PG1405 - Uncategorized IFM - Free user manual and instructions
Find the device manual for free PG1405 IFM in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Process Display & Controller |
| Brand | IFM |
| Model | PG1405 |
| Dimensions (W x H x D) | 80 x 80 x 50 mm |
| Weight | 250 g |
| Power Supply | 24 V DC (18-32 V DC) |
| Display Type | 4-digit LED, 7-segment |
| Input Signal | 4-20 mA, 0-10 V |
| Output Configuration | 2 relay outputs |
| Communication Interface | IO-Link (optional) |
| Protection Rating | IP65 (front panel), IP20 (housing) |
| Operating Temperature | -10 °C to 60 °C |
| Storage Temperature | -20 °C to 70 °C |
| Housing Material | Polycarbonate |
| Mounting Type | Panel mount |
| Programmable Set Points | Yes, via front keys |
| Status Indication | LED indicators for outputs |
| Maintenance | Clean with dry cloth, no solvents |
| Safety Features | Electrical isolation, overload protection |
| Spare Parts Availability | Original spare parts from manufacturer |
| Reparability | Serviceable by qualified personnel |
Frequently Asked Questions - PG1405 IFM
How do I install the PG1405?
To install the PG1405, ensure the power is off, mount the device into a standard 80x80 mm panel cutout, and secure it with the provided clamps. Connect the power supply (24 V DC) and the input/output signals according to the wiring diagram in the manual. Finally, power on and configure the parameters using the front keys.
How can I configure the set points?
Use the programming keys on the front panel to enter the menu. Navigate to the set point parameters, adjust the desired values, and press the Enter key to save. The display will indicate the confirmed settings.
What is the power supply range for this device?
The PG1405 operates on a DC power supply with a range of 18 to 32 V DC. The recommended nominal voltage is 24 V DC. Ensure the power source is stable and properly filtered.
Can I use the PG1405 with a 4-20 mA sensor?
Yes, the PG1405 accepts 4-20 mA analog input signals. You can also use 0-10 V signals. Configure the input type in the device settings to match your sensor output.
How should I clean the PG1405?
Clean the front panel with a soft, dry cloth to remove dust or dirt. Do not use solvents, abrasive cleaners, or water directly on the device. For stubborn stains, slightly dampen the cloth with water.
What does the LED display show?
The 4-digit LED display shows the current process value, such as pressure, temperature, or level, depending on the connected sensor. It can also display error codes or configuration menus during setup.
How do I perform a factory reset?
To reset the PG1405 to factory defaults, press and hold the Enter key for approximately 10 seconds while the device is powered on. The display will show a confirmation message. Release the key to complete the reset.
Is the PG1405 waterproof?
The front panel is rated IP65, meaning it is protected against water jets and dust, making it suitable for washdown environments. The rear housing is rated IP20, so it should not be exposed to moisture.
How do I connect the relay outputs?
Connect the relay outputs to the terminal blocks on the rear of the device. Each relay has common (C), normally open (NO), and normally closed (NC) terminals. Refer to the wiring diagram in the manual for exact pin assignments.
What are the dimensions of the PG1405?
The PG1405 has a square front bezel of 80 x 80 mm and a body depth of approximately 50 mm. The panel cutout required is 72 x 72 mm with a minimum panel thickness of 1.5 mm.
User questions about PG1405 IFM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual PG1405 - IFM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PG1405 by IFM.
USER MANUAL PG1405 IFM
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : IFM
Model : PG1405
Category : Uncategorized