Script i - Loudspeaker Martin Logan - Free user manual and instructions
Find the device manual for free Script i Martin Logan in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | On-wall / bookshelf loudspeaker |
| Brand | Martin Logan |
| Model | Script i |
| Category | Loudspeaker |
| Enclosure Design | Two-way acoustic suspension with rear port |
| Drivers | 1” Folded Motion tweeter, 4” polypropylene cone mid-bass |
| Frequency Response | 70 Hz – 20 kHz (±3 dB) |
| Sensitivity | 90 dB at 2.83 Vrms/1m |
| Impedance | 4 ohms (compatible with 4–8 ohm amplifiers) |
| Crossover Frequency | 2,000 Hz |
| Power Handling | 100 watts RMS, 200 watts peak |
| Recommended Amplifier Power | 20 – 100 watts per channel |
| Dimensions (W x H x D) | 12.5 x 7.5 x 4.5 in (31.8 x 19.0 x 11.4 cm) |
| Weight | 5.5 lbs (2.5 kg) |
| Mounting Options | Keyhole bracket and 1/4” -20 threaded insert |
| Connector Type | Single set of gold-plated binding posts |
| Suitable Room Size | Small to medium rooms (10–25 m²) |
| Cleaning and Maintenance | Wipe with a soft dry cloth; do not use water or cleaning agents |
| Safety Instructions | Keep away from moisture; do not place on unstable surfaces; ensure proper ventilation |
| Spare Parts and Reparability | Contact authorized Martin Logan dealer for replacement drivers and service |
| Package Contents | 1 loudspeaker, mounting bracket, foam port plugs, user manual |
| Warranty | 5 years limited (electronics and drivers) |
Frequently Asked Questions - Script i Martin Logan
How should I position the Script i speakers?
Position the speakers at ear level when seated. For stereo, angle them slightly toward the listening position. Keep them at least 4 inches from the rear wall to avoid bass boom. If using them as rears, place them behind and above the listening area.
Can I use the Script i as a center channel speaker?
Yes, the Script i works well as a center channel. Place it horizontally or vertically near the TV, ideally centered to match the dialogue with on-screen action. Make sure the tweeter is angled toward ear level.
What gauge of speaker wire should I use?
For runs up to 20 feet, use 16-gauge wire. For longer runs, 14-gauge or thicker is recommended. Ensure the wire is firmly connected to the binding posts and amplifier terminals.
How do I clean my Martin Logan Script i?
Use a soft dry cloth to gently wipe the cabinet. Do not use water, household cleaners, or spray polishes. For grilles, a vacuum with a brush attachment works well. Avoid touching the tweeter as it is delicate.
How long is the break-in period for my new speakers?
Most speakers achieve optimal performance after 20–50 hours of music playback. During break-in, you may notice changes in bass and treble response. Play a variety of content at moderate volume to help the drivers loosen up.
How can I mount the Script i on the wall securely?
Use the supplied keyhole bracket and a robust screw anchored into a wall stud, or use a wall anchor rated for at least 10 kg. Align the speaker so the keyhole engages the screw head, then gently lower until it locks. Always verify the mount is secure before releasing.
Why is there no sound from my speaker?
First check that the amplifier is on and not muted. Verify speaker wire connections at both ends, ensuring positive and negative terminals are matched. Test with a different audio source. If one speaker works, swap wires to see if the issue follows the speaker or the channel.
Can I use a subwoofer with the Script i?
Yes, the Script i has a limited bass response (down to 70 Hz), so a subwoofer is recommended for full-range sound. Set the subwoofer crossover around 80–100 Hz. In many receivers, set the speakers to “small” to route low frequencies to the subwoofer.
Are the drivers replaceable if damaged?
Yes, the tweeter and bass drivers can be replaced. Contact an authorized Martin Logan service center or your dealer to order genuine parts. Do not attempt to repair the drivers yourself as it may void the warranty.
What amplifier power is recommended?
A 20 to 100 watts per channel amplifier is ideal. The speaker has an impedance of 4 ohms, so ensure the amplifier is rated to drive 4-ohm loads. Higher power with clean headroom is preferred over underpowered amps that may clip.
User questions about Script i Martin Logan
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Loudspeaker in PDF format for free! Find your manual Script i - Martin Logan and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Script i by Martin Logan.
USER MANUAL Script i Martin Logan
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Martin Logan
Model : Script i
Category : Loudspeaker