lower sensitivity. After adjusting, arm the system and gently tap the vehicle to test the response. Be careful not to set it too high to avoid false alarms.
What should I do if the remote key fob does not work?
First check the battery inside the remote key fob and replace it with a fresh CR2032 or equivalent button cell. Make sure you are within the operating range, usually about 30 to 50 meters. If the fob still fails, reprogram it following the user manual procedure or have a technician inspect the receiver.
Does the system have a panic function?
Yes, press and hold the panic button on the remote for about 2 seconds. This triggers the siren and parking light output to attract attention. Press any remote button or turn the ignition on to stop the panic mode.
How do I replace the remote battery?
Open the remote key fob case by inserting a small screwdriver into the seam. Remove the old battery and insert a new CR2032 button cell with the positive terminal facing up. Snap the case back together and verify that the LED on the fob flashes when you press a button.
Does the UNGO S100 support remote engine start?
The S100 has an optional remote start-ready interface; however, a separate remote start module is required to control the ignition circuit. Refer to the manual and consult a professional installer if you want remote start capability.
Why does the siren chirp twice when arming?
The number of chirps indicates the system status. A single chirp usually means the system is armed normally. If the siren chirps twice, a protected zone, such as a door or the shock sensor, was not closed or is in bypass mode. Check the doors, hood, and trunk, and disarm/re-arm the system to reset.
How do I reset the system to factory defaults?
Turn the ignition to the ON position, press and hold the valet/program button, then turn it OFF and back ON within a few seconds. Keep holding until the siren chirps three times. Release the button, and the system will return to factory default settings. Note that this will erase any custom remote programming.
User questions about S100 UNGO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual S100 - UNGO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. S100 by UNGO.
USER MANUAL S100 UNGO
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : UNGO
Model : S100
Category : Uncategorized