Power P-2510 - Receiver JBL - Free user manual and instructions
Find the device manual for free Power P-2510 JBL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Stereo receiver |
| Brand | JBL |
| Model | Power P-2510 |
| Power output | 50W per channel into 8 ohms |
| Frequency response | 20 Hz - 20 kHz |
| Signal-to-noise ratio | 80 dB (MM phono) |
| Total harmonic distortion | 0.05% at rated power |
| Audio inputs | Phono, CD, Tuner, Tape |
| Audio outputs | Speaker A/B, Headphone, Tape monitor |
| Speaker impedance | 4 - 8 ohms |
| Dimensions (W x H x D) | 17.3 x 4.5 x 12.2 inches (44 x 11.5 x 31 cm) |
| Weight | 14.3 lbs (6.5 kg) |
| Power supply | AC 120V / 60Hz |
| Power consumption | 150W |
| Tuner range | FM 87.5 - 108 MHz, AM 530 - 1600 kHz |
| Cleaning | Use a soft, dry cloth to clean the exterior. |
| Safety | Keep away from moisture; unplug before cleaning. |
| Repair | Contact an authorized JBL service center for spare parts. |
Frequently Asked Questions - Power P-2510 JBL
How do I connect my speakers to the JBL Power P-2510?
Use the speaker terminals on the back panel. For stereo, connect the left speaker to the left terminals (red to +, black to -) and the right speaker to the right terminals. Ensure the impedance is between 4 and 8 ohms.
How do I select the input source?
Press the Source button repeatedly to cycle through inputs such as Tape, CD, Tuner, and Phono. The selected source will appear on the display.
Why is there no sound coming from the receiver?
Check that the correct source is selected, the volume is not at minimum, and speakers are properly connected. Also ensure the Speaker A/B switch is set to the terminals you are using.
How should I clean the JBL Power P-2510?
Unplug the receiver and wipe the exterior with a soft, dry cloth. Do not use water, solvents, or abrasive cleaners. For persistent dirt, slightly dampen the cloth and wring it well before wiping.
Can I use 4-ohm speakers with this receiver?
Yes, the receiver supports speakers with impedance between 4 and 8 ohms. Make sure not to connect speakers with impedance lower than 4 ohms, as this may cause overheating.
How do I connect a turntable to the receiver?
Connect the turntable to the Phono input on the back. Ensure your turntable has a moving magnet (MM) cartridge, as the receiver provides the necessary phono preamp.
What is the FM antenna connection for?
The FM antenna connection accepts a 75-ohm coaxial cable or a 300-ohm twin-lead wire. Connect an appropriate antenna to improve stereo FM reception. Place the antenna away from metal objects for best results.
How can I reset the receiver?
Switch off the receiver and unplug it from the AC outlet for at least 30 seconds, then plug it back in and turn it on. This clears temporary electronic issues.
Is it safe to leave the receiver turned on for long periods?
The receiver is designed for reliable operation, but it is recommended to turn off the unit when not in use. Ensure proper ventilation around the unit to avoid heat buildup.
How do I set the sound balance between left and right channels?
Use the Balance knob on the front panel. Turn it clockwise to increase right channel volume, counterclockwise to increase left channel volume. Set it to the middle for equal output.
User questions about Power P-2510 JBL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Power P-2510 - JBL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Power P-2510 by JBL.
USER MANUAL Power P-2510 JBL
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : JBL
Model : Power P-2510
Category : Receiver