IP-A750RX - Uncategorized CYP - Free user manual and instructions
Find the device manual for free IP-A750RX CYP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | AV over IP Receiver |
| Brand | CYP |
| Model | IP-A750RX |
| Category | A/V Distribution |
| Video Input | Ethernet (IP) via RJ-45 |
| Video Output | HDMI |
| Connectors | 1 x RJ-45 (IP In), 1 x HDMI Out, 1 x IR In, 1 x IR Out |
| Video Resolution | Up to 4K UHD @ 60Hz 4:4:4 |
| Audio Support | PCM, Dolby Digital, DTS, and multi-channel audio |
| Power Supply | 12V DC, 1A adapter included |
| Dimensions (W x D x H) | 160 mm x 90 mm x 25 mm |
| Weight | 450 g |
| Mounting | Surface mount with included bracket |
| Controls | Front panel buttons and IR remote |
| Signal Transmission | Standard IP network, up to 100m per hop |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Housing Material | Metal housing |
| LED Indicators | Power, Link, and Status |
| Warranty | 2 years |
Frequently Asked Questions - IP-A750RX CYP
How do I connect the IP-A750RX to a network switch?
Connect the IP-A750RX to a network switch using a standard Ethernet cable (Cat5e or better). Plug one end into the RJ-45 port labeled IP In on the receiver, and the other end into an available port on your switch.
How do I pair the receiver with a transmitter?
The IP-A750RX and its corresponding transmitter automatically pair when connected to the same network. Ensure both devices are powered on and connected to the same subnet. Use the front panel or IR remote to adjust the EDID or IP settings if needed.
What video resolutions are supported?
The receiver supports video resolutions up to 4K UHD @ 60Hz 4:4:4. It is also compatible with 1080p, 720p, and lower resolutions, making it suitable for various display devices.
How do I control the device via IR?
Connect the included IR emitter to the IR Out port for receiving signals, or use an IR receiver on the IR In port to pass signals to the transmitter. Point the remote control at the IR receiver to control the source device.
Can I use it over a standard Ethernet cable?
Yes, the IP-A750RX works with Cat5e, Cat6, or higher cabling. Use a good quality cable to ensure reliable transmission and avoid signal degradation over longer distances.
How do I reset to factory defaults?
To reset the IP-A750RX to factory defaults, press and hold the front panel reset button for approximately 10 seconds until the Status LED flashes. Release the button and the device will reboot with default settings.
What should I do if there is no video output?
First, verify that the HDMI cable is properly connected to the output and the display. Check that the transmitter is sending a signal and that the network link LED is lit. If the issue persists, try changing the EDID mode via the front panel or restarting the device.
Is Power over Ethernet (PoE) supported?
No, the IP-A750RX does not support PoE. It must be powered using the included 12V DC power adapter. Please ensure the adapter is securely connected and supplying power.
How do I mount the receiver?
The IP-A750RX includes a surface mounting bracket. Attach the bracket to a stable surface using screws (not included), then slide the receiver onto the bracket until it clicks into place.
What is the maximum distance between transmitter and receiver?
The maximum recommended distance over a single Ethernet cable is 100 meters. For longer transmission, you can use multiple switches or a fiber optic converter to extend the IP network.
User questions about IP-A750RX CYP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual IP-A750RX - CYP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. IP-A750RX by CYP.